75 - PETROLEUM AND RELATED TECHNOLOGIES

This International Standard specifies two methods for the determination of the biomass content in solid
recovered fuels: the selective dissolution and the 14C content method. The standard provides the
criteria for choosing the more appropriate method and some examples of application.

This document specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 2,5 MPa (25 bar) within the temperature range −30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C.

This European Standard specifies a method for the determination of the boiling range distribution of petroleum products by capillary gas chromatography using flame ionisation detection. The standard is applicable to materials having a vapour pressure low enough to permit sampling at ambient temperature and a boiling range of at least 100 °C. The standard is applicable to distillates with initial boiling points (IBP) above 100 °C and final boiling points (FBP) below 750 °C, for example, middle di...view more

This International Standard defines terms and definitions concerned in all standardisation work within
the scope of ISO/TC 300, i.e. terms used in the field of production and trade of solid recovered fuels
that are prepared from non-hazardous waste.
NOTE Solid biofuels are covered by the scope of ISO/TC 238.
Definitions in other standards with a scope different from the scope of this International Standard can
be different from the definitions in this International Standard.

This European Standard specifies a method for the determination of the boiling range distribution of petroleum products by capillary gas chromatography using flame ionisation detection. The standard is applicable to materials having a vapour pressure low enough to permit sampling at ambient temperature, and which have a boiling range of at least 100 °C. The standard is applicable to materials with initial boiling points (IBP) above 100 °C and final boiling points (FBP) above 750 °C, for example,...view more

This European Standard describes a method for the determination of the boiling range distribution of petroleum products by capillary gas chromatography using flame ionisation detection. The standard is applicable to crude oils. The boiling range distribution and recovery to C100 or C120 can be determined.
Two procedures are described: single and dual analysis mode. The basis of each is the calculation procedure as described in Annex A.
NOTE 1   This standard does not purport to address all of th...view more

This document specifies procedures and requirements for the transfer of bunkers to vessels by bunker tankers using the Coriolis mass flow meter (MFM) system. It encompasses the process leading to the approval of the MFM system as installed on bunker tankers and post-approval bunkering operation. It covers terminology, specifications, requirements and procedures on metrology, system integrity, metering system selection and installation, MFM system verification, bunker delivery and dispute handlin...view more

This International Standard specifies a method for the determination of carbon (C), hydrogen (H),
nitrogen (N) and sulphur (S) by instrumental method. Depending on the amount of test portion used,
micro and macro instrumental apparatus are used.
An alternative method based on high temperature furnace combustion and IR detection is described in
Annex A.

This document describes the investigation into diesel vehicle common rail fuel injection system damage
and excessive wear problems in a number of countries across Europe since 2014 carried out by
CEN/TC 19/WG 24 Abrasive Particles Task Force.

This document specifies the code to be used in defining the quantity of solid particles in the fluid used in a given hydraulic fluid power system.

This document specifies three methods for the determination of the biomass content in solid recovered fuels: the 14C content method, the selective dissolution and the manual sorting methods.

This document specifies detailed manufacturing requirements for circular steel and nickel alloy
compact flanged connections and associated seal rings, for designated pressures and temperatures
in class designations CL 150 (PN 20) to CL 1500 (PN 260) for nominal sizes from DN 15 (NPS ½) to
DN 1200 (NPS 48), and for CL 2500 (PN 420) for nominal sizes from DN 15 (NPS ½) to DN 600 (NPS 24).
NOTE NPS is expressed in accordance with ASME B36.10M and ASME B36.19M.
This document is applicable to we...view more

This document specifies basket heating tests for the characterization of self-heating properties of solid biofuel pellets. This document includes: a) a compilation of basket heating test methods; b) guidance on the applicability and use of basket heating tests for solid biofuel pellets; c) information on the application of basket heating test data for calculations of critical conditions in storages. Data on spontaneous heat generation determined using this document is only associated with the sp...view more

This document gives requirements and recommendations for the selection and qualification of CRAs
(corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas
production and natural gas treatment plants in H2S-containing environments whose failure can pose
a risk to the health and safety of the public and personnel or to the environment. It can be applied to
help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, ...view more

