This part of EN 13674 specifies switch and crossing rails that carry railway wheels. These are used in conjunction with Vignole railway rails. This part of this standard is not applicable for the check rails that do not carry railway wheels. Eight pearlitic steel grades are specified covering a hardness range of 200 HBW to 390 HBW and include non heat treated non-alloy steels, non heat treated alloy steels, heat treated non-alloy steels and heat treated low alloy steels. There are !34 rail profiles" specified in this standard, but they may not all be available in all steel grades. Rails specified in EN 13674-1 may also be used as switch and crossing rails and if so used they shall comply with the requirements of EN 13674-1.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies switch and crossing rails that carry railway wheels. These are used in conjunction with Vignole railway rails.
This document is not applicable for the check rails that do not carry railway wheels.
Nine pearlitic steel grades are specified covering a hardness range of 200 HBW to 410 HBW and include non-heat treated non-alloy steels, non-heat treated alloy steels, heat treated non-alloy steels, heat treated low alloy steels and heat treated alloy steels.
There are 33 rail profiles specified in this standard, but they may not all be available in all steel grades.
Rails specified in EN 13674-1 can also be used as switch and crossing rails and if so used they will comply with the requirements of EN 13674-1.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard defines an harmonized way to assess the braking performance by test of locomotives, passenger coaches, freight wagons and self-propelled passenger trains (EMU/DMU).
The European Standard sets out the standardized method for undertaking brake performance tests and the correction factors to be applied to the data obtained for all types of rolling stock.
This European Standard also defines the methods to assess the brake performance in terms of stopping distance, and from this the process to determine vehicle(s) deceleration and brake weight.
It then deals with conversion of the brake weight to the brake weight percentage of a vehicle or train for operating purposes. It also sets out additional factors when determining the brake weight percentage of a train calculated from specified brake weight, depending on the formation of the train.
In Annex D there is a method for determining brake performance of freight wagons fitted with P10 cast iron using limited testing (force measurement).

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to the measurement of vertical wheel forces of railway vehicles in maintenance workshops and at manufacturing sites. It also deals with derived quantities that are used to describe the vehicle’s vertical wheel force distribution.
The standard defines the assessment and acceptance criteria for the measurement process. The requirements for this assessment support the specification, the design and the operation of the measurement process. It is considered that the measurements are made either statically or quasi-statically. This standard is applicable to all railway vehicles.
The commercial weighing of vehicles is not covered by the scope of this standard, nor does it define in which cases the wheel forces of a vehicle will be measured.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines a harmonized way to assess the braking performance by test of locomotives, passenger coaches, freight wagons and self-propelled passenger trains (EMU/DMU).
The document sets out the standardized method for undertaking brake performance tests and the correction factors to be applied to the data obtained for all types of rolling stock.
This document also defines the methods to assess the brake performance in terms of stopping distance, and from this the process to determine vehicle(s) deceleration and braked weight.
It then deals with conversion of the braked weight to the braked weight percentage of a vehicle or train for operating purposes. It also sets out additional factors when determining the braked weight percentage of a train calculated from specified braked weight, depending on the formation of the train.
In Annex D there is a method for determining brake performance of freight wagons fitted with P10 cast iron or LL-blocks using limited testing (force measurement).

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies flat bottom Vignole railway rails from 27 kg/m to, but excluding 46 kg/m.
Seven pearlitic steel grades are specified covering a rail hardness range of 200 HBW to 410 HBW and include non-heat-treated non-alloy steels, non-heat-treated alloy steels, heat-treated non-alloy steels and heat treated alloy steels.
There are 15 rail profiles specified in this European Standard, but these may not be available in all steel grades.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to the measurement of vertical wheel forces of railway vehicles in maintenance workshops and at manufacturing sites. It also deals with derived quantities that are used to describe the vehicle’s vertical wheel force distribution.
The document defines the assessment and acceptance criteria for the measurement process. The requirements for this assessment support the specification, the design and the operation of the measurement process. It is considered that the measurements are made either statically or quasi-statically. This document is applicable to all railway vehicles.
The commercial weighing of vehicles is not covered by the scope of this document, nor does it define in which cases the wheel forces of a vehicle will be measured.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies flat bottom Vignole railway rails from 27 kg/m to, but excluding 46 kg/m.
