Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document describes the methods for testing electrical characteristics of electric
double-layer capacitor cells (hereinafter referred to as "capacitor") used for peak power
assistance in hybrid electric vehicles.
All the tests in this document are type tests.
This document can also be applicable to the capacitor used in idling reduction systems (start
and-stop systems) for the vehicles.
This document can also be applicable to the capacitor modules consisting of more than one
cell.
NOTE Annex E provides information on endurance cycling test.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC corrigendum

  • Corrigendum
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specifications. This standard applies to grading capacitors falling into one or both of the following categories for: - mounting on air-insulated circuit-breakers; - mounting on enclosed circuit-breakers (for example immersed in SF6, in oil, etc.). The testing for each of the above applications is in some cases different. The object of this standard is: - to define uniform rules regarding performances, testing and rating; - to define specific safety rules; - to provide a guidance for installation and operation. Keywords: grading capacitors, circuit-breakers

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. NOTE These lamps and associated ballasts are covered by IEC 60081, IEC 60901, IEC 60188, IEC 60192, IEC 60662, and IEC 61167 and by IEC 61347-2-8 and IEC 61347-2-9, respectively. It covers capacitors intended for connection in shunt or in series with the lamp circuit or an effective combination of these. It covers only impregnated or unimpregnated capacitors, having a dielectric of paper, plastic film or a combination of both, either metallized or with metal foil electrodes. This standard does not cover radio-interference suppressor capacitors the requirements for which are found in IEC 60384-14. Tests given in this standard are type tests. Requirements for testing individual capacitors during production are not included.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60063:2015 provides series of preferred values for the resistance of resistors and for the capacitance of capacitors. The definition of such series with a defined numeric resolution is a basic prerequisite for the marking and coding of capacitors and resistors with their respective capacitance or resistance values as described in IEC 60062. This edition includes the following significant technical changes with respect to the previous edition:
- revision of the information on a relationship between an E Series and the tolerance of a resistance or capacitance value of a respective component;
- introduction of advice on a possible deduction from the marking of a component to an associated E Series and also to an associated tolerance;
- complete editorial revision.

  • Standard
    20 pages
    English and French language
    sale 15% off

IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specifications. This standard applies to grading capacitors falling into one or both of the following categories for:
- mounting on air-insulated circuit-breakers;
- mounting on enclosed circuit-breakers (for example immersed in SF6, in oil, etc.). The testing for each of the above applications is in some cases different. The object of this standard is:
- to define uniform rules regarding performances, testing and rating;
- to define specific safety rules;
- to provide a guidance for installation and operation. Keywords: grading capacitors, circuit-breakers

  • Standard
    71 pages
    English and French language
    sale 15% off

This part of IEC 60127 covers requirements for miniature fuse-links for special applications. It does not apply to fuses completely covered by the subsequent parts of IEC 60269-1. It does not apply to miniature fuse-links for appliances intended to be used under special conditions, such as in corrosive or explosive atmospheres. This standard applies in addition to the requirements of IEC 60127-1. This standard is applicable to fuse-links with a rated voltage not exceeding 1000 V, a rated current not exceeding 20 A and a rated breaking capacity not exceeding 50 kA. Miniature fuse-links for special applications are not intended to be replaced by the end-user of an electrical / electronic appliance. The object of this standard is to establish uniform test methods for miniature fuse-links for special applications, so as to allow verification of the values (for example melting time and breaking capacity values) specified by the manufacturer.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following:
- employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions from Table 1 to the informative Annex A,
- addition of two smaller diameters of wire terminations in Table 1, and
- tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.

  • Standard
    12 pages
    English and French language
    sale 15% off

IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with respect to the first edition are the following:
- employment of the millimetre-based grid, the preferred grid system given in IEC 60097,
- employment of SI units only, causing deletion of the imperial dimensions from Table 1,
- reduction of the tolerance on the chamfer depth in Figure 1, and
- introduction of requirements on information to be given in a relevant specification.

  • Standard
    20 pages
    English and French language
    sale 15% off

IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 62490 provides the equivalent series inductance L (ESL) measuring method
for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 Nh to 10 nH.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.

  • Standard
    21 pages
    English and French language
    sale 15% off

IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.

  • Standard
    29 pages
    English and French language
    sale 15% off

IEC 60915:2006 contains preferred dimensions for shaft ends and bushes and for the mounting of single-hole, bush-mounted, shaft-operated variable capacitors, variable resistors and potentiometers. If other dimensions not listed in this standard have to be used, it is recommended to select them also from IEC 60390 and IEC 60620. This second edition cancels and replaces the first edition published in 1987 and constitutes a minor revision, related to tables, figures and references. This bilingual version, published in 2008-07, corresponds to the English version. The contents of the corrigendum of December 2008 have been included in this copy.

  • Standard
    31 pages
    English and French language
    sale 15% off

This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. NOTE These lamps and associated ballasts are covered by IEC 60081, IEC 60901, IEC 60188, IEC 60192, IEC 60662, and IEC 61167 and by IEC 61347-2-8 and IEC 61347-2-9, respectively. It covers capacitors intended for connection in shunt or in series with the lamp circuit or an effective combination of these. It covers only impregnated or unimpregnated capacitors, having a dielectric of paper, plastic film or a combination of both, either metallized or with metal foil electrodes. This standard does not cover radio-interference suppressor capacitors the requirements for which are found in IEC 60384-14. Tests given in this standard are type tests. Requirements for testing individual capacitors during production are not included.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies the requirements for both self-healing and non-self- healing continuously rated a.c. capacitors of up to and including 2,5 kvar, and not less than 0,1 F, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. Does not cover radio-interference suppressor capacitors, the requirements for which are given in IEC 60384-14.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

It has the status of a horizontal standard in accordance with IEC Guide 108.

  • Standard
    15 pages
    English, French and Russian language
    sale 15% off
  • Standard
    33 pages
    English, French and Russian language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    18 pages
    Slovenian, English, German and French language
    sale 10% off
    e-Library read for
    1 day

It has the status of a horizontal standard in accordance with IEC Guide 108.

  • Standard – translation
    26 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day

This standard describes the methods for testing electrical characteristics of electric doublelayer capacitor cells (hereinafter referred to as capacitor) to be used for peak power assistance in hybrid electric vehicles.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Presents preferred diameters in tabular form in the metric and inch-pound unit sizes.

  • Standardization document
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kvar, and not less than 0,1 F, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. Does not cover radio-interference suppressor capacitors the requirements for which are given in IEC 60384-14.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN following parallel vote * Corrigendum to EN/A1 issued December 1998

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Superseded by EN 60062:2005

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Superseded by EN 60062:2005

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies a colour code of 12 colours for values and tolerances of fixed resistors and a letter and digit code for resistance and capacitance values and tolerances.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day