This Technical Specification describes a method for sampling and determining the concentration of gaseous sulphur dioxide (SO2) emissions from stacks. This method is based on instrumental techniques. It is applicable to both periodic measurements and the calibration of automated measuring systems permanently installed on stacks, for regulatory or other purposes.

  • Technical specification
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification describes a method for sampling and determining the concentration of gaseous sulphur dioxide (SO2) emissions from stacks. This method is based on instrumental techniques. It is applicable to both periodic measurements and the calibration of automated measuring systems permanently installed on stacks, for regulatory or other purposes.

  • Technical specification
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This European Standard specifies:
-  a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation;
-  a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL1;
-  a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This European Standard is designed to be used after the AMS has been certified in accordance with the series of European Standards EN 15267.
This European Standard is restricted to quality assurance (QA) of the AMS, and does not include the QA of the data collection and recording system of the plant.

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This European Standard specifies:
-   a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation;
-   a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL1;
-   a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This European Standard is designed to be used after the AMS has been certified in accordance with the series of European Standards EN 15267.

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN ISO 16911-1 specifies a method for periodic determination of the axial velocity and volume flow rate of gas within emissions ducts and stacks. It is applicable for use in circular or rectangular ducts with measurement locations meeting the requirements of EN 15259. Minimum and maximum duct sizes are driven by practical considerations of the measurement devices described within EN ISO 16911-1. EN ISO 16911-1 requires all flow measurements to have demonstrable metrological traceability to national or international primary standards. To be used as a standard reference method, the user is required to demonstrate that the performance characteristics of the method are equal to or better than the performance criteria defined in EN ISO 16911-1 and that the overall uncertainty of the method, expressed with a level of confidence of 95 %, is determined and reported. The results for each method defined in EN ISO 16911-1 have different uncertainties within a range of 1 % to 10 % at flow velocities of 20 m/s. Methods further to these can be used provided that the user can demonstrate equivalence, based on the principles of CEN/TS 14793.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN ISO 16911-2 describes specific requirements for automated measuring system (AMS) flow monitoring. It is partly derived from EN 14181 which is the general document on the quality assurance of AMSs and is applicable in conjunction with that document. EN ISO 16911-2 specifies conditions and criteria for the choice, mounting, commissioning and calibration of AMSs used for determining the volume flow rate from a source in ducted gaseous streams. EN ISO 16911-2 is applicable by correlation with the manual reference methods described in EN ISO 16911-1. EN ISO 16911-2 is primarily developed for monitoring emissions from waste incinerators and large combustion plants. From a technical point of view, it can be applied to other processes for which flow rate measurement is required with a defined and minimized uncertainty.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16911-1:2013 specifies a method for periodic determination of the axial velocity and volume flow rate of gas within emissions ducts and stacks. It is applicable for use in circular or rectangular ducts with measurement locations meeting the requirements of EN 15259. Minimum and maximum duct sizes are driven by practical considerations of the measurement devices described within ISO 16911-1:2013.
ISO 16911-1:2013 requires all flow measurements to have demonstrable metrological traceability to national or international primary standards.
To be used as a standard reference method, the user is required to demonstrate that the performance characteristics of the method are equal to or better than the performance criteria defined in ISO 16911-1:2013 and that the overall uncertainty of the method, expressed with a level of confidence of 95 %, is determined and reported. The results for each method defined in ISO 16911-1:2013 have different uncertainties within a range of 1 % to 10 % at flow velocities of 20 m/s.
Methods further to these can be used provided that the user can demonstrate equivalence, based on the principles of CEN/TS 14793.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16911-2:2013 describes specific requirements for automated measuring system (AMS) flow monitoring. It is partly derived from EN 14181 which is the general document on the quality assurance of AMSs and is applicable in conjunction with that document.
ISO 16911-2:2013 specifies conditions and criteria for the choice, mounting, commissioning and calibration of AMSs used for determining the volume flow rate from a source in ducted gaseous streams. ISO 16911-2:2013 is applicable by correlation with the manual reference methods described in ISO 16911-1.
ISO 16911-2:2013 is primarily developed for monitoring emissions from waste incinerators and large combustion plants. From a technical point of view, it can be applied to other processes for which flow rate measurement is required with a defined and minimized uncertainty.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The method described in this European Standard determines the concentration of chlorinated compounds in a flue gas that - after passage of the sampling system including a particle filter - give Cl- ions in the absorption solution. This Standard Reference Method has been evaluated during field tests on waste incineration. The method applies to waste gases in which chlorides concentration expressed as HCl may vary between 1 mg-m-3 and 5 000 mg-m-3 under normal pressure and temperature conditions (see Note 1), and according to emission limit values laid down, for example, in the Council Directive 2000/76/EC on waste incineration plants.
NOTE 1 The limit values of this European Standard are expressed in mg HCl/m3, on dry basis, at the reference conditions of 273 K and 101,3 kPa and at the reference O2 concentration.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The method described in this European Standard determines the concentration of chlorinated compounds in a flue gas that - after passage of the sampling system including a particle filter - give Cl- ions in the absorption solution. This Standard Reference Method has been evaluated during field tests on waste incineration. The method applies to waste gases in which chlorides concentration expressed as HCl may vary between
1 mg m-3 and 5 000 mg m-3 under normal pressure and temperature conditions (see Note 1), and according to emission limit values laid down, for example, in the Council Directive 2000/76/EC on waste incineration plants.
NOTE 1   The limit values of this European Standard are expressed in mg HCl/m3, on dry basis, at the reference conditions of 273 K and 101,3 kPa and at the reference O2 concentration.
NOTE 2   The required uncertainty results from the capacity of the method tested in the field (Annex D) and in the laboratory (see performance characteristics in Tables 1 and 2 and Annex C).