Eight pearlitic steel grades are specified covering a rail hardness range of 200 HBW to 440 HBW and include non-heat-treated non-alloy steels, non-heat-treated alloy steels, heat-treated non-alloy steels and heat-treated alloy steels.
There are 15 rail profiles specified in this document, but these may not be available in all steel grades.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies test methods and acceptance criteria for a brake system used in passenger coaches and driving trailers for use in general operation.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies test methods and acceptance criteria for a brake system used in passenger coaches including driving trailers for use in general operation.
This document is applicable to all new passenger coaches including driving trailers, which are designed for general operation in the European conventional rail system network in accordance with EN 14198.
This document does not cover the homologation tests of any brake component.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard gives design rules and guidance in order to ensure a proper visibility, luminance and contrast of screens, controls and indicators in the cab in all operating conditions (day, night, natural or artificial incidental lighting).
It covers two aspects:
   Necessary characteristics of the screens, controls and indicators in order to ensure a proper visibility: range of luminance and contrast, and possibility of adjustment of perceived brightness.
   Rules for installation of the screens, keyboards, controls and indicators in the cab and on the driver’s desk: position, angle of visibility, etc. with consideration of the normal driving position and of the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.).

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable for Electrical Multiple Units (EMU), Diesel Multiple Units (DMU), Railcars, Locomotives, Driving Trailers (Driving Coaches).
NOTE 1   This European Standard applies to rolling stock in the scope of the Directive 2008/57/EC [1].
This part of EN 16186 applies to driver's desks installed on the left, on the right, or in a central position in the driver’s cab.
NOTE 2   For OTMs, see EN 14033-1 [5] and EN 15746-1 [6].
This European Standard gives design rules and guidance in order to ensure proper visibility, luminance and contrast of screens, controls and indicators in the cab in all operating conditions (day, night, natural or artificial incidental lighting).
It covers four aspects:
-   necessary characteristics of the displays, controls and indicators in order to ensure proper visibility: range of luminance and contrast, and possibility of adjustment of perceived brightness;
-   rules for positioning of the displays, keyboards, controls and indicators in the cab and on the driver’s desk: position, angle of visibility, etc. with consideration of the normal driving position and of the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.);
-   necessary characteristics and rules for positioning of microphone and loudspeaker;
-   design of symbols.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   General
This European Standard defines the specific technical railway requirements for running of machines and other vehicles used for construction, maintenance and inspection of track, structures, track formation and fixed electric traction equipment.
This European Standard applies to all railbound machines and other vehicles – referred to as machines – running exclusively on the railway (utilising adhesion between the rail and wheels) and used for construction, maintenance and inspection of track, structures, infrastructure and fixed electric traction equipment. This European Standard applies to machines that are intended to operate signalling and control systems. Other machines are dealt with in other European Standards, see Annex K.
Special requirements can apply for running on infrastructures with narrow gauge or broad gauge lines, lines of tramways, railways utilising other than adhesion between the rail and wheels, road-rail machines and underground infrastructures.
This European Standard covers the requirements for safety and access of railway traffic, railway specific requirements for running on different infrastructures in relation to necessary movements of the machine as a train and movements to reach work sites.
1.2   Validity of the European Standard
This European Standard applies to new designs taking into consideration the recommendations given in Annex L on the application of the standard (migration rule).

  • Standard
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM Use’ requirements, ‘for obstacle free routes’ applying to Infrastructure on the Trans-European Network (TEN) and the assessment of those requirements. The following applies for this standard.
   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by people with reduced mobility as defined in TSI PRM.
   This standard defines elements which are universally valid for obstacle free routes. The definitions and requirements of this standard are to be used for infrastructure applications.
   This standard covers those requirements relating to Obstacle free routes.
   The standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions for specific components and systems.
   This standard assumes that the infrastructure is in the defined operating condition, any damages or operating failures will not be taken into account when assessing these requirements.
   This standard will describe these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM Use’ requirements for obstacle-free routes applying to infrastructure and the assessment of those requirements. The following applies to this European Standard:
-   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   This European Standard defines elements which are universally valid for obstacle-free routes. The definitions and requirements of this European Standard should be used for infrastructure applications;
-   This European Standard only refers to aspects of accessibility for PRM passengers, it does not define general requirements and general definitions;
-   This European Standard assumes that the infrastructure is in the defined operating condition;
-   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
This European Standard contains requirements relating to 'Obstacle-free routes'.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard defines the specific technical railway requirements for running of machines and other vehicles used for construction, maintenance and inspection of track, structures, track formation and fixed electric traction equipment. Special national conditions applicable to specific member states are shown in Annex B.
