29.140.99 - Other standards related to lamps

2020-08-05 NEXT ACTION: CCMC action by 2020-08-31
2020-08-03 CCMC to prepare request for BT
2020-08-03 since no 2nd assessment allowed, EC confirmed that TC met requirements for pos. ass.  
2019-02-20 PC: "lack of compliance" for LVD, TC to adress comments
2019-01-30 PC: Sent for LVD assessment
2018-03-22 - missing Annex ZZ - on hold
2017-10-05 - Cannot allocate for publication due to missing assessment from Consultant.

IEC TS 63105:2021(E) establishes terms and definitions in the field of lighting systems and related equipment.
Terminological literature for other fields of lighting is listed in the bibliography.

IEC PAS 63228:2020(E) This Book 12 defines LED Arrays with a rectangular shape and a circular light emitting surface. For each LED Array, this Book 12 also defines the mechanical interface between the LED Array and the corresponding Holder. The mechanical interface between the Holder and the Luminaire (e.g. outline, OCA and mounting holes) is defined in [Book-10]. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. In addition, this Book 1 specifies general ...view more

IEC PAS 63329:2020(E) This Book 14 defines three socketable LED Light Engines (with integrated Electronic Control Gears) and three socketable LED Modules (without integrated Electronic Control Gears). These LED Modules and LLEs have a rectangular shape and are typically applied in general lighting applications. These products are intended to be installed and replaced by professionals and non-professionals. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. ...view more

IEC PAS 63324:2020(E) This Book 10 defines interfaces between LED Modules, associate components (Holders) and luminaires. Not all interface descriptions are applicable to LED Modules or Holders, but where applicable they are identical. This Book 1 defines the common concepts that underlie the Zhaga interface specifications. In addition, this Book 1 specifies general requirements for Zhaga compliant components of LED Luminaires.

IEC 62868-2-1:2020 specifies safety requirements for semi-integrated organic light emitting diode modules operating with an external controlgear connected to the mains voltage, and which, in addition, have a control means inside ("semi-integrated") for operation under constant voltage, constant current or constant power and have a rated voltage up to 120 V ripple free DC or 50 V AC RMS at 50 Hz or 60 Hz.

IEC 62868-2-2:2020 specifies the safety requirements for integrated organic light-emitting diode (OLED) modules for use on ripple free DC supplies up to 1000 V or AC supplies up to 1 000 V RMS at 50 Hz or 60Hz.

IEC 63103:2020(E) specifies methods of measurement of electrical power consumption in non-active mode(s), as applicable for electrical lighting equipment. This includes electrical lighting equipment incorporating non-illumination components.
This document specifies neither performance requirements nor limits on power consumption.
This document applies to lighting equipment connected to a supply voltage up to 1 500 V DC or up to 1 000 V AC.
This document is intended to be referenced by lightin...view more

This document specifies performance requirements for electronic controlgear for use on DC or
AC supplies up to 1 000 V (alternating current at 50 Hz or 60 Hz) and with an output
frequency which can deviate from the supply frequency, associated with LED modules
according to IEC 62031. Controlgear for LED modules specified in this document are
designed to provide constant voltage or current. Deviations from the pure voltage and current
types do not exclude the gear from this document.
NOTE 1...view more

This document describes a method, based on measurements combined with calculations, to
determine specific characteristics of the inrush current of single and/or multiple lighting products
of the same type. Lighting products include the following:
• light sources with integrated controlgear,
• controlgear,
• luminaires.
The inrush current characteristics that are determined are
• the peak inrush current,
• the inrush current pulse duration.
This document applies to lighting products conn...view more

IEC 62868-1:2020 specifies general safety requirements of OLED products for use on DC supplies up to 1000 V or AC supplies up to 1000 V at 50 Hz or 60 Hz for indoors and similar general lighting purposes.
This document applies to any OLED light sources which are not covered by IEC 62868-2 (all parts).
This first edition cancels and replaces IEC 62868 published in 2014.

IEC 62384:2020 is available as IEC 62384:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62384:2020 specifies performance requirements for electronic controlgear for use on DC or AC supplies up to 1 000 V (alternating current at 50 Hz or 60 Hz) and with an output frequency which can deviate from the supply frequency, associated with LED modules according to IEC 62031. Controlgear for L...view more

IEC 63129:2020 describes a method, based on measurements combined with calculations, to determine specific characteristics of the inrush current of single and/or multiple lighting products of the same type. Lighting products include the following:
light sources with integrated controlgear,
controlgear,
luminaires.

