This document applies to voltage class B electric propulsion systems and connected auxiliary electric systems of electrically propelled road vehicles. It applies to electric circuits and components in these systems. This document focuses on the characteristics at the DC voltage class B terminals of these components as specified in ISO 21498-1. It describes testing methods, test conditions and test requirements for components exposed to electrical behaviour caused by operation of electric loads a...view more

    • sale 15% off
    • Standard
      48 pages
      English language
    • sale 15% off
    • Draft
      48 pages
      English language

This document applies to the DC EV supply equipment for charging electric road vehicles with
a rated supply voltage of up to 480 V AC or up to 600 V DC, with rated output voltage not
exceeding 120 V DC and output currents not exceeding 100 A DC.
This document provides the requirements for the DC EV supply equipment where the secondary
circuit is protected from the primary circuit by electrical separation.
Requirements for bi-directional power flow are not covered in this document.
This doc...
view more

    • sale 10% off
    • Standard
      69 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61980 applies to the supply device for charging electric road vehicles using
wireless methods at standard supply voltages per IEC 60038 up to 1 000 V AC and up to
1 500 V DC.
Electric road vehicles (EV) covers road vehicles, including plug-in hybrid road vehicles (PHEV)
that derive all or part of their energy from on-board rechargeable energy storage systems
(RESS).
This document also applies to wireless power transfer (WPT) equipment supplied from on-site
storage systems...
view more

    • sale 10% off
    • Standard
      48 pages
      English language
    • e-Library read for
      1 day

This document applies to voltage class B electric propulsion systems and connected auxiliary electric systems of electrically propelled road vehicles. Additionally, it applies to electric circuits and components in these systems. This document provides specifications of voltage sub-classes related to DC electric circuits. It also provides specifications of characteristics which are relevant for design and operation of systems and components for the voltage sub-classes. This document does not cov...view more

    • sale 15% off
    • Standard
      12 pages
      English language
    • sale 15% off
    • Draft
      12 pages
      English language

IEC 61851-25:2020 applies to the DC EV supply equipment for charging electric road vehicles with a rated supply voltage of up to 480 V AC or up to 600 V DC, with rated output voltage not exceeding 120 V DC and output currents not exceeding 100 A DC.
This document provides the requirements for the DC EV supply equipment where the secondary circuit is protected from the primary circuit by electrical separation.
Requirements for bi-directional power flow are not covered in this document.
This do...
view more

    • sale 15% off
    • Standard
      135 pages
      English and French language

IEC 61980-1:2020 applies to the supply device for charging electric road vehicles using wireless methods at standard supply voltages per IEC 60038 up to 1 000 V AC and up to 1 500 V DC.
Electric road vehicles (EV) covers road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from on-board rechargeable energy storage systems (RESS).
This document also applies to wireless power transfer (WPT) equipment supplied from on-site storage systems (e.g. buff...
view more

    • sale 15% off
    • Standard
      88 pages
      English and French language

This draft European Standard applies to personal light electric vehicles totally or partially electrically powered from self-contained power sources with or without self-balancing system.
This draft European Standard applies to vehicles having battery voltages up to 100VDC, and/or an integrated battery charger with up to a 240VAC input.
It specifies safety requirements, test methods, marking and information relating to personal light electric vehicles to reduce the risk of injuries to both thi...
view more

    • sale 10% off
    • Standard
      86 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      85 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      90 pages
      English language
    • e-Library read for
      1 day

This document specifies the requirements of the physical and data link layer of a wireless High Level
Communication (HLC) between Electric Vehicles (EV) and the Electric Vehicle Supply Equipment
(EVSE). The wireless communication technology is used as an alternative to the wired communication
technology as defined in ISO 15118-3.
It covers the overall information exchange between all actors involved in the electrical energy exchange.
ISO 15118 (all parts) are applicable for conductive charg...
view more

    • sale 10% off
    • Standard
      41 pages
      English language
    • e-Library read for
      1 day