This European Standard applies to all railbound machines and other vehicles - referred to as machines - running exclusively on the railway (utilizing adhesion between the rail and wheels) and used for construction, maintenance and inspection of track, structures, infrastructure and fixed electric traction equipment.
This European Standard applies to machines that are intended to operate signalling and control systems. Other machines are dealt with in other European Standards, see Annex I.
This European Standard is written for 1 435 mm nominal track gauge; special requirements can apply for running on infrastructures with narrow gauge or broad gauge lines, urban railways, railways utilizing other than adhesion between the rail and wheels and road-rail machines which are not included in this standard.
This European Standard covers the railway specific requirements for movements of the machine as a train and movements to reach work sites.

  • Standard
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM Use’ requirements applying to rolling stock on the Trans-European Network (TEN) covered by the TSI for PRM and the assessment of those requirements. The following applies to this standard.
The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by people with reduced mobility as defined in TSI PRM.
This standard defines elements which are universally valid for obstacle free travelling including steps for access and egress and boarding aids. The definitions and requirements of this standard are used for rolling stock applications.
This part of the standard covers those requirements relating to ‘Boarding Aids’.
The standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions for specific components and systems.
This standard assumes that the vehicle is in the defined operating condition, any damages or operating failures will not be taken into account when assessing these requirements.
Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The following areas of ‘Accessibility of People with Reduced Mobility to rolling stock’ are covered in 2 parts:
   Part 1 contains
   Steps for Access and Egress
   Part 2 contains
   Boarding aids
This standard describes these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM Use’ requirements applying to rolling stock on the Trans-European Network (TEN) covered by the TSI for PRM and the assessment of those requirements. The following applies to this standard.
-   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by people with reduced mobility as defined in TSI PRM.
-   This standard defines elements which are universally valid for obstacle free travelling including steps for access and egress and boarding aids. The definitions and requirements of this standard are to be used for rolling stock applications.
-   This part of the standard covers those requirements relating to ‘Steps for Egress and Access’.
-   The standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions for specific components and systems.
-   This standard assumes that the vehicle is in the defined operating condition, any damages or operating failures will not be taken into account when assessing these requirements.
-   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements
The following areas of ‘Accessibility of People with Reduced Mobility to rolling stock’ from TSI PRM are covered in 2 parts:
-   Part 1 contains
Steps for Access and Egress
-   Part 2 contains
Boarding aids
This standard describes these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
-   The definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   This standard defines elements which are universally valid for obstacle free travelling including steps for access and egress and boarding aids. The definitions and requirements of this standard are to be used for rolling stock applications;
-   This standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions;
-   This standard assumes that the vehicle is in the defined operating condition;
-   Where minimum or maximum dimensions are quoted these are absolute NOT nominal
The ‘Accessibility of persons with reduced mobility’ standard is written in two parts:
-   This document is Part 1 and contains:
-   Steps for access and egress
-   Part 2 contains
-   Boarding aids.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
-   the definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   this standard defines elements which are universally valid for obstacle free travelling including steps for access and egress and boarding aids. The definitions and requirements of this standard are to be used for rolling stock applications;
-   this standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions;
-   this standard assumes that the vehicle is in the defined operating condition;
-   where minimum or maximum dimensions are quoted these are absolute NOT nominal.
The ‘Accessibility of persons with reduced mobility’ standard is written in two parts:
-   Part 1 contains:
-   steps for access and egress.
-   this document is Part 2 and contains:
-   boarding aids.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard describes the specific ‘Design for PRM Use’ requirements applying to rolling stock on the Trans-European Network (TEN) covered by the TSI for PRM and the assessment of those requirements. The following applies to this standard.
   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by people with reduced mobility as defined in TSI PRM.
   This standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting/standing/moving and passageways/internal doors. The definitions and requirements of this standard are to be used for rolling stock applications.
   This part of the standard covers those requirements relating to sitting, standing and moving about the train.
   The standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions for specific components and systems.
   This standard assumes that the vehicle is in the defined operating condition, any damages or operating failures shall not be taken into account when assessing these requirements.