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements for the manufacturer's quality management system, the initial assessment of the manufacturer's production control and the continuing surveillance of the effect of subsequent design changes on the performance of certified automated measuring systems. This European Standard also serves as a reference document for auditing the manufacturer's quality management system.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring ambient air quality and emissions from stationary sources. This product certification consists of the following sequential stages: a) performance testing of an automated measuring system; b) initial assessment of the AMS manufacturer's quality management system; c) certification; d) surveillance. This European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring ambient air quality and emissions from stationary sources. This product certification consists of the following sequential stages:
a)   performance testing of an automated measuring system;
b)   initial assessment of the AMS manufacturer’s quality management system;
c)   certification;
d)   surveillance.
This European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements for the manufacturer’s quality management system, the initial assessment of the manufacturer’s production control and the continuing surveillance of the effect of subsequent design changes on the performance of certified automated measuring systems.
This European Standard also serves as a reference document for auditing the manufacturer’s quality management system.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives recommendations and specifies requirements for the elaboration of standardised reference methods of measurement for the field of stationary source emissions by CEN/TC 264, with or without reference to accreditation. It aims at facilitating in the working groups the elaboration and the harmonisation of the standards produced by CEN/TC 264.
This document aims at ensuring that the specific requirements specified in CEN/TS 15675 are taken on board in the individual measurement standards either directly or by reference to EN 15259.
This document specifies terms and definitions for use in other air quality standards.
This document elaborates the CEN rules as given in CEN/BOSS and in the Internal Regulations Part 3 (PNE rules) in the field of stationary source emissions.

  • Technical specification
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives recommendations and specifies requirements for the elaboration of standardised reference methods of measurement for the field of stationary source emissions by CEN/TC 264, with or without reference to accreditation. It aims at facilitating in the working groups the elaboration and the harmonisation of the standards produced by CEN/TC 264.
This document aims at ensuring that the specific requirements specified in CEN/TS 15675 are taken on board in the individual measurement standards either directly or by reference to EN 15259.
This document specifies terms and definitions for use in other air quality standards.
This document elaborates the CEN rules as given in CEN/BOSS and in the Internal Regulations Part 3 (PNE rules) in the field of stationary source emissions.

  • Technical specification
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification supplements the requirements of EN ISO/IEC 17025:2005, and is suitable for the demonstration of competence of laboratories that undertake periodic measurement of emissions from stationary sources including
-   the taking of representative samples of emissions and subsequent laboratory analysis for gases and for particulate species,
-   the determination of reference quantities such as temperature, pressure, water vapour and oxygen content in the field and
-   the use of portable instruments (such as hand held instruments and transportable instruments used in mobile laboratories) in the field.
This Technical Specification is applicable to all laboratories undertaking the periodic measurement of emissions from stationary sources, the calibration of installed automated measuring systems in accordance with EN 14181:2004 and/or the field testing of automated measuring systems for conformity assessment purposes.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification supplements the requirements of EN ISO/IEC 17025:2005, and is suitable for the demonstration of competence of laboratories that undertake periodic measurement of emissions from stationary sources including
-   the taking of representative samples of emissions and subsequent laboratory analysis for gases and for particulate species,
-   the determination of reference quantities such as temperature, pressure, water vapour and oxygen content in the field and
-   the use of portable instruments (such as hand held instruments and transportable instruments used in mobile laboratories) in the field.
This Technical Specification is applicable to all laboratories undertaking the periodic measurement of emissions from stationary sources, the calibration of installed automated measuring systems in accordance with EN 14181:2004 and/or the field testing of automated measuring systems for conformity assessment purposes.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Amendments concerning definition, requirements, warning and rationale for small balls
This European Standard specifies requirements and methods of tests for mechanical and physical properties of toys. This European Standard applies to toys for children, toys being any product or material designed or clearly intended for use in play by children of less than 14 years. It refers to new toys taking into account the period of foreseeable and normal use, and that the toys are used as intended or in a foreseeable way, bearing in mind the normal behaviour of children. It includes specific requirements for toys intended for children under 36 months and for children who are too young to sit up unaided. For the purpose of this European Standard, soft-filled toys with simple features intended for holding and cuddling are considered as toys intended for children under 36 months. This European Standard also specifies requirements for packaging, marking and labelling. This European Standard does not cover musical instruments, sports equipment or similar items but does include their toy counterparts.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day