EN-IEC 55036 defines limits for 3 m measurement distance and methods of measurement thatare designed to provide protection for off-board receivers (at 10 m distance) in the frequencyrange of 150 kHz to 30 MHz when used in the residential environment.This document applies to the emission of electromagnetic energy which might causeinterference to radio reception and which is emitted from electric and hybrid electric vehiclespropelled by an internal traction battery (see 3.2 and 3.3) when operated ...view more

    • sale 10% off
    • Standard
      27 pages
      English language
    • e-Library read for
      1 day

2020-01-09: TC 23E requests BT to decouple the EN from the EMC Directive and publish the standard without delay -  to offer for LVD: partial compliance but all remarks have been implemented.
2019-10-01: CLC/TC 23E and CLC/TC 210 to coordinate to address the statistical methods.

    • sale 10% off
    • Amendment
      23 pages
      English language
    • e-Library read for
      1 day

This document specifies the requirements of the physical and data link layer of a wireless High Level Communication (HLC) between Electric Vehicles (EV) and the Electric Vehicle Supply Equipment (EVSE). The wireless communication technology is used as an alternative to the wired communication technology as defined in ISO 15118‑3. It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) are applicable for conductive charging a...view more

    • sale 15% off
    • Standard
      33 pages
      English language
    • sale 15% off
    • Standard
      35 pages
      French language
    • sale 15% off
    • Draft
      33 pages
      English language

This document specifies the requirements of the physical and data link layer of a wireless High Level Communication (HLC) between Electric Vehicles (EV) and the Electric Vehicle Supply Equipment (EVSE). The wireless communication technology is used as an alternative to the wired communication technology as defined in ISO 15118‑3.
It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) are applicable for conductive charging ...
view more

    • sale 15% off
    • Standard
      33 pages
      English language

This Part of IEC 61980, (in a first step as Technical Specification for three-year period) applies to communication between electric road vehicle (EV) and wireless power transfer (WPT) systems when connected to the supply network, at standard supply voltages per IEC 60038 up to 1000V a.c. and up to 1500 V d.c..This standard also applies to Wireless Power Transfer (WPT) equipment supplied from on-site storage systems (e.g. buffer batteries etc.) at standard supply voltages per IEC 60038 up to 100...view more

    • sale 10% off
    • Technical specification
      87 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61980 series, (in a first step as Technical Specification for three-year period) applies to the equipment for the magnetic field-wireless power transfer (MF-WPT) of electric power from the supply network to electric road vehicles for purposes of supplying electric energy to the RESS (Rechargeable energy storage system) and/or other on-board electrical systems in an operational state when connected to the supply network, at standard supply voltages ratings per IEC 60038 up to 100...view more

    • sale 10% off
    • Technical specification
      111 pages
      English language
    • e-Library read for
      1 day

IEC 62893-4-1:2020 applies to cables for DC charging according to mode 4 of IEC 61851-1. These cables are not intended to be used with a thermal management system such as that specified in IEC 61851-23.
Charging cables specified in IEC 62893 (all parts) are intended to be used for electrical appliances of class II equipment.
The maximum conductor operating temperature for the cables in this document is 90 °C.
The test methods specified are given in IEC 62893-2, IEC 60245-2, IEC 60332-1-2, IEC...
view more

    • sale 15% off
    • Standard
      18 pages
      English language

This document specifies electric safety requirements for conductive connection of electrically propelled
road vehicles to external electric circuits. External electric circuits include external electric power
supplies and external electric loads. This document provides requirements for the charging modes
2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document provides
requirements regarding the connection to an isolated DC EV charging station according to IE...
view more

    • sale 10% off
    • Standard
      49 pages
      English language
    • e-Library read for
      1 day

This document defines the requirements and operation of the on-board vehicle equipment that enables magnetic field wireless power transfer (MF-WPT) for traction battery charging of electric vehicles. It is intended to be used for passenger cars and light duty vehicles. This document addresses the following aspects for an EV device: — safety requirements; — transferred power and power transfer efficiency; — ground clearance of the EV device; — functionality with associated off-board systems under...view more

    • sale 15% off
    • Standard
      39 pages
      English language
    • sale 15% off
    • Standard
      41 pages
      French language