This document gives requirements and recommendations for the selection and qualification of carbon
and low-alloy steels for service in equipment used in oil and natural gas production and natural gas
treatment plants in H2S-containing environments, whose failure can pose a risk to the health and safety
of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion
damage to the equipment itself. It supplements, but does not replace, the materials requi...view more

This document describes general principles and gives requirements and recommendations for the
selection and qualification of metallic materials for service in equipment used in oil and gas production
and in natural-gas sweetening plants in H2S-containing environments, where the failure of such
equipment can pose a risk to the health and safety of the public and personnel or to the environment.
It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements,...view more

This document specifies requirements and provides recommendations applicable to the following types
of fixed steel offshore structures for the petroleum and natural gas industries:
— caissons, free-standing and braced;
— jackets;
— monotowers;
— towers.
In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups,
other bottom founded structures and other structures related to offshore structures (such as underwater
oil storage tanks, bridges a...view more

This document specifies the requirements and test methods of bamboo charcoal for air-purification applications.

This document specifies the requirements and test methods for bamboo charcoal. It is applicable to the bamboo charcoal briquette.

This document specifies the requirements and test methods of the raw and moulded bamboo charcoal for fuel applications.

This document defines terms for solid recovered fuels to enable the user to understand the scope of the work of ISO/TC 300. Where a term and definition are required in a single standard, the term and definition will be referenced in that standard.

This document establishes a common basis for, and assistance in, the classification of applications and multiphase meters, as well as guidance and recommendations for the implementation and use of such meters. The so-called in-line multiphase flow meters (MPFMs) that directly measure the oil, water and gas flow rates, as well as the partial- and full-separation MPFMs are the main focus of this document. Conventional two- or three-phase separators are not included in this document. Only limited r...view more

This document specifies the determination of total content of carbon, hydrogen, nitrogen and sulfur in solid recovered fuels by instrumental method. Depending on the amount of test portion, micro or macro instrumental apparatus are used. This method is applicable for concentrations on dry matter basis of C > 0,1 %, N > 0,1 %, H > 0,1 % and S > 0,05 %.

This document gives requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the ...view more

This document gives requirements and recommendations for the selection and qualification of carbon and low-alloy steels for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments, whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requireme...view more

This document describes general principles and gives requirements and recommendations for the selection and qualification of metallic materials for service in equipment used in oil and gas production and in natural-gas sweetening plants in H2S-containing environments, where the failure of such equipment can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion damage to the equipment itself. It supplements, but...view more

This document will specify the requirements for LNG for use as a fuel in marine engines. It will define the required values for all relevant parameters and the test method for each of these parameters

This document specifies requirements and provides recommendations applicable to the following types of fixed steel offshore structures for the petroleum and natural gas industries: ? caissons, free-standing and braced; ? jackets; ? monotowers; ? towers. In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups, other bottom founded structures and other structures related to offshore structures (such as underwater oil storage tanks, bridges and conne...view more

This document describes the studies executed to develop a method to analyse the filter blocking tendency after a cold soak step of fatty acid methyl ester (FAME) as a blend component for diesel and of diesel fuel containing up to 30 % (V/V) of fatty acid methyl esters (FAME), respectively.

This document specifies Procedure A, using manual glass viscometers, and Procedure B, using glass
capillary viscometers in an automated assembly, for the determination of the kinematic viscosity, ν,
of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of
liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η,
is obtained by multiplying the measured kinematic viscosity by the density, ρ, of the liquid. Th...view more

This part of ISO 16486 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirement...view more

This European Standard gives general guidelines for the design, material selection, qualification, certification, and testing details for Liquefied Natural Gas (LNG) transfer hoses for offshore transfer or on coastal weather-exposed facilities for aerial, floating and submerged configurations or a combination of these. Whilst this European Standard is applicable to all LNG hoses, it is acknowledged that there may be further specific requirements for floating and submerged hoses.
The transfer ho...view more

