17.060 - Measurement of volume, mass, density, viscosity

This document specifies a method for the determination of the mass per unit area. It also specifies five
methods (Method A to Method E) for the determination of the fibre mass per unit area of moulding
compounds and prepregs. The five methods are as follows:
— Method A: Extraction by Soxhlet;
— Method B: Extraction by immersion in solvent in a beaker;
— Method C: Decomposition by loss ignition;
— Method D: Extraction by wet combustion;
— Method E: Method by calculation.
This document is ...view more

This Standard is applicable to full size thermal insulating products and test specimens. This standard can also be applied to the individual layers of multi layered products. It specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions.

ISO 80000-3:2019 gives names, symbols, definitions and units for quantities of space and time. Where appropriate, conversion factors are also given.

This document gives guidelines for determining the average surface density over a measured area
of anodic oxide or of a coating deposited autocatalytically, mechanically, by chemical conversion,
by electrodeposition, by hot dip galvanizing and by chemical or physical vapour deposition using
gravimetric and other chemical analysis procedures that have attained some degree of national or
international standardization.
A variety of procedures are described and include:
— gravimetric procedure...view more

This document specifies three methods for the determination of dry bulk density of soils calculated
from the mass and the volume of a soil sample. The methods involve drying and weighing a soil sample,
the volume of which is either known [core method (see 4.1)] or determined [excavation method (see 4.2)
and clod method (see 4.4)].

This part of IEC 61987 provides an
• operating list of properties (OLOP) for the description of the operating parameters and the
collection of requirements for a density measuring equipment, and
• device lists of properties (DLOP) for a range of density measuring equipment types
describing them.
The structures of the OLOP and the DLOP correspond with the general structures defined in
IEC 61987-11 and agree with the fundamentals for the construction of LOPs defined in
IEC 61987-10.
Aspect...view more

This document specifies a method for determining the absolute particle density of fine ceramic powders or sintered parts using liquid pycnometry.
NOTE Other pycnometer methods like gas pycnometers (e.g. helium pycnometer), where a gas is used as media, also exist.

This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction.
NOTE This test procedure is not intended to determine the absolute maximum value of loss of volume of a tested sealant, but it is an indicative measurement of the loss of volume under specified parameters.

This standard describes the method for determining the particle density of compressed fuels such as pellets or briquettes. Particle density is not an absolute value and conditions for its determination have to be standardised to enable comparative determinations to be made.

This document describes a method of determining bulk density of solid biofuels by the use of a standard measuring container. This method is applicable to all solid biofuels with a nominal top size of maximum 100 mm.
Bulk density is not an absolute value, therefore conditions for its determination have to be standandised in order to gain comparative measuring results.
Note 1: The nominal top size is defined as the aperture size of the sieve where at least 95 % by mass of the material passes (ISO ...view more

This European Standard sets out principles for the design of volumetric instruments manufactured from glass or from plastics in order to facilitate the most reliable and convenient use to the intended degree of accuracy.

ISO 384:2015 sets out principles for the design of volumetric instruments manufactured from glass or from plastics in order to facilitate the most reliable and convenient use to the intended degree of accuracy.

ISO 3819:2015 specifies requirements for an internationally acceptable series of glass beakers for laboratory use.

ISO 3819:2015 specifies requirements for an internationally acceptable series of glass beakers for laboratory use.

ISO 384:2015 sets out principles for the design of volumetric instruments manufactured from glass or from plastics in order to facilitate the most reliable and convenient use to the intended degree of accuracy.

The terminology used in this Standard conforms to the ?International Vocabulary of Basic and General Terms in Metrology? (VIM), the ?International Vocabulary of Terms in Legal Metrology? (VIML). In addition for the purposes of this Standard, the following definitions apply. An index of all the terms, 166 definitions and references defined below can be found under T.8.

This International Standard provides methods for the testing, calibration and use of volumetric instruments made from glass in order to obtain the best accuracy in use.
NOTE Testing is the process by which the conformity of the individual volumetric instrument with the appropriate standard is determined, culminating in the determination of its error of measurement at one or more points.
The International Standards for the individual volumetric instruments include clauses on the definition of c...view more

ISO 4787:2010 provides methods for the testing, calibration and use of volumetric instruments made from glass in order to obtain the best accuracy in use.
The International Standards for the individual volumetric instruments (ISO 385, ISO 646, ISO 835, ISO 1042 and ISO 4788) include clauses on the definition of capacity; these clauses describe the method of manipulation in sufficient detail to define the capacity without ambiguity. ISO 4787:2010 contains supplementary information.
The procedu...view more

ISO 4787:2010 provides methods for the testing, calibration and use of volumetric instruments made from glass in order to obtain the best accuracy in use. The International Standards for the individual volumetric instruments (ISO 385, ISO 646, ISO 835, ISO 1042 and ISO 4788) include clauses on the definition of capacity; these clauses describe the method of manipulation in sufficient detail to define the capacity without ambiguity. ISO 4787:2010 contains supplementary information. The procedures...view more

TC - Modifications in Clauses 2, 3, 6, C.1 and C.2.