EN-IEC 62031 specifies general and safety requirements for light-emitting diode (LED) modules: • non-integrated LED modules (LEDni modules) and semi-integrated LED modules (LEDsi modules) for operation under constant voltage, constant current or constant power; • Integrated LED modules (LEDi modules) for use on DC supplies up to 250 V or AC supplies up to 1 000 V at 50 Hz or 60 Hz. LED modules within the scope of this document can be integral, built-in or independent. This document is not applic...view more

IEC 62386-105:2020 applies to control gear and control devices.
Typically, a bus unit according to IEC 62386 (all parts) contains firmware. There are circumstances where it might be necessary to change the firmware after production or shipping of the product. For example if the bus unit does not operate as intended. In such a case, a firmware update of a bus unit via the interface is beneficial.
This firmware update process is primarily designed to be a bug fix process, not a feature extension...view more

NEW!IEC 62031:2018 is available as IEC 62031:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62031:2018 specifies general and safety requirements for light-emitting diode (LED) modules: - non-integrated LED modules (LEDni modules) and semi-integrated LED modules (LEDsi modules) for operation under constant voltage, constant current or constant power; - Integrated LED modules (LEDi module...view more

EN-IEC 63013 is applicable to LED packages for general lighting services. It specifies procedures and conditions for measuring the luminous flux maintenance of LED packages. It also provides the procedures and conditions (criteria) of projecting the long-term luminous flux maintenance based on limited luminous flux maintenance test data collected. Within the context of this document, wherever luminous flux measurement data is specified, radiant flux measurement data can also be used. These proje...view more

IEC 63013:2017 is applicable to LED packages for general lighting services. It specifies procedures and conditions for measuring the luminous flux maintenance of LED packages. It also provides the procedures and conditions (criteria) of projecting the long-term luminous flux maintenance based on limited luminous flux maintenance test data collected. Within the context of this document, wherever luminous flux measurement data is specified, radiant flux measurement data can also be used.

This European Standard specifies the requirements for measurement of electrical, photometric, and colorimetric quantities of LED lamps, modules, light engines and luminaires, for operation with AC or DC supply voltages, possibly with associated control gear. Photometric and colorimetric quantities covered in this standard include total luminous flux, luminous efficacy, partial luminous flux, luminous intensity distribution, centre-beam intensities, luminance and luminance distribution, chromatic...view more

NEXT Action: CCMC to make available
2019-03-06 - Sent to BT for approval of A nnex ZA/ZZ (approved=D162/C075)
2018-12-13 PeC: "Compliant" for LVD
2018-11-20 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved D161/C072)
2018-11-12 PeC: submitted for HAS assessment
2017-11-21 - Negative assessment is received during CDV stage. Consultant assessment request is missing for FDIS.

IEC 62386-104:2019 The IEC 62386 series specifies a bus system for control by digital signals of electronic lighting equipment. This part of IEC 62386 applies to a system with wireless or alternative wired communication between its units, instead of a wired bus system, where the meaning of “wireless or alternative wired communication”, or in short “telecommunication”, is any type of communication network different from the wired system described in IEC 62386-101. Where the electronic lighting eq...view more

IEC 63128:2019 specifies the analogue control interface of controlgear which has the function of controlling the output of the controlgear. The output of the controlgear is controlled between minimum/off and maximum values by the voltage control device sinking the controlgear current source. This document does not specify safety requirements for the analogue interface of controlgear. Safety requirements are given in IEC 61347 (all parts).

IEC TR 63037:2019 is available as IEC TR 63037:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TR 63037:2019 provides guidance to controlgear/integrated lamp designers for the development of products suitable to operate with future phase-cut dimmers. It describes the possible voltage signals and the expected response of the controlgear/integrated lamps. This document describes the expec...view more

IEC 63146:2019 establishes requirements for specification sheets relating to light emitting diode (LED) packages designed for the emission of white light for general lighting applications. This document does not contain compliance criteria.

NEXT Action: CCMC to make available
2019-01-21 PeC: "Compliant" for LVD, sent to BT for integration (approved=D162/C043)
2018-11-21 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved=D161/C073)
2018-11-12 PeC: submitted for HAS assessment
2017-07-31 - Cannot allocate for publication due to negative assessment from Consultant.