This document specifies the quality requirements for Liquefied Natural Gas (LNG) used as a fuel for marine applications. It defines the relevant parameters to measure as well as the required values and the test reference methods for all those parameters. This document applies to LNG from any source, e.g. gas from conventional reservoirs, shale gas, coalbed methane, biomethane, synthetic methane. LNG described in this document can come from synthesis process out of fossil fuels or renewable sourc...view more

This document establishes the principles, specifies the requirements and provides guidance for ice management (IM) in arctic and cold regions, from the point of view of planning, engineering, implementation and documentation. Reference to arctic and cold regions in this document is deemed to include both the Arctic and other regions characterized by low ambient temperatures, sea ice, icebergs and icing conditions. These regions are often remote and lacking in marine and communications infrastruc...view more

This document specifies the minimum technical requirements for surface preparation, materials, application, inspection and testing of internal coating and lining systems that are intended to be applied on internal surfaces of process vessels that are subject to marked pressure/temperature changes and/or potentially corrosive conditions or processes and aggressive chemicals, used in the oil and gas industry.
This document covers both new construction and maintenance works of process vessels as w...view more

This document specifies a method for the determination of the coke bulk density in a large container such as a wagon or skip.

This part of ISO 16486 specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and require...view more

This document specifies the requirements for a heavy-duty series of bolted bonnet steel gate valves for
petroleum refinery and related applications where corrosion, erosion and other service conditions can
indicate a need for full port openings, heavy wall sections and large stem diameters.
This document sets forth the requirements for the following gate valve features:
— bolted bonnet;
— outside screw and yoke;
— rising stems;
— non-rising handwheels;
— single or double gate;
— wedge o...view more

This part of ISO 16486 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing

This document specifies a method for the determination of the gross calorific value of a solid mineral fuel at constant volume and at the reference temperature of 25 °C in a combustion vessel calorimeter calibrated by combustion of certified benzoic acid. The result obtained is the gross calorific value of the analysis sample at constant volume with all the water of the combustion products as liquid water. In practice, fuel is burned at constant (atmospheric) pressure and the water is not conden...view more

This document establishes an extended classification which includes sub-categories of environmentally acceptable lubricants and specifies the minimum requirements for mineral or synthetic based lubricants for the categories CKH, CKJ and CKM, according to ISO 6743-6, and their sub-categories of environmentally acceptable lubricants, intended for the lubrication of open and semi-enclosed gears. This document covers the lubricants applied in the open and semi-enclosed gear systems most currently en...view more

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series of standards is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, this document lays down dimensional charac...view more

This document specifies the requirements for a series of compact steel gate, globe and check valves for
petroleum and natural gas industry applications.
It is applicable to valves of:
— nominal sizes DN 8, 10, 15, 20, 25, 32, 40, 50, 65, 80 and 100,
— corresponding to nominal pipe sizes NPS ¼, ⅜, ½, ¾, 1, 1¼, 1½, 2, 2½, 3 and 4,
— pressure designations PN 16, 25, 40, 63, 100, 250 and 400, and
— pressure designations Class 150, 300, 600, 800, 1 500 and 2 500.
Class 800 is not a listed clas...view more

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, it lays down dimensional characteristics and require...view more

This document specifies Procedure A, using manual glass viscometers, and Procedure B, using glass capillary viscometers in an automated assembly, for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, is obtained by multiplying the measured kinematic viscosity by the density, ρ, of the liquid. The ra...view more

This document describes a method for the determination of the free acidic constituents present in bitumen, conventionally known as acid number.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations...view more

This document provides examples of Declaration of Performance (DoP) and CE Marking for bitumen and bituminous binders for use in the construction and maintenance of roads, airfields and other paved areas.
NOTE 1   Only harmonised technical specifications (product standards or ETAs) cited in the OJEU are the basis for drawing up the Declaration of Performance.
NOTE 2   The product standards this document is related to, are listed in the bibliography.
NOTE 3   The EC database of all harmonized standa...view more

This document describes a method for determination of the salt content in bitumen, conventionally expressed in mg of sodium chloride (noted NaCl as from this point of this document) per kg of bitumen. This method is valid for "equivalent NaCl contents" between 20 mg/kg and 500 mg/kg.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility o...view more