25.080.40 - Drilling machines

IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented b...view more

This document specifies, with reference to ISO 230-1, geometrical tests on general purpose and normal accuracy box type vertical drilling machines. It also specifies the applicable tolerances corresponding to the above‐mentioned tests. This document deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.) or to machine characteristics (such as speeds, feeds, etc.), w...view more

IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented b...view more

2017-03-16 SW: DOW=DOR+24 m.

This part of IEC 62841 applies to transportable drills, with manually fed axial movement of
the spindle, having a maximum chuck capacity of 13 mm.
NOTE 101 Transportable drills are also known as bench drills or drill presses.
This part of IEC 62841 does not apply to stationary drilling machines.
This part of IEC 62841 does not apply to radial arm drills.
This part of IEC 62841 does not apply to magnetic drill stands and drill motors.
NOTE 102 Magnetic drill stands and drill motors will be ...view more

EN 16228-3, together with part 1, deals with all significant hazards for horizontal directional drilling equipment (HDD) when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4). The requirements of this part are complementary to the common requirements formulated in EN 16228-1:2014.

EN IEC 62841-3-6 applies to transportable diamond drills, intended to be connected to a liquid system. Liquid system may include liquid from a pipe or container.

EN 16228-2, together with part 1, deals with all significant hazards for mobile drill rigs for civil and geotechnical engineering, quarrying and mining when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4). In this document the general term “mobile drill rig” covers several different types of machines for use in: - civil engineering; - geotechnical engineering (inclu...view more

This clause of Part 1 is applicable except as follows:
1.1 Addition:
This standard applies to transportable diamond drills manually fed, intended to be connected to a water supply (water supply may include water source from a pipe or tank or vat).

This clause of Part 1 is applicable,  except as follows: Addition: This  standard applies to drills and impact  drills.

This European Standard contains the requirements for stationary machines for the drilling of flat glass, using a powered rotating tool. Stationary machines are classified into: a) manual; b) semi-automatic; c) automatic single-head or multi-head; d) fully automatic. This European Standard deals with the significant hazards, hazardous situations and events relevant to drilling machines for flat glass when they are used as intended and under the conditions of misuse which are reasonably foreseeabl...view more

This amendment enables EN 60745-2-1 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-1:2010

This European Standard applies to core drilling machines on transportable stands equipped with a diamond core drill bit, usually with a water supply connection device, and intended to drill holes into stone, concrete and similar mineral materials in a stationary position where the power for the tool rotation is supplied by an electrical, hydraulic, pneumatic or internal combustion prime motor.
The feed movement of the drill head and core drill bit may be effected by manual, mechanical or hydrau...view more

This European Standard applies to core drilling machines on transportable stands equipped with a diamond
core drill bit, usually with a water supply connection device, and intended to drill holes into stone, concrete and
similar mineral materials in a stationary position where the power for the tool rotation is supplied by an
electrical, hydraulic, pneumatic or internal combustion prime motor.
The feed movement of the drill head and core drill bit may be effected by manual, mechanical or hyd...view more

1.1   This standard specifies the technical safety requirements and measures to be adopted by persons undertaking the design, construction and supply (including installation and dismantling, with arrangements for transport and maintenance) of stationary drilling machines (see 3.1).
This standard covers both manual and automatic drilling machines. These include but are not limited to:
-   pedestal drilling machines (see figure A.1);
-   radial arm drilling machines (see figure A.2);
-   coordinate ta...view more

1.1   This standard specifies the technical safety requirements and measures to be adopted by persons undertaking the design, construction and supply (including installation and dismantling, with arrangements for transport and maintenance) of stationary drilling machines (see 3.1).
This standard covers both manual and automatic drilling machines. These include but are not limited to:
-   pedestal drilling machines (see figure A.1);
-   radial arm drilling machines (see figure A.2);
-   coordinate ta...view more

Superseded by EN 60745-2-1:2010

To be read with EN 60745-1:2003 * Supersedes EN 50144-2-1:1999 and EN 50260-2-1:2002