77.080 - Ferrous metals

This document specifies an order for listing elements within the chemical composition of steels and most other iron-based alloys, excluding foundry irons. NOTE This document has been developed and is used by ISO/TC 17/SC 4, but can also be used by other ISO/TC 17 subcommittees.

This document specifies a potentiometric titration method for the determination of vanadium in steel
and cast iron.
The method is applicable to vanadium contents between 0,04 % (mass fraction) and 2 % (mass fraction).

This document specifies a potentiometric titration method for the determination of vanadium in steel and cast iron. The method is applicable to vanadium contents between 0,04 % (mass fraction) and 2 % (mass fraction).

This document defines the grades and the corresponding requirements for ausferritic spheroidal graphite cast irons. This document specifies five grades of ausferritic spheroidal graphite cast iron by a classification based on mechanical properties determined on machined test pieces prepared from: — separately cast samples, side-by-side cast or cast-on samples; — samples cut from a casting. This document also specifies two grades by a classification as a function of hardness.

1 Scope This document specifies the properties of unalloyed and low-alloyed grey cast irons used for castings that have been manufactured in sand moulds or in moulds with comparable thermal behaviour. This document specifies the characterizing properties of grey cast irons by any of the following: a) the tensile strength of cast samples; b) if agreed by the manufacturer and the purchaser, the tensile strength of samples cut from a casting; c) if agreed between the manufacturer and the purchaser,...view more

EN-ISO 439 specifies a gravimetric method for the determination of the silicon content in steels and cast irons. The method is applicable to silicon contents between 0,10 % (mass fraction) and 5, 0 % {mass fraction).

EN-ISO 643 specifies a micrographic method of determining apparent ferritic oraustenitic grain size in steels. It describes the methods of revealing grainboundaries and of estimating the mean grain size of specimens with unimodal sizedistribution. Although grains are three-dimensional in shape, the metallographicsectioning plane can cut through a grain at any point from a grain corner, tothe maximum diameter of the grain, thus producing a range of apparent grainsizes on the two-dimensional plane...view more

This document specifies a gravimetric method for the determination of the silicon content in steel and cast iron.
The method is applicable to silicon contents between 0,10 % (mass fraction) and 5,0 % {mass fraction).
NOTE For samples containing molybdenum, niobium, tantalum, titanium, tungsten, zirconium or high levels of chromium, the results are less accurate than for unalloyed matrixes.

This document specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the vanadium content in steel. The method is applicable to vanadium contents between 0,01 % (mass fraction) and 0,80 % (mass fraction), provided that the tungsten content in a 1,0 g test portion is not higher than 1,0 % and/or the titanium content is not higher than 0,5 %.

This document specifies a gravimetric method for the determination of the silicon content in steel and cast iron. The method is applicable to silicon contents between 0,10 % (mass fraction) and 5,0 % {mass fraction). NOTE For samples containing molybdenum, niobium, tantalum, titanium, tungsten, zirconium or high levels of chromium, the results are less accurate than for unalloyed matrixes.

This document specifies a method of classifying the microstructure of graphite in cast irons by
comparative visual analysis.
The purpose of this document is to provide information about the method of graphite classification. It
is not intended to give information on the suitability of cast-iron types and grades for any particular
application.
The particular material grades are specified mainly by mechanical properties and, in the case of
austenitic and abrasion resistant cast irons, by the...view more

This document specifies an order for listing elements within the chemical composition of steels and most other iron-based alloys, excluding foundry irons. NOTE This document has been developed and is used by ISO/TC 17/SC 4, but can also be used by other ISO/TC 17 subcommittees.

This document specifies a method of classifying the microstructure of graphite in cast irons by comparative visual analysis.
The purpose of this document is to provide information about the method of graphite classification. It is not intended to give information on the suitability of cast-iron types and grades for any particular application.
The particular material grades are specified mainly by mechanical properties and, in the case of austenitic and abrasion resistant cast irons, by their c...view more

This Working Draft specifies an inductively coupled plasma optical emission spectrometric method for the determination of the chromium content (mass fraction) between 5,0 % (m/m) and 27,0 % (m/m) in alloyed steels.
The method doesn't apply to alloyed steels having niobium and/or tungsten contents higher than 0,1 %.

This document specifies a flame atomic absorption spectrometric method (FAAS) for the determination of lead content in non-alloy and low alloy steels.
The method is applicable to lead contents between 0,005 % and 0,5 %.
The method can be adapted to lower or higher lead contents by changing the test portion or the dilution process, provided the criteria in 5.2.2 and 5.2.3 are still met.

This document specifies a flame atomic absorption spectrometric method (FAAS) for the determination of calcium content in non-alloy and low alloy steels.
The method is applicable to calcium contents between 0,000 4 % and 0,012 %.
The method can be adapted to higher calcium contents by changing the test portion or the dilution process, provided the criteria in 5.2.2 and 5.2.3 are still met.

This document specifies a method of classifying the microstructure of graphite in cast irons by comparative visual analysis. The purpose of this document is to provide information about the method of graphite classification. It is not intended to give information on the suitability of cast-iron types and grades for any particular application. The particular material grades are specified mainly by mechanical properties and, in the case of austenitic and abrasion resistant cast irons, by their che...view more

This document specifies an inductively coupled plasma optical emission spectrometric method for the determination of the chromium content (mass fraction) between 5,0 % (m/m) and 27,0 % (m/m) in alloyed steels.
The method doesn't apply to alloyed steels having carbon contents higher than 1 % and niobium and/or tungsten contents higher than 0,1 %.