The following areas of ‘Equipment and Components’ from TSI PRM are covered in 3 parts:
   Part 1 contains
   Toilets
   Part 2 contains
   Handholds
   Seats
   Wheelchair spaces
   Part 3 contains
   Passage ways
   Internal Doors
This standard describes these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to
both infrastructure and rolling stock and the assessment of those requirements. The following
applies to this standard:
— The definitions and requirements describe specific aspects of ‘Design for PRM use’ required
by persons with disabilities and persons with reduced mobility as defined in the PRM TSI.
— This standard defines elements which are universally valid for obstacle free travelling
including lighting, contrast, tactile feedback, transmission of visual and acoustic
information. The definitions and requirements of this standard cover the infrastructure and
the rolling stock applications.
— This standard only refers to aspects of accessibility for PRM passengers it does not define
non PRM related requirements and definitions.
— This standard assumes that the infrastructure or rolling stock is in its defined operating
condition.
— Where minimum or maximum dimensions are quoted these are absolute NOT nominal
requirements.
The ‘General requirements’ standard is written in three parts:
— Part 1 contains
— contrast;
— This document is Part 2 and contains
— spoken information;
— written information;
— tactile information;
— pictograms;
— Part 3 contains
— lighting;
— low reflective properties;
— transparent obstacles;
— slip resistance.
Terms and definitions for systems and components
The task is to describe clear and consistent terms and definitions. Where measurement methods and/or assessment procedures are needed to allow a clear pass/fail assessment, this task shall be done as well.
Existing European standards shall be taken into account for this work.

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to
both infrastructure and rolling stock and the assessment of those requirements. The following
applies to this standard:
— The definitions and requirements describe specific aspects of ‘Design for PRM use’ required
by persons with disabilities and persons with reduced mobility as defined in the PRM TSI.
— This standard defines elements that are universally valid for obstacle free travelling
including lighting, contrast, tactile feedback, transmission of visual and acoustic
information. The definitions and requirements of this standard cover the infrastructure and
rolling stock applications.
— This standard only refers to aspects of accessibility for PRM passengers it does not define
non PRM related requirements and definitions.
— This standard assumes that the infrastructure or rolling stock is in its defined operating
condition.
— Where minimum or maximum dimensions are quoted these are absolute NOT nominal
requirements.
The ‘General requirements’ standard is written in three parts:
— This document is Part 1 and contains
— contrast;
— Part 2 contains
— spoken information;
— written information;
— tactile information;
— pictograms;
— Part 3 contains
— lighting;
— low reflective properties;
— transparent obstacles;
— slip resistance.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard describes the specific ‘Design for PRM Use’ requirements applying to rolling stock on the trans-European network (TEN) covered by the TSI for PRM and the assessment of those requirements. The following are valid for this standard.
   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by people with reduced mobility as defined in TSI PRM.
   This standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting/standing/moving and passageways/internal doors. The definitions and requirements of this standard shall be used for rolling stock applications.
   This part of the standard covers those requirements relating to "Toilets".
   The standard only refers to aspects of accessibility for PRM passengers it does not define general requirements and general definitions for specific components and systems.
   This standard assumes that the vehicle is in the defined operating condition, any damages or operating failures will not be taken into account when assessing these requirements.
   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The following areas of ‘Equipment and Components’ from TSI PRM are covered in 3 parts which contain:
   Part 1
   Toilets
   Part 2
   Handholds
   Seats
   Wheelchair spaces
   Part 3
   Passageways
   Internal Doors
This standard will describe these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard describes the specific "Design for PRM Use" requirements applying to rolling stock on the trans-European network (TEN) covered by the TSI for PRM and the assessment of those requirements. The following are valid for this standard:
   the definitions and requirements describe specific aspects of "Design for PRM Use" required by people with reduced mobility as defined in TSI PRM;
   people with reduced mobility as defined in TSI PRM;
   this standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting/standing/moving and passageways/internal doors. The definitions and requirements of this standard are to be used for rolling stock applications;
   this part of the standard covers those requirements relating to "Toilets";
   the standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions for specific components and systems;
   this standard assumes that the vehicle is in the defined operating condition, any damages or operating failures will not be taken into account when assessing these requirements;
   where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The following areas of "Equipment and Components" from TSI PRM are covered in three parts:
   Part 1 contains:
   Toilets;
   Part 2 contains:
   Handholds;
   Seats;
   Wheelchair spaces;
   Part 3 contains:
   Passage ways;
   Internal Doors.
