M/BC/CEN/88/13 - Machines: Safety of machinery
Standardization request to CEN/CENELEC relating to machinery
General Information
- 1 (current)
- 2
- 3
- 4
- 5
This document specifies a laboratory substitution method to determine the insertion loss without flow of ducted, mainly absorbent, circular and rectangular silencers, as well as other duct elements for use in ventilating and air-conditioning systems.
NOTE Laboratory measurement procedures for ducted silencers with superimposed flow are described in ISO 7235[5].
This document is applicable to silencers where the design velocity does not exceed 15 m/s. As the method does not include self-generat...view more
- Standard16 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft15 pagesEnglish language
sale 10% off- e-Library read for1 day
This standard specifies the essential safety requirements for the design, construction and use of injection moulding machines for the processing of plastics and/or rubber.
- Standard161 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft161 pagesEnglish language
sale 10% off- e-Library read for1 day
This draft European standard specifies safety requirements relating to the design and construction of calenders intended for the processing of rubber or plastics.
This draft European standard concerns the calender alone, including all components fixed to its frame.
Annex C shows examples of various types of calenders and Annex D shows examples of calendaring processes.
This draft European standard deals with all significant hazards, hazardous situations or hazardous events relevant to the des...view more
- Standard55 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft55 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment13 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment9 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-17 JF: Through decision BT C190/2019, the BT approved the removal of the link for this standard with the Machinery Directive.
2019-05-31 JF: Following the discussion at the Nucleus (core group of the CEN-CENELEC sector on machinery safety), it was concluded that this standard should not be listed in the Official Journal of European Union (OJEU) under the Machinery Directive 2006/42/EC because these are guidelines. This had been agreed with the TC. CCMC is preparing the BT document on ...view more
- Amendment9 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment5 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-17 JF: Through decision BT C190/2019, the BT approved the removal of the link for this standard with the Machinery Directive.
2019-05-31 JF: Following the discussion at the Nucleus (core group of the CEN-CENELEC sector on machinery safety), it was concluded that this standard should not be listed in the Official Journal of European Union (OJEU) under the Machinery Directive 2006/42/EC because these are guidelines. This had been agreed with the TC. CCMC is preparing the BT document on ...view more
- Amendment9 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment5 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies safety requirements relating to the design and construction of calenders (see 3.1.1) intended for the calendering, polishing, laminating or embossing of rubber or plastics.
This document concerns the calender alone, including the following integrated components: cutting device, stock guides and feeding device, secondary roller.
Annex C shows examples of various types of calenders and Annex D shows examples of calendaring processes.
This document deals with all signific...view more
- Standard55 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft55 pagesEnglish language
sale 10% off- e-Library read for1 day
This draft European standard specifies the essential safety requirements applicable to the design and construction of reaction moulding machines and plants.
The significant and specific hazards are listed in Annex A and are dealt with in this draft European standard.
This draft European standard does not cover the hazards related to the cutting unit (see EN 14886:2008).
This draft European standard does not cover the requirements for the design of exhaust systems.
This draft European standar...view more
- Standard32 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft25 pagesEnglish language
sale 10% off- e-Library read for1 day
This draft European Standard specifies the essential safety requirements applicable to the design and construction of haul-offs for cable, cable core, profiles and pipes used in extrusion lines for processing plastic and rubber for the hazards identified in Annex A. The following kinds of haul-offs are covered:
- caterpillar haul-offs;
- belt haul-offs;
- capstan haul-offs;
- belt capstan haul-offs;
- roller haul-offs.
The machine begins at the product inlet opening and ends at the product...view more
- Standard32 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft29 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies the essential safety requirements applicable to the design and construction of reaction moulding machines and plants as defined in 3.1 and 3.2.
This document deals with all significant hazards, hazardous situations or hazardous events during all phases of the machine life cycle (see EN ISO 12100:2010, 5.4), when reaction moulding machines and plants are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer (see Annex A).
A r...view more
- Standard32 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft25 pagesEnglish language
sale 10% off- e-Library read for1 day
This document deals with all significant hazards, hazardous situations and events relevant to haul-offs for cable, cable core, profiles and pipes for processing plastic and rubber, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). The hazards have been identified taking into account all phases of the machine life cycle according to EN ISO 12100:2010, 5.4.
The following kinds of haul-offs are covered:
- caterpillar ...view more
- Standard32 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft29 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies safety requirements and measures for the verification of the design and
construction of hand-held, integrally-driven combustion engine hedge trimmers (hereafter referred to
as “hedge trimmers”) designed to be used by a single operator for trimming hedges and bushes while
utilizing one or more linear reciprocating cutter blades.
This document is also applicable to ”split-boom” type hedge trimmers and to multi-purpose machines
when configured as a hedge trimmer.
It es...view more
- Standard43 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies safety requirements and measures for the verification of the design and construction of hand-held, integrally-driven combustion engine hedge trimmers (hereafter referred to as "hedge trimmers") designed to be used by a single operator for trimming hedges and bushes while utilizing one or more linear reciprocating cutter blades.