IEC TS 62196-3-1:2020(E) applies to accessories and cable assemblies with the same configuration as specified in IEC 62196-3:2014 with rated operating voltage not exceeding 1 500 V DC and a rated current not exceeding 500 A that employ
- thermal sensing, or
- thermal transport and thermal sensing with the system architecture described in 4.101.
These accessories and cable assemblies are intended to be used in conductive charging systems for circuits specified in IEC 61851-23.
NOTE Edition 2 ...
view more

    • sale 15% off
    • Technical specification
      62 pages
      English language

This document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits. External electric circuits include external electric power supplies and external electric loads. This document provides requirements for the charging modes 2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document provides requirements regarding the connection to an isolated DC EV charging station according to IEC 61...view more

    • sale 10% off
    • Standard
      49 pages
      English language
    • e-Library read for
      1 day

This document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits. External electric circuits include external electric power supplies and external electric loads. This document provides requirements for the charging modes 2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document provides requirements regarding the connection to an isolated DC EV charging station according to IEC 61...view more

    • sale 15% off
    • Standard
      41 pages
      English language
    • sale 15% off
    • Standard
      43 pages
      French language

This European Standard establishes a basis for the other parts of IEC 63119, specifying the terms and definitions, general description of the system model, classification, information exchange and security mechanisms for roaming between EV charge service providers (CSPs), charging station operators (CSOs) and clearing house platforms through roaming endpoints. It provides an overview and describes the general requirements of the EV roaming service system. IEC 63119 (all parts) is applicable to h...view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies performance tests for the motor and the inverter designed as a voltage class B electric propulsion system for electrically propelled road vehicles.

    • sale 15% off
    • Standard
      25 pages
      English language

This document specifies the performance tests for the motor system designed as a voltage class B electric propulsion system for electrically propelled road vehicles.

    • sale 15% off
    • Standard
      12 pages
      English language

This document specifies operating load tests and test criteria for motor and inverter designed as a voltage class B electric propulsion system for electrically propelled road vehicles.

    • sale 15% off
    • Standard
      22 pages
      English language

This document specifies a chassis dynamometer test procedure to measure the exhaust emissions and the electric energy and fuel consumption for the vehicles. This document applies to vehicles with the following characteristics: — vehicles classified as passenger cars or light duty trucks, as defined in the relevant regional applicable driving test (ADT) standard; — the nominal energy of the rechargeable energy storage system (RESS) is at least 2 % of the total energy consumption over an ADT; — in...view more

    • sale 15% off
    • Standard
      23 pages
      English language

This document specifies the test procedures for performance and operating load for voltage class B electric propulsion components (motor, inverter, DC/DC converter) and their combinations (motor system) of electrically propelled road vehicles. This document specifies the terms and definitions used in the ISO 21782 series and general test conditions.

    • sale 15% off
    • Standard
      14 pages
      English language

IEC 63119-1:2019 establishes a basis for the other parts of IEC 63119, specifying the terms and definitions, general description of the system model, classification, information exchange and security mechanisms for roaming between EV charge service providers (CSP), charging station operators (CSOs) and clearing house platforms through roaming endpoints. It provides an overview and describes the general requirements of the EV roaming service system. IEC 63119 (all parts) is applicable to high-lev...view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61851 applies to EV supply equipment for charging electric road vehicles, with a rated supply voltage up to 1 000 V AC or up to 1 500 V DC. and a rated output voltage up to 1 000 V AC. or up to 1 500 V DC.
Electric road vehicles (EV) cover all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from on-board rechargeable energy storage systems (RESS).
This standard also applies to EV supply equipment supplied from on-site stora...
view more

    • sale 10% off
    • Standard
      149 pages
      English language
    • e-Library read for
      1 day

IEC 61851-1:2017 applies to EV supply equipment for charging electric road vehicles, with a rated supply voltage up to 1 000 V AC or up to 1 500 V DC and a rated output voltage up to 1 000 V AC or up to 1 500 V DC. Electric road vehicles (EV) cover all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from on-board rechargeable energy storage systems (RESS). The aspects covered in this standard include: -  the characteristics and operating cond...view more