This standard describes these areas with clear and consistent terms and definitions. Measurement methods and/or assessment procedures needed to establish a clear pass/fail assessment are provided where necessary.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard describes the specific ‘Design for PRM use’ requirements applying to
both infrastructure and rolling stock and the assessment of those requirements. The following
applies to this standard:
— The definitions and requirements describe specific aspects of ‘Design for PRM use’ required
by persons with disabilities and persons with reduced mobility as defined in the PRM TSI.
— This standard defines elements that are universally valid for obstacle free travelling
including lighting, contrast, tactile feedback, transmission of visual and acoustic
information. The definitions and requirements of this standard cover the infrastructure and
rolling stock applications.
— This standard only refers to aspects of accessibility for PRM passengers it does not define
non PRM related requirements and definitions.
— This standard assumes that the infrastructure or rolling stock is in its defined operating
condition.
— Where minimum or maximum dimensions are quoted these are absolute NOT nominal
requirements.
The ‘General requirements’ standard is written in three parts:
— Part 1 contains:
— contrast.
— Part 2 contains:
— spoken information;
— written information;
— tactile information;
— pictograms.
— This document is Part 3 and contains:
— lighting;
— low reflective properties;
— transparent obstacles;
— slip resistance.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
-   the definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   this standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications;
-   this standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions;
-   this standard assumes that the rolling stock is in its defined operating condition;
-   where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and components' standard is written in three parts:
-   Part 1 contains:
-   toilets;
-   Part 2 contains:
-   handholds;
-   seats;
-   wheelchair spaces;
-   this document is Part 3 and contains:
-   clearways;
-   internal doors.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
-   the definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   this standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications;
-   this standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions;
-   this standard assumes that the rolling stock is in its defined operating condition;
-   where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and Components' standard is written in three parts:
-   this document is Part 1 and contains:
-   toilets;
-   part 2 contains:
-   handholds;
-   seats;
-   wheelchair spaces;
-   part 3 contains:
-   clearways;
-   internal doors.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard describes the specific ‘Design for PRM use’ requirements applying to rolling stock and the assessment of those requirements. The following applies to this standard:
-   the definitions and requirements describe specific aspects of ‘Design for PRM use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI;
-   this standard defines elements which are universally valid for obstacle free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications;
-   this standard only refers to aspects of accessibility for PRM passengers. It does not define general requirements and general definitions;
-   this standard assumes that the rolling stock is in its defined operating condition;
-   where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The 'Equipment and components' standard is written in three parts:
-   Part 1 contains:
-   toilets;
-   this document is Part 2 and contains:
-   handholds;
-   seats;
-   wheelchair spaces;
-   Part 3 contains:
-   clearways;
-   internal doors.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Introduction
Based on the Directive 2001/16/EC modified by Directive 2004/50/EC of the European Community and additional activities of a number of EC member states concerning "Obstacle-free Travelling" ERA published a Technical Specification Interoperability for "People with Reduced Mobility (PRM)" which was mandated by the EC. The objective of this TSI is to enhance the accessibility of rail transport to these persons.
The definition of People with Reduced Mobility is in accordance with clause 2.2 of the TSI PRM.
General
-   The definitions and requirements shall describe the utilisation of information by people with reduced mobility especially for people with hearing, visual or communication impairments.
-   This standard defines elements which are universally valid for obstacle free travelling such as lighting, contrast, tactile feedback, transmission of visual and acoustic information. The definitions and requirements of this standard shall be used for infrastructure as well as rolling stock applications.
-   The standard shall define aspects of accessibility (to Infrastructure and Rolling Stock) specifically required by PRM users, it shall not define general requirements and definitions applicable to all users.
-   For preparing the terms and definitions well-defined operating conditions are to be considered. Any damages or operating trouble e.g. failures of parts of the lighting system will not be taken into account.
Definition of systems and components
-   Part 1 Contrast
Terms and definitions for systems and components
The task is to describe clear and consistent terms and definitions. Where measurement methods and/or assessment procedures are needed to allow a clear pass/fail assessment, this task shall be done as well.
Existing European standards shall be taken into account for this work.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Introduction
Based on the Directive 2001/16/EC modified by Directive 2004/50/EC of the European Community and additional activities of a number of EC member states concerning "Obstacle-free Travelling" ERA published a Technical Specification Interoperability for "People with Reduced Mobility (PRM)" which was mandated by the EC. The objective of this TSI is to enhance the accessibility of rail transport to these persons.