This document is also applicable to "split-boom" type hedge trimmers and to multi-purpose machines when configured as a hedge trimmer.
It establ...view more
- Standard43 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the essential safety requirements applicable to the design and construction of blade granulators and shredders used to reduce the size of products made from plastics and/or rubber.
Machines considered in this European Standard begin at the outer edge of the feeding device/feed opening and end at the discharge area.
This European Standard deals with all significant hazards, hazardous situations or hazardous events that are listed in Annex A, when blade granulato...view more
- Standard27 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the essential safety requirements applicable to the design and construction of blade granulators and shredders used to reduce the size of products made from plastics and/or rubber.
Machines considered in this European Standard begin at the outer edge of the feeding device/feed opening and end at the discharge area.
This European Standard deals with all significant hazards, hazardous situations or hazardous events during all phases of the machine life cycle (see...view more
- Standard27 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of internal mixers for production and laboratory applications, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
An internal mixer begins at the feed openings and ends at the discharge opening.
Internal mixers usually do not produce explosive atmospheres. Where mate...view more
- Standard70 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of internal mixers during all phases of the machine life cycle (see EN ISO 12100:2010, 5.4), irrespective of their size and of the control modes of the feeding door and discharge door, for production and laboratory applications, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see...view more
- Standard70 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment12 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment12 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of ISO 15236 specifies the performance and constructional requirements applicable to
conveyor belts having steel cords in the longitudinal direction as reinforcement. The requirements for
construction given in Clause 6 apply to the design of single belts, as well as the design of complete type
series such as those covered in ISO 15236-2.
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
This International Standard specifies a method for determining the elastic and permanent elongation
of a conveyor belt and the calculation of the elastic modulus.
It is not applicable or valid for light conveyor belts as described in ISO 21183-1.
- Standard14 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 15236-1:2016 specifies the performance and constructional requirements applicable to conveyor belts having steel cords in the longitudinal direction as reinforcement. The requirements for construction given in Clause 6 apply to the design of single belts, as well as the design of complete type series such as those covered in ISO 15236‑2.
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 9856:2016 specifies a method for determining the elastic and permanent elongation of a conveyor belt and the calculation of the elastic modulus.
It is not applicable or valid for light conveyor belts as described in ISO 21183‑1.
- Standard14 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of ISO 14122 gives requirements for fixed ladders which are a part of a stationary machine,
and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of fixed ladder
systems.
NOTE 1 “Fixed” means of access are those mounted in such a manner (for example, by screws, nuts, welding)
that they can only be removed by the use of tools.
This part of ISO 14122 specifies minimum requirements that also apply when the same means of access
is required as the part of...view more
- Standard57 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of ISO 14122 gives general requirements for access to stationary machines and guidance about
the correct choice of means of access when necessary access to the stationary machine is not possible
directly from the ground level or from a floor.
It is applicable to permanent means of access which are a part of a stationary machine, and also to nonpowered
adjustable parts (e.g. foldable, slidable) and movable parts of fixed means of access.
NOTE 1 “Fixed” means of access are those mou...view more
- Standard19 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of ISO 14122 gives requirements for non-powered stairs, stepladders and guard-rails which
are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and
movable parts of those fixed means of access.
NOTE 1 “Fixed” means of access are those mounted in such a manner (for example, by screws, nuts, welding)
that they can only be removed by the use of tools.
This part of ISO 14122 specifies minimum requirements that also apply when the same me...view more
- Standard31 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of ISO 14122 gives requirements for non-powered working platforms and walkways which
are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, sliding) and
movable parts of those fixed means of access.
NOTE 1 “Fixed” means of access are those mounted in such a manner (for example, by screws, nuts, welding)
that they can only be removed by the use of tools.
This part of ISO 14122 specifies minimum requirements that also apply when the same means of...view more
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 14122-2:2016 gives requirements for non-powered working platforms and walkways which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, sliding) and movable parts of those fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-2:2016 specifies minimum requirements that also apply when the same means of access is requ...view more
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 14122-1:2016 gives general requirements for access to stationary machines and guidance about the correct choice of means of access when necessary access to the stationary machine is not possible directly from the ground level or from a floor.
It is applicable to permanent means of access which are a part of a stationary machine, and also to non-powered adjustable parts (e.g. foldable, slidable) and movable parts of fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in ...view more
- Standard19 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 14122-4:2016 gives requirements for fixed ladders which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of fixed ladder systems.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-4:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or...view more
- Standard57 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 14122-3:2016 gives requirements for non-powered stairs, stepladders and guard-rails which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of those fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-3:2016 specifies minimum requirements that also apply when the same means of access i...view more
- Standard31 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies electrical and flammability safety requirements for general purposeconveyor belts not intended for use in underground installations and a means of categorizing conveyor belts interms of the level of safety sought in their end use application. This European Standard does not provide
electrical safety requirements for volume resistance which may be measured by the methods in
EN ISO 21178 and which is relevant to some types of light conveyor belts.