This European Standard specifies the requirements for measurement of electrical, photometric, and colorimetric quantities of LED lamps, modules, light engines and luminaires, for operation with AC or DC supply voltages, possibly with associated control gear. Photometric and colorimetric quantities covered in this standard include total luminous flux, luminous efficacy, partial luminous flux, luminous intensity distribution, centre-beam intensities, luminance and luminance distribution, chromatic...view more

This document defines selection ranks for LED Luminaires, and LEDs including OLEDs for the use in aircraft lighting. The size of these ranks is defined by the use of grades. This European Standard is valid for photopic light levels only.

NEXT Action: CCMC to make available
2019-03-06 - Sent to BT for approval of A nnex ZA/ZZ (approved=D162/C075)
2018-12-13 PeC: "Compliant" for LVD
2018-11-20 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved D161/C072)
2018-11-12 PeC: submitted for HAS assessment
2017-11-21 - Negative assessment is received during CDV stage. Consultant assessment request is missing for FDIS.

NEXT Action: CCMC to make available
2019-01-21 PeC: "Compliant" for LVD, sent to BT for integration (approved=D162/C043)
2018-11-21 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved=D161/C073)
2018-11-12 PeC: submitted for HAS assessment
2017-07-31 - Cannot allocate for publication due to negative assessment from Consultant.

IEC 62386-104:2019 The IEC 62386 series specifies a bus system for control by digital signals of electronic lighting equipment. This part of IEC 62386 applies to a system with wireless or alternative wired communication between its units, instead of a wired bus system, where the meaning of “wireless or alternative wired communication”, or in short “telecommunication”, is any type of communication network different from the wired system described in IEC 62386-101.
Where the electronic lighting e...view more

IEC 63128:2019 specifies the analogue control interface of controlgear which has the function of controlling the output of the controlgear. The output of the controlgear is controlled between minimum/off and maximum values by the voltage control device sinking the controlgear current source.
This document does not specify safety requirements for the analogue interface of controlgear. Safety requirements are given in IEC 61347 (all parts).

IEC 63146:2019 establishes requirements for specification sheets relating to light emitting diode (LED) packages designed for the emission of white light for general lighting applications. This document does not contain compliance criteria.

2019-10-24 PeC: to revisit after SLR is published

IEC 62386-220:2019 specifies a bus system for control by digital signals of electronic lighting equipment which is in line with the requirements of IEC 61347 (all parts), with the addition of DC supplies. This document is applicable to control gear supporting centrally supplied emergency operation as described in EN 50171. This document does not apply to self-contained emergency lighting control gear. These types of control gear are specified in IEC 62386-202.

IEC 62386-220:2019 specifies a bus system for control by digital signals of electronic lighting equipment which is in line with the requirements of IEC 61347 (all parts), with the addition of DC supplies.
This document is applicable to control gear supporting centrally supplied emergency operation as described in EN 50171.
This document does not apply to self-contained emergency lighting control gear. These types of control gear are specified in IEC 62386-202.

CCMC - superseding notice missing

CCMC - superseding notice missing

Addition of Common Modifications and Annex ZZ for the ERP

This part of IEC 62442 defines a measurement and calculation method of the total input
power for controlgear-lamp circuits when operating with their associated fluorescent lamp(s).
The calculation method for the efficiency of the lamp controlgear is also defined. This
document applies to electrical controlgear-lamp circuits consisting only of the controlgear and
the lamp(s). It is intended for use on DC supplies up to 1 000 V and/or AC supplies up to
1 000 V at 50 Hz or 60 Hz.
NOTE Require...view more

This publication also bears the number QC 480301XX0005 which is the specification number in the IEC Quality Assessment System for Electronic Components (IECQ).

NEW!IEC 62442-1:2018 is available as IEC 62442-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-1:2018 defines a measurement and calculation method of the total input power for controlgear-lamp circuits when operating with their associated fluorescent lamp(s). The calculation method for the efficiency of the lamp controlgear is also defined. This document applies to electrical con...view more

IEC 62386-221:2018 specifies the methodology of demand response which focuses on the curtailment of electric loads during peak demand times thus avoiding the requirement to find new sources of generation capacity. By using load shedding, the lighting system responds to the demands of the energy supply. This document is applicable to control gear supporting the demand response functionality.

Addition of Common Modifications and Annex ZZ for the ERP