    • sale 10% off
    • Standard
      149 pages
      English language
    • e-Library read for
      1 day

IEC 63119-1:2019 establishes a basis for the other parts of IEC 63119, specifying the terms and definitions, general description of the system model, classification, information exchange and security mechanisms for roaming between EV charge service providers (CSP), charging station operators (CSOs) and clearing house platforms through roaming endpoints. It provides an overview and describes the general requirements of the EV roaming service system.
IEC 63119 (all parts) is applicable to high-le...
view more

    • sale 15% off
    • Standard
      28 pages
      English and French language

IEC TS 61980-2:2019 applies to communication between electric road vehicle (EV) and wireless power transfer (WPT) systems when connected to the supply network, at standard supply voltages per IEC 60038 up to 1000 V AC and up to 1500 V DC.
This document also applies to wireless power transfer equipment supplied from on-site storage systems (e.g. buffer batteries) at standard supply voltages per IEC 60038 up to 1000 V AC and up to 1500 V DC.
The aspects covered in this document include
– standa...
view more

    • sale 15% off
    • Technical specification
      84 pages
      English language

IEC TS 61980-3:2019 applies to the equipment for the magnetic field wireless power transfer (MF-WPT) of electric power from the supply network to electric road vehicles for purposes of supplying electric energy to the RESS (rechargeable energy storage system) and/or other on-board electrical systems. The MF-WPT system operates at standard supply voltages ratings per IEC 60038 up to 1 000 V AC and up to 1 500 V DC The power transfer takes place while the electric vehicle (EV) is stationary.
This...
view more

    • sale 15% off
    • Technical specification
      107 pages
      English language

to clarify and correct the wording of EN 50620 and to amend Annex ZZ, following the request of the NAC

    • sale 10% off
    • Amendment
      10 pages
      English language
    • e-Library read for
      1 day

This document, as a basis for the other parts of the ISO 15118 series, specifies terms and definitions, general requirements and use cases for conductive and wireless HLC between the EVCC and the SECC.
This document is applicable to HLC involved in conductive and wireless power transfer technologies in the context of manual or automatic connection devices.
This document is also applicable to energy transfer either from EV supply equipment to charge the EV battery or from EV battery to EV suppl...
view more

    • sale 10% off
    • Standard
      126 pages
      English language
    • e-Library read for
      1 day

This document specifies safety requirements for rechargeable energy storage systems (RESS) of electrically propelled road vehicles for the protection of persons. It does not provide the comprehensive safety information for the manufacturing, maintenance and repair personnel. NOTE 1 Requirements for motorcycles and mopeds are specified in ISO 13063 and ISO 18243. NOTE 2 Additional safety requirements can apply for RESS that can be recharged by means different from supplying electric energy (e.g. ...view more

    • sale 15% off
    • Standard
      26 pages
      English language

This part of IEC 62660 specifies performance and life testing of secondary lithium-ion cells
used for propulsion of electric vehicles including battery electric vehicles (BEV) and hybrid
electric vehicles (HEV).
NOTE 1 Secondary lithium-ion cell used for propulsion of plug-in hybrid electric vehicle (PHEV) can be tested by
the procedure either for BEV application or HEV application, according to the battery system design, based on the
agreement between the cell manufacturer and the customer...
view more

    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day

This part of IEC 62660 specifies test procedures to observe the reliability and abuse
behaviour of secondary lithium-ion cells and cell blocks used for propulsion of electric
vehicles including battery electric vehicles (BEV) and hybrid electric vehicles (HEV).
NOTE 1 Secondary lithium-ion cells used for propulsion of plug-in hybrid electric vehicles (PHEV) can be tested
by the procedure either for BEV application or HEV application, according to the battery system design, based on
the agre...
view more