The definition of People with Reduced Mobility is in accordance with clause 2.2 of the TSI PRM.
General
-   The definitions and requirements shall describe the utilisation of information by people with reduced mobility especially for people with hearing, visual or communication impairments.
-   This standard defines elements which are universally valid for obstacle free travelling such as lighting, contrast, tactile feedback, transmission of visual and acoustic information. The definitions and requirements of this standard shall be used for infrastructure as well as rolling stock applications.
-   The standard shall define aspects of accessibility (to Infrastructure and Rolling Stock) specifically required by PRM users, it shall not define general requirements and definitions applicable to all users.
-   For preparing the terms and definitions well-defined operating conditions are to be considered. Any damages or operating trouble e.g. failures of parts of the lighting system will not be taken into account.
Definition of systems and components
-   Part 2 Information
o   Spoken information
o   Written information
o   Tactile feedback
o   Pictograms
Terms and definitions for systems and components
The task is to describe clear and consistent terms and definitions. Where measurement methods and/or assessment procedures are needed to allow a clear pass/fail assessment, this task shall be done as well.
Existing European standards shall be taken into account for this work.

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard describes the specific ‘Design for PRM Use’ requirements applying to both infrastructure and rolling stock and the assessment of those requirements. The following applies to this standard:
-   The definitions and requirements describe specific aspects of ‘Design for PRM Use’ required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI.
-   This standard defines elements which are universally valid for obstacle free travelling including lighting, contrast, tactile feedback, transmission of visual and acoustic information. The definitions and requirements of this standard are to be used for infrastructure and rolling stock applications.
-   This standard only refers to aspects of accessibility for PRM passengers it does not define non PRM related requirements and definitions.
-   This standard assumes that the infrastructure or rolling stock is in its defined operating condition.
-   Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements.
The ‘General Requirements’ standard is written in three parts:
-   Part 1 contains:
-   contrast.
-   Part 2 contains:
-   spoken information;
-   written information;
-   tactile information;
-   pictograms.
-   This document is Part 3 and contains:
-   lighting;
-   low reflecting properties;
-   transparent obstacles;
-   slip resistance.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard defines the activities related to work on or near the railway track and the associated competence profiles of persons who carry out these activities and defines procedures for assessing the competence.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document defines minimum functional and non-functional requirements for developing a Track Warning Systems (TWS) to warn persons during their work on or nearby the track about the approaching of trains or rail vehicles using acoustical and visual TWS-Signals. These systems may also be able to influence the approaching of trains and rail vehicles by stoppage function.
This European Standard is applicable:
- to systems, sub-systems and components within TWS, including those containing software; in particular;
- to new TWS;
- to new integrations of systems, sub-systems and components into existing TWS;
- to modifications of TWS developed according to this standard.
For single warning units (e.g. simple electrical horns) it is recommended to use this standard, too.
This document does not deal with:
- hazards during the installation of the TWS caused by trains or rail vehicles on the lines;
- hazards caused by the improper use of TWS;
- hazards caused by the improper behaviour of persons working on or nearby the track;
- CO2-tyfone, human operated pressure signal horns, flags, detonators or machine warning systems according to UIC 644;
- national safety regulations to plan and operate TWS in track.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard defines the activities related to work on or near the railway track and the associated competence profiles of persons who carry out these activities and defines procedures for assessing the competence.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard defines minimum functional and non-functional requirements for developing a Track Warning Systems (TWS) to warn persons during their work on or nearby the track about the approaching of trains or rail vehicles using acoustical and visual TWS-Signals. These systems may also be able to influence the approaching of trains and rail vehicles by stoppage function.
This European Standard is applicable:
- to systems, sub-systems and components within TWS, including those containing software; in particular;
- to new TWS;
- to new integrations of systems, sub-systems and components into existing TWS;
- to modifications of TWS developed according to this standard.
For single warning units (e.g. simple electrical horns) it is recommended to use this standard, too.
This document does not deal with:
- hazards during the installation of the TWS caused by trains or rail vehicles on the lines;
- hazards caused by the improper use of TWS;
- hazards caused by the improper behaviour of persons working on or nearby the track;
- CO2-tyfone, human operated pressure signal horns, flags, detonators or machine warning systems according to UIC 644;
- national safety regulations to plan and operate TWS in track.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies restoration of cast austenitic manganese steel for fixed crossings and cradles for crossings with movable parts, designed to be flash butt welded or bolted to adjoining rails manufactured according to EN 15689. The standard also applies to flash welded leg ends of austenitic manganese steel crossings and the associated tri-metal zone.
