29.100 - Components for electrical equipment
ICS 29.100 Details
Components for electrical equipment
Bauteile fur elektrische Gerate
Composants pour materiel electrique
Komponente za električne naprave
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 29.100 - Components for electrical equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
- Draft45 pagesEnglish languagesale 10% offe-Library read for1 day
This standard provides the test methods for the electrical and magnetic properties of magnetic powder cores used for inductive components in electronics equipment, switch-mode power supplies and power conversion equipment, and introduces measuring principles, scope of application and matters needing attention for each method. The parameters used to characterize the magnetic powder cores include: inductance factor, effective permeability, complex relative permeability, temperature coefficient of permeability, frequency coefficient of permeability, DC bias characteristic, power loss, and quality factor. This standard is the basis for determining the characteristic parameters of magnetic powder cores.
- Draft45 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62044-3:2023 is available as IEC 62044-3:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62044-3:2023 specifies measuring methods for power loss and amplitude permeability of magnetic cores forming the closed magnetic circuits intended for use at high excitation levels in inductors, chokes, transformers and similar devices for power electronics applications. This second edition cancels and replaces the first edition published in 2000. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: addition of Annex F and Annex G.
- Standard93 pagesEnglish and French languagesale 15% off
IEC 63300:2023 provides the test methods for the electrical and magnetic properties of magnetic powder cores used for inductive components in electronics equipment, switch-mode power supplies and power conversion equipment, and introduces measuring principles, scope of application and matters of importance for each method.
The parameters used to characterize the magnetic powder cores include: inductance factor, effective permeability, complex relative permeability, temperature coefficient of permeability, frequency coefficient of permeability, DC bias characteristic, power loss, and quality factor. This document is the basis for determining the characteristic parameters of magnetic powder cores.
- Standard111 pagesEnglish and French languagesale 15% off
IEC 62321-3-4:2023 specifies procedures for the screening of di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) in polymers of electrotechnical products by using high performance liquid chromatography with ultraviolet detector (HPLC-UV), thin layer chromatography (TLC) and thermal desorption mass spectrometry (TD-MS).
High performance liquid chromatography with ultraviolet detector (HPLC-UV), thin layer chromatography (TLC) and thermal desorption mass spectrometry (TD-MS) techniques are described in the normative part of this document. Fourier transform infrared spectroscopy (FT-IR) is described in the informative annexes of this document.
- Standard107 pagesEnglish and French languagesale 15% off
IEC 62321-12:2023 specifies a reference test method for the simultaneous determination of polybrominated biphenyls, polybrominated diphenyl ethers, and four phthalates: di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) in polymers of electrotechnical products. The extraction technique described in this document is the ultrasonic-assisted extraction used for simultaneous extraction for sample preparation. Gas chromatography-mass spectrometry (GC-MS) is considered as the reference technique for the measurement of the simultaneous determination of analytes in the range of 25 mg/kg to 2 000 mg/kg. The test method using ultrasonic-assisted extraction followed by GC-MS detection has been evaluated by the tests of polypropylene (PP), polyvinylchloride (PVC), acrylonitrile butadiene styrene (ABS), acrylate rubber (ACM), polystyrene (PS), polyurethane (PU) and polyethylene (PE) materials. This document has the status of a horizontal publication in accordance with IEC Guide 108.
- Draft35 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-10:2022 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PM-cores made of magnetic oxides, the main dimensions for coil formers to be used with these cores and the locations of their pins on a modular printed wiring grid in relation to the base outlines of cores. It also specifies the effective parameter values to be used in calculations and gives guidelines on allowable limits of surface irregularities applicable to the PM-cores.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63182-5:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives the guidelines on allowable limits of surface irregularities for cylinder-cores made of metallic magnetic powder.
This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62321-12:2023 specifies a reference test method for the simultaneous determination of polybrominated biphenyls, polybrominated diphenyl ethers, and four phthalates: di-isobutyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) in polymers of electrotechnical products.
The extraction technique described in this document is the ultrasonic-assisted extraction used for simultaneous extraction for sample preparation.
Gas chromatography-mass spectrometry (GC-MS) is considered as the reference technique for the measurement of the simultaneous determination of analytes in the range of 25 mg/kg to 2 000 mg/kg.
The test method using ultrasonic-assisted extraction followed by GC-MS detection has been evaluated by the tests of polypropylene (PP), polyvinylchloride (PVC), acrylonitrile butadiene styrene (ABS), acrylate rubber (ACM), polystyrene (PS), polyurethane (PU) and polyethylene (PE) materials.