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day

ISO 15118-1:2019 This document, as a basis for the other parts of the ISO 15118 series, specifies terms and definitions, general requirements and use cases for conductive and wireless HLC between the EVCC and the SECC.
This document is applicable to HLC involved in conductive and wireless power transfer technologies in the context of manual or automatic connection devices.
This document is also applicable to energy transfer either from EV supply equipment to charge the EV battery or from EV ba...
view more

    • sale 15% off
    • Standard
      117 pages
      English language

This European Standard lays down harmonized identifiers for power supply for electric road vehicles. The requirements in this standard are to complement the informational needs of users regarding the compatibility between the charging stations, the cable assemblies and the vehicles that are placed on the market. The identifier is intended to be visualized at charging stations, on vehicles, on cable assemblies, in EV dealerships and in consumer manuals as described in this document.
Power supply...
view more

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day

This document, as a basis for the other parts of the ISO 15118 series, specifies terms and definitions, general requirements and use cases for conductive and wireless HLC between the EVCC and the SECC. This document is applicable to HLC involved in conductive and wireless power transfer technologies in the context of manual or automatic connection devices. This document is also applicable to energy transfer either from EV supply equipment to charge the EV battery or from EV battery to EV supply ...view more

    • sale 15% off
    • Standard
      117 pages
      English language
    • sale 15% off
    • Standard
      131 pages
      French language

This document establishes a vocabulary of terms and the related definitions used in ISO/TC 22/SC 37 standards.

    • sale 15% off
    • Technical report
      38 pages
      English language

This document lays down harmonized identifiers for power supply for electric road vehicles. The requirements in this standard are to complement the informational needs of users regarding the compatibility between the EV charging stations, the cable assemblies and the vehicles that are placed on the market. The identifier is intended to be visualized at EV charging stations, on vehicles, on cable assemblies, in EV dealerships and in consumer manuals as described in this document.
Power supply fo...
view more

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day

This part of IEC 62840 provides the safety requirements for a battery swap system, for the
purposes of swapping swappable battery system (SBS) of electric vehicles. The battery swap
system is intended to be connected to the supply network. The power supply is up to 1 000 V
AC or up to 1 500 V d.c, in accordance with IEC 60038.
This standard also applies to battery swap systems supplied from on-site storage systems
(e.g. buffer batteries).
Aspects covered in this standard:
• safety require...
view more

    • sale 10% off
    • Standard
      32 pages
      English language
    • e-Library read for
      1 day

This part of IEC 62660 specifies test procedures to observe the reliability and abuse behaviour of secondary lithium-ion cells and cell blocks used for propulsion of electric vehicles including battery electric vehicles (BEV) and hybrid electric vehicles (HEV). NOTE 1 Secondary lithium-ion cells used for propulsion of plug-in hybrid electric vehicles (PHEV) can be tested by the procedure either for BEV application or HEV application, according to the battery system design, based on the agreement...view more

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day

IEC 62660-1:2018 is available as IEC 62660-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62660-1:2018 specifies performance and life testing of secondary lithium-ion cells used for propulsion of electric vehicles including battery electric vehicles (BEV) and hybrid electric vehicles (HEV). This document specifies the test procedures to obtain the essential characteristics of lithium-...view more

    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      42 pages
      English language
    • e-Library read for
      1 day

ISO 15118-5:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an Electric Vehicle or Supply Equipment Communication Controller (EVCC or SECC) with support for PLC-based High Level Communication (HLC) and Basic Signaling according to ISO 15118‑3. These conformance tests specify the testing of capabilities and behaviors of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118‑3 ...view more

    • sale 10% off
    • Standard
      414 pages
      English language
    • e-Library read for
      1 day

ISO 15118-4:2018 specifies conformance tests in the form of an Abstract Test Suite (ATS) for a System Under Test (SUT) implementing an EVCC or SECC according to ISO 15118-2. These conformance tests specify the testing of capabilities and behaviors of an SUT as well as checking what is observed against the conformance requirements specified in ISO 15118-2 and against what the supplier states the SUT implementation's capabilities are.
The capability tests within the ATS check that the observable ...
view more

    • sale 10% off
    • Standard
      1470 pages
      English language
    • e-Library read for
      1 day