This European ...view more
- Standard14 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies electrical and flammability safety requirements for general purpose conveyor belts not intended for use in underground installations and a means of categorizing conveyor belts in terms of the level of safety sought in their end use application. This European Standard does not provide electrical safety requirements for volume resistance which may be measured by the methods in EN ISO 21178 and which is relevant to some types of light conveyor belts.
This European ...view more
- Standard14 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard applies to the tyre curing presses as defined in 3.36 having the following configuration.
- Crossing flow tyre curing presses, with two cavities with:
- common curing cycle and common safeguarding; or
- independent curing cycles and common safeguarding; or
- independent curing cycles and independent safeguarding.
- Tyre curing presses with one cavity.
- Tyre curing presses with automatic rear feeding and discharge.
The requirements and/or safety meas...view more
- Draft71 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard71 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard applies to tyre curing machines having the following configuration.
- crossing flow tyre curing machines, with two cavities with:
- common curing cycle and common safeguarding; or
- independent curing cycles and common safeguarding; or
- independent curing cycles and independent safeguarding.
- tyre curing machines with one cavity.
- tyre curing machines with automatic rear feeding and discharge.
The safety requirements and/or protective measures specified in this E...view more
- Draft71 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard71 pagesEnglish language
sale 10% off- e-Library read for1 day
This standard covers the essential health and safety requirements for two roll mills for the processing of rubber and/or plastics. Significant hazards are listed in clause 4 and are covered by this standard.
This standard does not cover requirements for the design of a local exhaust ventilation system.
This document is not applicable to two roll mills manufactured before the date of its publication as an European Standard.
- Draft34 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard40 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard deals with all significant hazards, hazardous situations and events relevant to two-roll mills for the processing of rubber and/or plastics, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard covers two-roll mills as defined in 3.1.
This European Standard does not deal with the design of a local exhaust ventilation system that may be necessary in specific applications o...view more
- Draft34 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard40 pagesEnglish language
sale 10% off- e-Library read for1 day
EN ISO 11200 is the frame standard introducing the basic group, ISO 11201, ISO 11202, ISO 11203, ISO 11204 and ISO 11205, on the determination of emission sound pressure levels at work stations and other specified positions. It gives guidance for: - facilitating the writing of noise test codes; - providing physical explanations of this noise emission quantity compared to other noise quantities (see 4.1 to 4.3); - comparing the different measurement methods offered by the group (see Table 1); - f...view more
- Standard47 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 2 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. It concerns machines as listed in ISO 2187 for: - opening, cleaning, blending; - wool scouring; - baling;...view more
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 5 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. It concerns machines as listed in ISO 2544 for: - warping, - beaming, - sizing.
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 3 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. Nonwoven lines comprise machines for: - preparation (bale breaker, automated blending bale opener, cardin...view more
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 7 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. It concerns machines used for the following processes (see ISO 1506): - preparation; - dyeing; - printing...view more
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 6 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. It concerns machines for: weaving (as listed in ISO 5247), etc.
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This standard specifies all the information necessary to carry out efficiently and under standardized conditions the determination, declaration and verification of the basic noise emission quantities of groups of textile machinery. It specifies noise measurement methods, mounting and operation conditions that shall be used for the test.
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
This Part 4 of the standard is a complement to Part 1 and specifies, together with it, the mounting, operating and measuring conditions required for the measurement, declaration and verification of noise emitted by different types of spinning preparatory and spinning machines. It is applicable to engineering methods (grade 2) and survey methods (grade 3) defined in the standards referred to. It concerns machines for: - yarn processing (e.g. doubling, twisting and texturing machines, reeling and ...view more
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
EN 289 specifies the essential safety requirements for compression moulding machines and transfer moulding machines for the moulding of plastics and/or rubber with a closing movement more than 6 mm. In this document a compression moulding machine or transfer moulding machine as described above is designated by the term “press”. This document deals with all significant hazards, hazardous situations and events relevant to presses, when they are used as intended and under conditions of misuse which...view more
- Draft52 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard50 pagesEnglish language
sale 10% off- e-Library read for1 day
2013-08-21 EMA: Draft for // vote received in ISO/CS (see notification of 2013-08-20 in dataservice).
2012-11-08 GVN: Draft for // ENQ available at ISO/CS (see notification in dataservice on 2012-11-07)
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
2013-08-21 EMA: Draft for // vote received in ISO/CS (see notification of 2013-08-20 in dataservice).
2012-11-08 GVN: Draft for // ENQ available at ISO/CS (see notification in dataservice on 2012-11-07)
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
2013-08-21 EMA: Draft for // vote received in ISO/CS (see notification of 2013-08-20 in dataservice).
2012-11-08 GVN: Draft for // ENQ available at ISO/CS (see notification in dataservice on 2012-11-07)
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
2013-08-21 EMA: Draft for // vote received in ISO/CS (see notification of 2013-08-20 in dataservice).
2012-11-08 GVN: Draft for // ENQ available at ISO/CS (see notification in dataservice on 2012-11-07)
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- Amendment8 pagesEnglish language
sale 10% off- e-Library read for1 day
- 1 (current)
- 2
- 3
- 4
- 5