This document has the status of a horizontal publication in accordance with IEC Guide 108.
- Standard75 pagesEnglish and French languagesale 15% off
IEC 60456:2010 specifies methods for measuring the performance of clothes washing machines for household use, with or without heating devices utilising cold and/or hot water supply. It also deals with appliances for water extraction by centrifugal force (spin extractors) and is applicable to appliances for both washing and drying textiles (washer-dryers) with respect to their washing related functions. This International Standard also covers washing machines which specify the use of no detergent for normal use. This edition includes the following significant changes from the previous edition.
- modified test load mass requirement for cases where rated capacity of test machine is not declared;
- introduction of soft water option;
- expanded stain/soil set;
- improved method of loading and folding test load items to better suit vertical axis, horizontal axis and twin tub systems;
- revised and amended reference machine specifications reflecting full qualification on new Electrolux Wascator CLS;
- new reference programmes for lower temperature and vertical axis systems;
- refined rinsing efficiency method;
- introduction of low power modes "OFF" and "Left On";
- new annex regarding uncertanity of measurements.
- Standard608 pagesEnglish and French languagesale 15% off
- Standard300 pagesEnglish and French languagesale 15% off
IEC 61535:2019 is available as IEC 61535:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61535:2019 applies to two-wire, up to five-wire installation couplers, including earth, if provided, with a rated voltage up to and including 500 V AC or DC and a rated connecting capacity up to and including 10 mm2 for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This second edition cancels and replaces the first edition published in 2009 and Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - enlargement of the scope to DC application; - addition of further requirements as regards DC application (marking, etc.), no additional test procedures were deemed necessary; however some modifications were necessary in the normative text; - changes and enhancement of the field of application of installation couplers into outdoor applications; - addition of a suitable temperature range; - updating of the list of normative references, modified to undated references, where possible.
- Standard57 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft52 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies classification rules for metallic magnetic powder cores used in
inductive components fulfilling the requirements of the electronics industries.
This document addresses the following objectives for magnetic powder cores suppliers and
users:
– cross-reference between core materials from multiple suppliers;
– assistance to users in understanding the published technical data in catalogues when
comparing multiple suppliers;
– guidance to users in selecting the most applicable core for each application;
– establishing uniform benchmarks for suppliers for performance in the new development of
core material.
The numerical values given in this document are typical values of parameters of the related
material. Direct translation from the material specification into the core specification is not
always easy or possible.
Every detailed material and core specification will be agreed upon between the user and the
supplier.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC TS 62474-1:2022 is a guidance document to help organizations properly implement IEC 62474. These organizations can be the ones creating tools for material data exchange and those who submit and receive material declarations.
This document supports consistent implementation of IEC 62474, including how the procedures, content, and form relating to material declarations for products can be further specified. It also illustrates how to apply IEC 62474 to non-electrotechnical industries.
This document:
• illustrates the flexibility and functionality of the IEC 62474 standard including examples,
• illustrates how to achieve conformity with IEC 62474, including guidance on preparing a declaration for compliance and a composition declaration, including mandatory and optional declaration requirements,
• illustrates how IEC 62474 can be applied to non-electrotechnical industries by preparing material declarations using an alternate declarable substance list (DSL),
• supports organizations that create software to exchange substance and material data to implement IEC 62474 in their tools, and
• supports users that submit and receive material declarations.
Following the IEC 62474 standard scope, process chemicals, emissions during product use and product packaging material are not in the scope of this document.
IEC TS 62474-1:2022 cancels and replaces IEC TR 62474-1:2015.
This edition includes the following significant technical changes with respect to IEC TR 62474-1:2015:
a) IEC TR 62474-1:2015 was revised and converted to a Technical Specification in accordance with the requirements of the ISO/IEC Directives;
b) the introduction and scope have been updated to better align with the requirements of IEC 62474:2018;
c) by defining an authority, list identity and list version, the standard data exchange format can be used for lists other than the IEC 62474 database;
d) two types of material declarations, declaration for compliance and composition declaration, and their requirements are defined;
e) the material classes and exemption list capabilities have been improved;
f) guidance is provided on how to use data fields in the declaration of compliance and composition declaration to collect the information required for the European Chemical Agency (ECHA) Substances of Concern In articles, as such or in complex objects (Products) (SCIP) database;
g) six examples of material declaration are given to show how IEC 62474 meets various industry needs.
