87.060 - Paint ingredients

This document specifies the requirements and the corresponding test methods for three types of lithopone pigments.

This document specifies a method for determining the total content of polychlorinated biphenyls (PCBs), checking for all 209 possible congeners in pigment materials.
This document is applicable to a working range from1 mg/kg to 150 mg/kg. The lower quantitation limit of this method is 1 mg/kg per congener. Results below 1 mg/kg are considered to be qualitative only.

This document specifies a method for experimental determination of the release of nanoscale pigments and extenders into the environment following a mechanical stress of paints, varnishes and pigmented plastics.
The method is used to evaluate if and how many particles of defined size and distribution under stress (type and height of applied energy) are released from surfaces and emitted into the environment.
The samples are aged, weathered or otherwise conditioned to simulate the whole lifecycl...view more

This document specifies procedures for the sampling of paints and varnishes, including coating
powders, and raw materials used in their manufacture. Such products include liquids and materials
which, without undergoing chemical modification, are capable of being liquefied when heated up, and
powdered, granulated and pasty materials. Samples can be taken from containers, for example cans,
drums, tanks, tank wagons or ships' tanks, as well as from barrels, sacks, big-bags, silos or silo wagons...view more

This document specifies a titrimetric method for determining the hydroxyl groups in resins and binders for paints and varnishes.
This method is primarily suitable for neutral media. Acidic products provide higher values; neutral products provide, through neutralization of the acidic carbamates, lower values. For these products, preliminary tests are performed to ensure the applicability of the method.

This document specifies the test methods for determining the softening point of resins (including rosin)
and similar materials by means of ring-and-ball apparatus.
Both manual and automated methods are specified, the automated method being the reference method.

This document specifies a formalism for the calculation of the illuminant metamerism of solid surface colours. It cannot be applied to colours of effect coatings without metrical adaptation. This document only covers the phenomenon of metamerism for change of illuminant, which has the greatest meaning in practical application. In the case of chromaticity coordinates of a pair of samples under reference conditions that do not exactly match, recommendations are given on which correction measures a...view more

This document specifies the determination of the molar-mass distribution and the average molar mass values Mn (number average) and Mw (weight average) of polymers that are soluble in tetrahydrofuran (THF) by gel permeation chromatography (GPC). NOTE Also known as size exclusion chromatography (SEC). Even though the chromatograms obtained show good repeatability, it is possible that this method cannot be used with certain polymer types because of specific interactions (e.g. adsorption) within the...view more

This document specifies the determination of the molar-mass distribution and the average molar mass values Mn (number average) and Mw (weight average) of polymers that are soluble in water by gel permeation chromatography (GPC). NOTE Also known as size exclusion chromatography (SEC). This method is applicable to neutral polymers and polyanions (e.g. polycarboxylates, polysaccharides, fully hydrolyzed polyvinyl alcohols and high-molecular polyethylene oxides). It is not applicable to polycations ...view more

This document specifies the determination of the molar-mass distribution and the average molar mass values Mn (number average) and Mw (weight average) of polymers that are soluble in DMAC (N,N-Dimethylacetamide) by gel permeation chromatography (GPC). NOTE Also known as size exclusion chromatography (SEC). Even though the chromatograms obtained show good repeatability, it is possible that this method cannot be used with certain polymer types because of specific interactions (e.g. adsorption) wit...view more

EN-ISO 787-19 specifies a general method of test for determining the water-soluble nitrates in a sample of pigments by a spectrophotometric method using salicylic acid.ISO 787-13 specifies a method for determining the water-soluble nitrates in a sample of pigments using Nessler`s method.

EN-ISO 3262-1 gives the definition for the term extender and specifies test methods that are required for most of the subsequent parts of ISO 3262.

This document specifies a general method of test for determining the water-soluble nitrates in a sample of pigments by a spectrophotometric method using salicylic acid. ISO 787-13 specifies a method for determining the water-soluble nitrates in a sample of pigments using Nessler`s method.

This document gives the definition for the term extender and specifies test methods that are required for most of the subsequent parts of ISO 3262.
NOTE The subsequent parts of ISO 3262 specify requirements and the corresponding methods of test for extenders for use in paints, related coating materials and other applications.

This document gives the definition for the term extender and specifies test methods that are required for most of the subsequent parts of ISO 3262. NOTE The subsequent parts of ISO 3262 specify requirements and the corresponding methods of test for extenders for use in paints, related coating materials and other applications.

This document specifies a general method of test for determining the water-soluble sulphates, chlorides and nitrates of pigments.

This document describes a general method of test for comparing the resistance to light of samples of similar types of coloured pigments (agreed reference pigment and test sample). Two methods of exposure are described in this document. In method A, the material is exposed under glass to natural light. In method B, the material is exposed to direct artificial light.

This document specifies the requirements and the corresponding test methods for five types of linseed stand oil suitable for paints and varnishes.

This document describes a general method of test for comparing the resistance to light of samples of similar types of coloured pigments (agreed reference pigment and test sample).
Two methods of exposure are described in this document. In method A, the material is exposed under glass to natural light. In method B, the material is exposed to direct artificial light.