25.160.01 - Welding, brazing and soldering in general

This document outlines the equipment and operator qualification needed for laser-arc hybrid welding, and recommends butt, fillet and flange joint preparations and consumables suitable for use with this process. It also gives an overview of the steps to take during equipment set-up, procedure specification, workpiece set-up immediately prior to welding, and after welding once inspecting and testing the welds. This document applies to laser-arc hybrid welding of steels, aluminium and its alloys. T...view more

This document specifies requirements for the qualification of welding operators for friction stir welding (FSW) of aluminium. In this document, the term "aluminium" refers to aluminium and its alloys. This document does not apply to "operators" as defined in ISO 25239‑1. This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

This document specifies requirements for the qualification of welders and welding operators for the fusion welding of metallic materials for aerospace applications.
NOTE Success in the test is an essential precondition for the qualification of welders (3.2) and welding operators (3.3) in new production and repair work in aerospace. However, welding equipment operators (3.4) do not need to be qualified according to this document.

This document defines two levels of quality requirements and selection criteria for brazing of metallic materials. It applies to manufacturing, both in workshops and at installation sites. NOTE 1 This document is applicable to brazing industry quality management systems, similar in scope and purpose to the ISO 3834 series. This document provides complete sets of quality requirements for process control related to all listed brazing processes (for each process separately or in combination as spec...view more

This document specifies acceptance criteria for fusion weldments on metallic components. It is to be applied provided it is referenced or approved by the responsible engineering/design authority. This document covers the following processes given in Table 1 and the material groups given in Table 2.

This document specifies the requirements for fusion welding of aerospace hardware. It is to be used in conjunction with the design/engineering authority's design documents or their accepted data. This document covers the processes given in Table 1 and material groups given in Table 2.

This document specifies two methods for establishing the minimum air volume flow rate. One method is dedicated for use with captor hoods, nozzles and slot nozzles with a ratio of slot length to hose diameter of 8:1 or less. The other method is dedicated for use with on-gun extraction devices.
These methods are not applicable to down draught tables.

This document specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements.
The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used.
This document applies to equipment that is manufactured after its publication.
NOTE General ventilation systems are excluded from the Scope of ISO 21904-1.

This document defines the general requirements for ventilation equipment used to capture and separate fumes generated by welding and allied processes, e.g. arc welding and thermal cutting.
This document also specifies the test data to be marked on the capture devices.
It applies to the design and manufacture of parts of the equipment including hoods for welding, ducting, filter units, air movers, systems that inform of unsafe operation and workplace practices to ensure safe working with regard...view more

This document specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements. The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used. This document applies to equipment that is manufactured after its publication. NOTE General ventilation systems are excluded from the Scope of ISO 21904-1.

This document defines the general requirements for ventilation equipment used to capture and separate fumes generated by welding and allied processes, e.g. arc welding and thermal cutting. This document also specifies the test data to be marked on the capture devices. It applies to the design and manufacture of parts of the equipment including hoods for welding, ducting, filter units, air movers, systems that inform of unsafe operation and workplace practices to ensure safe working with regard t...view more

This document provides a grouping system for American parent materials for brazing.

This document identifies the essential welding quality related tasks and responsibilities included in welding coordination.
The principle of an assessment according to this document is that welding coordination personnel need to be competent in the welding-related tasks allocated to them.
It is presumed that welding coordination personnel have the necessary education, qualifications and experience and are appointed by the manufacturer.
Regulatory documents, application standards and contracts...view more

This document identifies the essential welding quality related tasks and responsibilities included in welding coordination. The principle of an assessment according to this document is that welding coordination personnel need to be competent in the welding-related tasks allocated to them. It is presumed that welding coordination personnel have the necessary education, qualifications and experience and are appointed by the manufacturer. Regulatory documents, application standards and contracts ca...view more

This document specifies requirements for the qualification of welders and welding operators for the fusion welding of metallic materials for aerospace applications. NOTE Success in the test is an essential precondition for the qualification of welders (3.2) and welding operators (3.3) in new production and repair work in aerospace. However, welding equipment operators (3.4) do not need to be qualified according to this document.

This document specifies the requirements for the qualification of welding personnel for friction stir spot welding (FSSW) of aluminium. In this document, the term "aluminium" refers to aluminium and its alloys. This document does not apply to personnel exclusively performing loading or unloading of the automatic welding unit.

This document specifies the qualification requirements for personnel performing micro-joining and oxygenation anneling, and testing the 2G HTS test joints.

This document provides concepts, specification and qualification of 2G HTS joining procedure. A welding procedure specification (WPS) is needed to provide a basis for planning joining operations and for quality control during joining. Joining is considered as a special process in the terminology of standards for quality systems. Standards for quality systems usually require that special processes be carried out in accordance with written procedure specifications. This has resulted in the establi...view more

This document specifies the qualification requirements for personnel performing micro-joining and oxygenation anneling, and testing the 2G HTS test joints.

This document provides concepts, specification and qualification of 2G HTS joining procedure. A welding procedure specification (WPS) is needed to provide a basis for planning joining operations and for quality control during joining. Joining is considered as a special process in the terminology of standards for quality systems. Standards for quality systems usually require that special processes be carried out in accordance with written procedure specifications. This has resulted in the establi...view more