- Technical specification85 pagesEnglish languagesale 15% off
IEC 62025-2:2019 is available as IEC 62025-2:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62025-2:2019 specifies a test method for the non-electrical characteristics of the surface mounted device (SMD) inductors to be used for electronic and telecommunication equipment. The object of this part of this document is to define methods for measuring mechanical performance only. As the reliability performances and specifications relative to non-electrical performances are defined in IEC 62211, detailed measuring methods for mechanical performance of reliability testing are defined in this document. This edition includes the following significant technical changes with respect to the previous edition: - revision of Table 5; - revision of normative references.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63299:2022 specifies classification rules for metallic magnetic powder cores used in inductive components fulfilling the requirements of the electronics industries. This document addresses the following objectives for magnetic powder cores suppliers and users: - cross-reference between core materials from multiple suppliers; - assistance to users in understanding the published technical data in catalogues when comparing multiple suppliers; - guidance to users in selecting the most applicable core for each application; - establishing uniform benchmarks for suppliers for performance in the new development of core material.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60276:2018 applies to carbon brushes for electrical machinery. This edition applies only to carbon brushes for commutators and slip-rings in rotating machines. Terms and definitions are relative to the brush construction (references 100’s to 500’s and parts of 900’s) and to the markings when operating on a rotating machine (references 600’s to 800’s). This new edition includes the following significant technical changes with respect to the previous edition: Some nomenclature has been deleted or added, whereas remaining definitions have been detailed and clarified, to reflect the technical evolution since 1987. Additional definitions have been included to address the request for reviewing this standard, in particular nomenclature of commutator/slip-rings markings, brush markings and commutation sparks codes.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63299:2022 specifies classification rules for metallic magnetic powder cores used in inductive components fulfilling the requirements of the electronics industries. This document addresses the following objectives for magnetic powder cores suppliers and users:
- cross-reference between core materials from multiple suppliers;
- assistance to users in understanding the published technical data in catalogues when comparing multiple suppliers;
- guidance to users in selecting the most applicable core for each application;
- establishing uniform benchmarks for suppliers for performance in the new development of core material.
- Standard23 pagesEnglish and French languagesale 15% off
IEC 61333:2019 specifies marking locations and a coding system of marking on ferrite cores. An alphanumerical marking printed or attached to cores reduces the risk of incorrect assembly, mixing of materials and/or mixing of gapped cores on an assembly line. The markings of the inductance factor AL value or of the gap length are especially important to avoid this kind of problem, and their coding system is specified in this document. This edition includes the following significant technical changes with respect to the previous edition： a) the title of the document was changed; b) the scope of this document was expanded; c) the marking position instructions for ring cores, planar cores, RM-cores, PQ-cores and pot-cores were added in Clause 4 with a few additional descriptions; d) the four-digit-maximum limit of material identification code has been deleted in 5.2; e) in Table 1, the unit of AL has been changed from "nH" to "nH/N2".
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-10:2022 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PM-cores made of magnetic oxides, the main dimensions for coil formers to be used with these cores and the locations of their pins on a modular printed wiring grid in relation to the base outlines of cores. It also specifies the effective parameter values to be used in calculations and gives guidelines on allowable limits of surface irregularities applicable to the PM-cores.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for1 day
La présente partie de l’IEC 63093 spécifie les dimensions qui présentent une importance pour l'interchangeabilité mécanique d'une plage préférentielle de noyaux EFD, les dimensions essentielles des supports de bobine à utiliser avec les noyaux EFD, ainsi que les valeurs des paramètres effectifs à utiliser dans les calculs qui impliquent ces noyaux. Elle donne également des recommandations relatives aux limites admissibles des irrégularités de surface applicables aux noyaux EFD conformément à la spécification générique correspondante. Le choix des tailles des noyaux pour le présent document est fondé sur la philosophie consistant à introduire les tailles qui correspondent à des normes industrielles, soit par inclusion dans des normes nationales, soit par utilisation à grande échelle dans l’industrie. Le présent document est une spécification utile à la négociation entre les fabricants et les utilisateurs de noyaux ferrites sur les irrégularités de surface. Les considérations générales sur lesquelles repose la conception de cette plage de noyaux figurent dans l’Annexe A.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63093 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of ring-cores, also called toroid cores, and the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to ring-cores. This document is a specification useful in the negotiations between ferrite core manufacturers and users about surface irregularities.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-10:2022 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PM-cores made of magnetic oxides, the main dimensions for coil formers to be used with these cores and the locations of their pins on a modular printed wiring grid in relation to the base outlines of cores. It also specifies the effective parameter values to be used in calculations and gives guidelines on allowable limits of surface irregularities applicable to the PM-cores.
