SIST EN 16228-5:2014
(Main)Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
EN 16228-5, together with part 1, deals with all significant hazards for diaphragm walling equipment when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4). The requirements of this part are complementary to the common requirements formulated in EN 16228-1:2014.
Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für Schlitzwandarbeiten
Diese Europäische Norm behandelt zusammen mit Teil 1 alle signifikanten Gefährdungen für Geräte für Schlitzwandarbeiten, wenn sie bestimmungsgemäß und unter den Bedingungen der Fehlanwendung, die ver-nünftigerweise vom Hersteller vorhersehbar sind und mit der gesamten Lebensdauer der Maschine in Verbindung stehen, verwendet werden (siehe Abschnitt 4).
Die Anforderungen in diesem Teil gelten zusätzlich zu den in EN 16228-1:2014 gestellten Anforderungen.
Das vorliegende Dokument wiederholt nicht die Anforderungen von EN 16228-1, sondern ergänzt oder ersetzt die Anforderungen für die Anwendung von Geräten für Schlitzwandarbeiten.
Machines de forage et de fondation - Sécurité - Partie 5: Machines pour parois moulées dans le sol
Le présent document spécifie les prescriptions de sécurité particulières relatives aux machines pour parois
moulées dans le sol, lorsqu'elle sont utilisées normalement et dans les conditions prévues par le fabricant. Le
présent document spécifie les mesures techniques appropriées pour éliminer ou réduire les risques dus aux
phénomènes dangereux significatifs.
Les prescriptions du présent document viennent en complément des prescriptions communes spécifiées dans
la partie 1. Le présent document ne répète pas les prescriptions de la partie 1, mais en ajoute certains
applicables aux machines pour parois moulées dans le sol.
Le présent document spécifie les mesures techniques appropriées pour éliminer ou réduire les risques dus
aux phénomènes dangereux, situations et événements dangereux significatifs détaillés à l'Article 4 ci-après.
Oprema za vrtanje in temeljenje - Varnost - 5. del: Oprema za izdelavo membranskih sten
Standard EN 16228-5 skupaj s 1. delom obravnava vsa večja tveganja za opremo za izdelavo membranskih sten, če se uporablja, kot je bilo predvideno, in pod pogoji nepravilne uporabe, ki jih je razumno predvidel proizvajalec, v zvezi s celotno življenjsko dobo opreme (gl točko 4). Zahteve iz tega dela dopolnjujejo splošne zahteve iz standarda EN 16228-1:2014.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Oprema za vrtanje in temeljenje - Varnost - 5. del: Oprema za izdelavo membranskih stenGeräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für SchlitzwandarbeitenMachines de forage et de fondation - Sécurité - Partie 5: Machines pour parois moulées dans le solDrilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment93.020Zemeljska dela. Izkopavanja. Gradnja temeljev. Dela pod zemljoEarthworks. Excavations. Foundation construction. Underground works53.100Stroji za zemeljska delaEarth-moving machineryICS:Ta slovenski standard je istoveten z:EN 16228-5:2014SIST EN 16228-5:2014en,fr01-oktober-2014SIST EN 16228-5:2014SLOVENSKI
STANDARDSIST EN 996:2000+A3:2009SIST EN 791:2000+A1:20091DGRPHãþD
SIST EN 16228-5:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16228-5
May 2014 ICS 93.020 Supersedes EN 791:1995+A1:2009, EN 996:1995+A3:2009English Version
Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
Machines de forage et de fondation - Sécurité - Partie 5: Machines pour parois moulées
Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für Schlitzwandarbeiten This European Standard was approved by CEN on 6 March 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16228-5:2014 ESIST EN 16228-5:2014
EN 16228-5:2014 (E) 2 Contents Page Foreword .3 Introduction .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 List of additional significant hazards .6 5 Safety requirements and/or protective measures .7 5.1 General .7 5.2 Requirements for strength and stability .8 5.2.1 General .8 5.2.2 Loads from diaphragm wall cutting tools .8 5.2.3 Stability of diaphragm walling rig .8 5.3 Winches and pulleys .9 5.4 Control devices . 10 5.4.1 General .
...
SLOVENSKI STANDARD
oSIST prEN 16228-5 rev:2011
01-junij-2011
Oprema za vrtanje in temeljenje - Varnost - 5. del: Oprema za izdelavo
membranskih sten
Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für
Schlitzwandarbeiten
Machines de forage et de fondation - Sécurité - Partie 5: Machines pour parois moulées
dans le sol
Ta slovenski standard je istoveten z: prEN 16228-5 rev
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
oSIST prEN 16228-5 rev:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16228-5 rev:2011
---------------------- Page: 2 ----------------------
oSIST prEN 16228-5 rev:2011
EUROPEAN STANDARD
DRAFT
prEN 16228-5 rev
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2011
ICS 93.020 Will supersede EN 791:1995+A1:2009, EN
996:1995+A3:2009
English Version
Drilling and foundation equipment - Safety - Part 5: Diaphragm
walling equipment
Machines de forage et de fondation - Sécurité - Partie 5: Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil
Machines pour parois moulées dans le sol 5: Geräte für Schlitzwandarbeiten
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 151.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16228-5 rev:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16228-5 rev:2011
prEN 16228-5:2011 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .4
2 Normative references .4
3 Terms and definitions .5
4 List of significant hazards .6
5 Safety requirements and/or protective measures .7
5.1 General .7
5.2 Operation in slurries and muds etc. .7
5.3 Requirements for strength and stability .7
5.3.1 Strength of a diaphragm walling rig .7
5.3.2 Loads from diaphragm walling cutting tools .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.