District heating pipes - Factory made flexible pipe systems with a lower temperature profile - Part 1: Classification, general requirements and test methods

This document specifies classification, general requirements and test methods for flexible, factory made, buried district heating pipe systems.
This document is intended to be used in conjunction with part 2 or 3, as applicable.
This document is applicable to a maximum continuous media temperature of 80 °C (part 2 and 3) and design pressures of 0,6 MPa to 1 MPa.
The pipe systems are designed for a service life of at least 50 years. For pipe systems with plastic service pipes, the respective temperature profiles are defined in EN XXXX-2 and EN XXXX-3.
NOTE   For the transport of other liquids, for example potable water, additional requirements can be applicable.

Fernwärmerohre - Flexible Rohrsysteme mit einem niedrigeren Temperaturprofil - Teil 1: Klassifikation, allgemeine Anforderungen und Prüfungen

Dieses Dokument legt die Klassifikation, allgemeine Anforderungen und Prüfverfahren für flexible, werkmäßig hergestellte, erdverlegte Fernwärmenetze fest.
Dieses Dokument ist ausschließlich für die Anwendung in Verbindung mit EN 17878-2 oder EN 17878-3, wie jeweils zutreffend, vorgesehen.
Dieses Dokument ist für eine maximale Betriebstemperatur von 80 °C und einen maximalen zulässigen Betriebsdruck bis einschließlich 1,0 MPa anwendbar.
Die Rohrsysteme sind für eine Nutzungsdauer von 50 Jahren ausgelegt. Für Rohrsysteme mit Mediumrohren aus Kunststoff sind die entsprechenden Temperaturprofile in EN 17878-2:2023 und EN 17878-3:2023 festgelegt.
Für den Transport von anderen Flüssigkeiten, wie z. B. Trinkwasser, können zusätzliche Anforderungen gelten.

Tuyaux de chauffage urbain - Systéme de tuyaux flexibles préisolés - Partie 1: Classification, exigences générales et méthodes d'essai

No Scope Available

Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi z nižjim temperaturnim profilom - 1. del: Klasifikacija, splošne zahteve in preskusne metode

Ta dokument določa klasifikacijo, splošne zahteve in preskusne metode za tovarniško izdelane gibke podzemne cevne sisteme za daljinsko ogrevanje.
Ta dokument je namenjen za uporabo skupaj z 2. ali 3. delom (kot je ustrezno).
Ta dokument se uporablja za najvišjo stalno temperaturo medijev 80 °C (2. in 3 del) in za konstrukcijske tlake od 0,6 MPa do 1 MPa.
Predvidena življenjska doba cevnih sistemov je najmanj 50 let. Temperaturni razponi za cevne sisteme z delovnimi cevmi iz polimernih materialov so določeni v standardih EN XXXX-2 in EN XXXX-3.
OPOMBA: Za transport drugih tekočin, na primer pitne vode, morda veljajo dodatne zahteve.

General Information

Status
Published
Public Enquiry End Date
04-Oct-2022
Publication Date
11-Apr-2024
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
25-Mar-2024
Due Date
30-May-2024
Completion Date
12-Apr-2024

Buy Standard

Standard
EN 17878-1:2024
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17878-1:2022
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17878-1:2024
01-maj-2024
Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi z nižjim
temperaturnim profilom - 1. del: Klasifikacija, splošne zahteve in preskusne
metode
District heating pipes - Factory made flexible pipe systems with a lower temperature
profile - Part 1: Classification, general requirements and test methods
Fernwärmerohre - Flexible Rohrsysteme mit einem niedrigeren Temperaturprofil - Teil 1:
Klassifikation, allgemeine Anforderungen und Prüfungen
Tuyaux de chauffage urbain - Systéme de tuyaux flexibles préisolés - Partie 1:
Classification, exigences générales et méthodes d'essai
Ta slovenski standard je istoveten z: EN 17878-1:2024
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST EN 17878-1:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17878-1:2024

---------------------- Page: 2 ----------------------
SIST EN 17878-1:2024


EN 17878-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2024
EUROPÄISCHE NORM
ICS 23.040.07
English Version

District heating pipes - Factory made flexible pipe systems
with a lower temperature profile - Part 1: Classification,
general requirements and test methods
Tuyaux de chauffage urbain - Système de tuyaux Fernwärmerohre - Flexible Rohrsysteme mit einem
flexibles préisolés - Partie 1 : Classification, exigences niedrigeren Temperaturprofil - Teil 1: Klassifikation,
générales et méthodes d'essai allgemeine Anforderungen und Prüfungen
This European Standard was approved by CEN on 14 August 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17878-1:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 17878-1:2024
EN 17878-1:2024 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols, indices and abbreviations . 7
4 Classification . 10
5 Design requirements . 10
5.1 Thermal insulation properties . 10
5.2 Bending test .
...

SLOVENSKI STANDARD
oSIST prEN 17878-1:2022
01-september-2022
Cevi za daljinsko ogrevanje - Tovarniško izdelani gibki cevni sistemi z nižjim
temperaturnim profilom - 1. del: Klasifikacija, splošne zahteve in preskusne
metode
District heating pipes - Factory made flexible pipe systems with a lower temperature
profile - Part 1: Classification, general requirements and test methods
Fernwärmerohre - Flexible Rohrsysteme mit einem niedrigeren Temperaturprofil - Teil 1:
Klassifikation, allgemeine Anforderungen und Prüfungen
Tuyaux de chauffage urbain - Systéme de tuyaux flexibles préisolés - Partie 1:
Classification, exigences générales et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 17878-1
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
23.040.20 Cevi iz polimernih materialov Plastics pipes
oSIST prEN 17878-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17878-1:2022

---------------------- Page: 2 ----------------------
oSIST prEN 17878-1:2022


DRAFT
EUROPEAN STANDARD
prEN 17878-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2022
ICS 23.040.07
English Version

District heating pipes - Factory made flexible pipe systems
with a lower temperature profile - Part 1: Classification,
general requirements and test methods
Tuyaux de chauffage urbain - Systéme de tuyaux Fernwärmerohre - Flexible Rohrsysteme mit einem
flexibles préisolés - Partie 1: Classification, exigences niedrigeren Temperaturprofil - Teil 1: Klassifikation,
générales et méthodes d'essai allgemeine Anforderungen und Prüfungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 107.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17878-1:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17878-1:2022
prEN 17878-1:2022 (E)
Contents Page

European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and symbols . 7
3.1 Terms and definitions . 7
3.2 Symbols, indices and abbreviations . 7
4 Classification . 11
5
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.