- Standard40 pagesEnglish and French languagesale 15% off
IEC 63093-4:2019 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of RM-cores and low-profile RM-cores made of ferrite, and the locations of their terminal pins on a 2,54 mm printed wiring grid in relation to the base outlines of the cores. It also gives guidance on allowable limits of surface irregularities applicable to RM-cores in accordance with the relevant generic specification. The selection of core sizes for this document is based on the philosophy of including those sizes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry. This document is a specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities. This first edition cancels and replaces the first edition of IEC 62317-4 published in 2005 and the second edition of IEC 60424-2 published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 62317-4:2005 and IEC 60424-2:2015: a) IEC 63093-4 integrates the contents of IEC 62317-4:2005 and IEC 60424-2:2015; b) IEC 60424-2:2015, Table 2, has been included in Annex C as Table C.1.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63182 specifies the dimensions that are of importance for mechanical
interchangeability for a preferred range of E-cores made of metallic magnetic powder, the
essential dimensions of coil formers to be used with them as well as the effective parameter
values to be used in calculations involving them, and gives guidelines on allowable limits of
surface irregularities applicable to E-cores.
This document is a specification useful in the negotiations between magnetic powder core
suppliers and users about surface irregularities.
The use of "derived" standards which give more detailed specifications of component parts
while still permitting compliance with this document is discussed in Annex A.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft12 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63093 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of PQ-cores and low-profile PQI-cores made of ferrite, and the locations of their terminal pins on a 2,54 mm printed wiring grid in relation to the base outlines of the cores. It also gives guidance on allowable limits of surface irregularities applicable to PQ-cores in accordance with the relevant generic specification. The selection of core sizes for this document is based on the philosophy of including those sizes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry. This document is a specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities. The general considerations that the design of this range of cores is based upon are given in Annex A.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63182-3:2021 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of E-cores made of metallic magnetic powder, the essential dimensions of coil formers to be used with them as well as the effective parameter values to be used in calculations involving them, and gives guidelines on allowable limits of surface irregularities applicable to E-cores. This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft12 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63182 specifies the preferred range of the dimensions that are important for mechanical interchangeability and the guidelines on allowable limits of surface irregularities for block-cores made of metallic magnetic powder.
This document is a specification about surface irregularities which is useful in the negotiations between suppliers and users of magnetic powder core.
The use of "derived" standards which give more detailed specifications of component parts while still permitting compliance with this standard is discussed in Annex A.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63182 specifies the preferred range of the dimensions that are important for mechanical interchangeability and the guidelines on allowable limits of surface irregularities for block-cores made of metallic magnetic powder. This document is a specification about surface irregularities which is useful in the negotiations between suppliers and users of magnetic powder core. The use of "derived" standards which give more detailed specifications of component parts while still permitting compliance with this standard is discussed in Annex A.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63182-5:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives the guidelines on allowable limits of surface irregularities for cylinder-cores made of metallic magnetic powder. This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment10 pagesEnglish languagesale 10% offe-Library read for1 day
NEW!IEC 60730-2-14:2017 is available as IEC 60730-2-14:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60730-2-14:2017 applies to electric actuators for use in, on, or in association with equipment for household and similar use. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof. This International Standard is applicable to controls for building automation within the scope of ISO 16484. This part 2-14 also applies to automatic electrical controls for equipment that may be used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications. EXAMPLE Controls for commercial catering, heating and air-conditioning equipment. Electric actuators for appliances are within the scope of IEC 60335. This second edition cancels and replaces the first edition, published in 1995, its Amendment 1 (2001) and its Amendment 2 (2007). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: adapting it to the 5th Ed of IEC 60730-1, addition of checking electric actuators with action 1.AB or 2AB, and modification of tests under abnormal condition. This Part 2-14 is intended to be used in conjunction with IEC 60730-1. It was established on the basis of the 5th edition of that standard (2013). Consideration may be given to future editions of, or amendments to, IEC 60730-1. This part 2-14 supplements or modifies the corresponding clauses in IEC 60730-1, so as to convert that publication into the IEC standard: Particular requirements for electric actuators. Where this part 2-14 states "addition", "modification" or "replacement", the relevant requirement, test specification or explanatory matter in part 1 should be adapted accordingly. Where no change is necessary part 2-14 indicates that the relevant clause or subclause applies. Key words: Automatic Controls, Electric Actuators
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the procedure, content, and form relating to material declarations for products and accessories of organizations operating in and supplying to the electrotechnical industry. Process chemicals, emissions during product use and product packaging material are not in the scope of this document. The main intended use of this document is to provide data up and down the supply chain that: - allows organizations to assess products against substance compliance requirements, - allows organizations to use this information in their environmentally conscious design process and across all product life cycle phases. This document specifies mandatory declaration requirements and also provides optional declaration requirements. This document does not suggest any specific method or process to capture material declaration data in the supply chain. However, it provides a data format used to transfer information within the supply chain. Organizations have the flexibility to determine the most appropriate method to capture material declaration data without compromising data utility and quality. This document is intended to allow reporting based on engineering judgement, supplier material declarations, and/or sampling and testing.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
IEC corrected version
- Corrigendum4 pagesEnglish and French languagesale 10% offe-Library read for1 day
- Amendment10 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63182-5:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives the guidelines on allowable limits of surface irregularities for cylinder-cores made of metallic magnetic powder.
