75.200 - Petroleum products and natural gas handling equipment

This part of ISO 16486 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirement...view more

This European Standard gives general guidelines for the design, material selection, qualification, certification, and testing details for Liquefied Natural Gas (LNG) transfer hoses for offshore transfer or on coastal weather-exposed facilities for aerial, floating and submerged configurations or a combination of these. Whilst this European Standard is applicable to all LNG hoses, it is acknowledged that there may be further specific requirements for floating and submerged hoses.
The transfer ho...view more

This part of ISO 16486 specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and require...view more

This part of ISO 16486 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series of standards is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, this document lays down dimensional charac...view more

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. In addition, it lays down dimensional characteristics and require...view more

This document specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing. This document establishes a calculation and d...view more

The objective of ISO 20257-1 is to provide functional guidelines and recommend practices for the design of floating liquefied natural gas (LNG) installations in order to have a safe and environmentally acceptable design and operation of floating LNG installations.
ISO 20257 gives functional guidelines for the design and operation of all floating LNG installations including those for the liquefaction, storage, vaporisation, transfer and handling of LNG.

This document specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore.
This document is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from - 196 °C to + 45 °C.
NOTE   Offshore LNG hose assemblies are also speci...view more

This document provides guidance to support organizations with the implementation of the European standards on CNG and LNG stations for fuelling vehicles (i.e. EN-ISO 16923:2018 and EN-ISO 16924:2018, respectively).
This document cross-references European standards to the international standards listed in EN-ISO 16923:2018 and EN-ISO 16924:2018 and links these standards to relevant European Directives, where applicable.

This part of ISO 20088 describes a method for determining the resistance to cryogenic spray on Cryogenic Spillage Protection (CSP) systems. It is applicable where CSP systems are installed on carbon steel and will be in contact with cryogenic fluids. Liquid jet release is potentially formed at high pressure LNG handling section in LNG liquefaction unit, e.g., around 40 - 60 bar operating pressure. Due to high velocity discharge, it may cause severe condition for cryogenic protection coating by l...view more

This document provides requirements and guidance for the design and operation of floating liquefied natural gas (LNG) installations, including installations for the liquefaction, storage, vaporisation, transfer and handling of LNG, in order to have a safe and environmentally acceptable design and operation of floating LNG installations. This document is applicable to: — floating LNG liquefaction installations (plant) — FLNG; — floating LNG regasification installations (plant) — FSRU; — floating ...view more

This International Standard provides principles and requirements for safe handling and storage of solid biofuels pellets in commercial and industrial applications.
The standard covers the entire handling and storage process of pellets, (i) at a pellets production plant, from the outlet of the cooler unit until loaded for transportation and (ii) at a power plant from the receiving station until fed into a pulverizer or furnace.
The process of production of pellets and safety issues related to pro...view more

CEN/TR 15367-1 provides general guidance on diesel fuel housekeeping to ensure appropriate cleanliness and to prevent onward distribution of contaminants.It does not pre-empt national or local regulations but addresses the issues of contamination by water, sediment, inorganic contaminants, or microbial growth that may occur in the supply chain during manufacture, blending, storage and transportation. It does not address contamination by other fuel products nor does it address possible contaminat...view more

This document describes a method for determining the resistance of Cryogenic Spill Protection (CSP) systems to vapour generated from a cryogenic liquid release where the liquid content is practically zero. It is applicable where CSP systems are installed on carbon steel.
The test provided in this document is not applicable to high pressure cryogenic liquid releases that can be found in refrigeration circuits and in LNG streams immediately post-liquefaction.

This document provides general guidance on diesel fuel housekeeping. It does not pre-empt national or local regulations but addresses the issues of contamination by water, sediment, inorganic contaminants, or microbial growth that may occur in the supply chain during manufacture, blending, storage and transportation. It does not address contamination by other fuel products nor does it address possible contamination by water or sediment that may occur on-board vehicles. An informative note on veh...view more

This document provides guidance to support organizations with the implementation of the European standards on CNG and LNG stations for fuelling vehicles (i.e. EN-ISO 16923:2018 and EN-ISO 16924:2018, respectively).
This document cross-references European standards to the international standards listed in EN-ISO 16923:2018 and EN-ISO 16924:2018 and links these standards to relevant European Directives, where applicable.