This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.
- Standard20 pagesEnglish and French languagesale 15% off
IEC 63182-4:2021 specifies the preferred range of the dimensions that are of importance for mechanical interchangeability and gives guidelines on allowable limits of surface irregularities for block-cores made of metallic magnetic powder.
This document is a specification about surface irregularities which is useful in the negotiations between suppliers and users of magnetic powder-cores.
- Standard17 pagesEnglish and French languagesale 15% off
IEC corrected version
- Corrigendum4 pagesEnglish and French languagesale 10% offe-Library read for1 day
IEC 63093-8:2018(E) specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of E-cores made of ferrite and the essential dimensions of coil formers to be used with them, as well the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to E-cores. The specifications contained in this document are useful in negotiations between ferrite core manufacturers and customers about surface irregularities. The use of derived standards, which give more detailed specifications of component parts while still permitting compliance with this standard, is discussed in Annex A. This edition includes the following significant technical changes with respect to IEC 62317-8:2006 and IEC 60424-3:2015: a. This document integrates IEC 62317-8:2006 and IEC 60424-3:2015; b. Table 4 – Allowable areas of chips for E-cores, of IEC 60424-3:2015, has been moved to Annex C (informative) of this document.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-6:2018(E) specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of ETD-cores made of ferrite and the essential dimensions of coil formers to be used with them, as well the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to ETD-cores. The specifications contained in this document are useful in negotiations between ferrite core manufacturers and users about surface irregularities. The use of derived standards which give more detailed specifications of component parts while still permitting compliance with this document is discussed in REF _Ref506796608 \r \h Annex A 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000E0000005F005200650066003500300036003700390036003600300038000000 . This edition includes the following significant technical changes with respect to IEC 62317-6:2015 and IEC 60424-3:2015: a. This document integrates IEC 62317-6:2015 and IEC 60424-3:2015; b. Table 1 – Allowable areas of chips for ETD-cores, of IEC 60424-3:2015, has been moved to Annex C (informative) of this document.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60938 applies to fixed inductors designed for electromagnetic interference suppression, which will be connected to an AC mains or other supply with a nominal voltage not exceeding 1 000 V AC RMS or 1 500 V DC with a nominal frequency not exceeding 400 Hz. This sectional specification is restricted to fixed inductors for which safety tests are appropriate. This implies that inductors specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Annex A is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. The object of this document is to prescribe standard requirements for safety tests, preferred ratings and characteristics, to select from IEC 60938-1 the appropriate methods of test and to give general performance requirements for suppression inductors.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-5:2018(E) specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EP-cores made of ferrite, the essential dimensions of coil formers to be used with them and the locations of their terminal pins on a 2,50 mm printed wiring grid in relation to the base outlines of the cores and the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to EP-cores. The specifications contained in this document are useful in negotiations between ferrite core manufacturers and users about surface irregularities. The general considerations upon which the design of this range of cores is based are as given in Annex A. This edition includes the following significant technical changes with respect to IEC 62317-5:2015: a. addition of the limits of surface irregularities.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard applies to inductors designed for electromagnetic interference suppression intended for use within all kind of electric and electronic equipment. In this Generic Specification normative reference, terms and definitions are given. It also prescribes General requirements and the suitable test and measurement procedures for interference suppression inductors.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-11:2018(E) specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EC-cores made of ferrite and the essential dimensions of coil formers to be used with them, as well the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to EC-cores. The specifications contained in this document are useful in negotiations between ferrite core manufacturers and customers about surface irregularities. This first edition cancels and replaces the first edition of IEC 62317-11 published in 2015 and the second edition of IEC 60424-3 published in 2015. This edition constitutes a technical revision. This document includes the following significant technical changes with respect to IEC 6231711:2015 and IEC 60424-3:2015: This document integrates IEC 62317-11:2015 and IEC 604243:2015; Table 3 – Allowable areas of chips for EC-cores, of IEC 60424-3:2015, has been moved to Annex B (informative) of this document.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
2021-06-11 - IEC Corrected version
- Corrigendum4 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60938-2:2021 applies to fixed inductors designed for electromagnetic interference suppression, which will be connected to an AC mains or other supply with a nominal voltage not exceeding 1 000 V AC RMS or 1 500 V DC with a nominal frequency not exceeding 400 Hz.
This sectional specification is restricted to fixed inductors for which safety tests are appropriate. This implies that inductors specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Annex A is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required.
The object of this document is to prescribe standard requirements for safety tests, preferred ratings and characteristics, to select from IEC 60938-1 the appropriate methods of test and to give general performance requirements for suppression inductors.
This edition includes the following significant technical changes with respect to the previous edition:
- the test plan for performance testing has been removed; mandatory safety tests and optional performance tests are listed in one test plan in Annex B;
- requirements for Thyristor-Chokes have been withdrawn;
- material requirements are harmonized with IEC 60939-3 and UL 60939-3;
- AC chokes up to 1 000 V and DC chokes up to 1 500 V are now in the Scope.
- Standard70 pagesEnglish and French languagesale 15% off
IEC 60938-1:2021 applies to inductors designed for electromagnetic interference suppression intended for use within all kind of electric and electronic equipment.
In this generic specification, normative references and terms and definitions are given. It also prescribes general requirements and the suitable test and measurement procedures for interference suppression inductors. Annex B states special requirements for earth inductors.
This edition includes the following significant technical changes with respect to the previous edition:
a) material tests added;
b) improved readability and clear separation between test descriptions in the generic spec and requirements in the sectional specification;
c) creepage and clearance requirements are now defined in sectional specifications only;
d) AC testing for voltage test included.
- Standard61 pagesEnglish and French languagesale 15% off
2021-06-11 - IEC Corrected version
- Corrigendum4 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-2:2020 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of pot-cores made of ferrite, and the dimensional limits for coil formers to be used with them, as well as the effective parameter values to be used in calculations involving them. It also gives guidelines on the allowable limits of surface irregularities applicable to pot-cores in accordance with the relevant generic specification.
The selection of core sizes and shapes for this document is based on the philosophy of including those sizes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry. See IEC 62317-1 for more detail concerning the philosophy of selecting core sizes to be included.
The general considerations upon which the design of this range of cores is based are given in Annex A.
This first edition cancels and replaces the first edition of IEC 62317-2 published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition of IEC 62317-2:
a) addition of the limits of surface irregularities;
b) Table 4 and Table 5 are updated in accordance with IEC 60205:2016.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63093-3:2020 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of half pot-cores made of ferrite, intended to be used in inductive proximity switches. Half pot-cores for inductive proximity switches are also called PS-cores.
The selection of core sizes and shapes for this document is based on the philosophy of including those sizes and shapes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry.
This part of IEC 63093 can also be considered as a sectional specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities. It provides guidelines on the allowable limits of surface irregularities applicable to PS-cores in accordance with the relevant generic specification.
This first edition cancels and replaces the first edition of IEC 62323, published in 2005. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition of IEC 62323:
a) addition of the limits surface irregularities.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61333:2019 specifies marking locations and a coding system of marking on ferrite cores. An alphanumerical marking printed or attached to cores reduces the risk of incorrect assembly, mixing of materials and/or mixing of gapped cores on an assembly line. The markings of the inductance factor AL value or of the gap length are especially important to avoid this kind of problem, and their coding system is specified in this document.
This edition includes the following significant technical changes with respect to the previous edition：
a) the title of the document was changed;
b) the scope of this document was expanded;
c) the marking position instructions for ring cores, planar cores, RM-cores, PQ-cores and pot-cores were added in Clause 4 with a few additional descriptions;
d) the four-digit-maximum limit of material identification code has been deleted in 5.2;
e) in Table 1, the unit of AL has been changed from "nH" to "nH/N2".
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day