This standard describes the approval systems for consumables and procedures used in manual metal arc and flux cored metal deposit repair welding. The standard includes the quality-related tasks and responsibilities and qualifications of personnel involved in the electric arc repair welding of cast crossings.
The permitted welding processes are limited to Electric Arc (EA) in accordance with EN ISO 4063 and are by description Process No 111: MMA (Manual Metal Arc) and Process No 114: FCAW (self shielded tubular cored arc welding). Their applications are described.
This standard may be applied in situ, at line side or at out of track locations.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies restoration of cast austenitic manganese steel for fixed crossings and cradles for crossings with movable parts, designed to be flash butt welded or bolted to adjoining rails manufactured according to EN 15689. The standard also applies to flash welded leg ends of austenitic manganese steel crossings and the associated tri-metal zone.
The standard specifies the approval systems for consumables and procedures used in manual metal arc and flux cored metal deposit repair welding. The standard includes the quality-related tasks and responsibilities and qualifications of personnel involved in the electric arc repair welding of cast crossings.
The permitted welding processes are limited to Electric Arc (EA) in accordance with EN ISO 4063, specifically Process No 111: MMA (Manual Metal Arc) and Process No 114: FCAW (Flux Cored Arc Welding). Their applications are described.
This standard may be applied for procedures in situ, at line side or at out of track locations.
The purpose of this standard is to unify restoration of cast manganese crossings by electric arc welding across Europe. The standard provides control systems for the approval and qualification of welding processes, WPS, welding consumables, contractors and welders for the successful delivery of welds on crossings in service.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements for the design, dimensions, performance and testing of single/double brake indicators. It applies to pneumatically and electrically operating brake indicators visible from the outside of the vehicle.
NOTE 1   Brake indicators are for giving precise and accurate information about release and application of the brake.
This European Standard applies to brake indicators on railway vehicles used on the main national networks, urban networks, underground railways, trams and private networks (regional railways, company railways etc.).
NOTE 2   This document does not apply to brake indicator for magnetic track brake or eddy current brake.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements for the design, dimensions, performance and testing of single/double brake indicators. It applies to pneumatically and electrically operating brake indicators visible from the outside of the vehicle.
NOTE   Brake indicators are for giving information about release and application of the brake.
This European Standard applies to brake indicators on railway vehicles used on the main national networks, urban networks, underground railways, trams and private networks (regional railways, company railways etc.).
This document does not apply to brake indicator for magnetic track brake or eddy current brake.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 13230 defines technical criteria and control procedures for manufacturing and testing twin block reinforced concrete sleepers.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 13230 defines additional technical criteria and control procedures related to manufacturing and testing prestressed monoblock sleepers.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 13230 defines technical criteria and control procedures which have to be satisfied by the constituent materials and the finished concrete sleepers and bearers, i.e.: precast concrete sleepers, bearers for switches and crossings, and special elements for railway tracks.
The main requirement of concrete sleepers and bearers is the transmission of vertical, lateral and longitudinal loads from the rails to the ballast or other support. In use they are also exposed to frost damage and to moisture, which can result in detrimental chemical reactions within the sleeper.
In this standard mechanical tests are defined which provide assurance of the capability of sleepers or bearers to resist repetitive loading and provide sufficient durability. In addition controls are placed on manufacturing processes and tests to ensure that the concrete will not suffer degradation in service through chemical reaction and frost damage.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 13230 defines additional technical criteria and control procedures for manufacturing and testing special elements.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of the EN 13230 series defines additional technical criteria and control procedures related to the manufacturing and testing of prestressed monoblock sleepers.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of the EN 13230 series defines technical criteria and control procedures which need to be satisfied by the constituent materials and the finished concrete sleepers and bearers, i.e.: precast concrete sleepers, twin-block reinforced sleepers, bearers for switches and crossings, and special elements for railway tracks.
The main requirement of concrete sleepers and bearers is the transmission of vertical, lateral and longitudinal loads from the rails to the ballast or other support. In use, they are also exposed to frost damage and to moisture, which can result in detrimental chemical reactions within the sleeper.
In this standard mechanical tests are defined which provide assurance of the capability of sleepers or bearers to resist repetitive loading and provide sufficient durability. In addition, controls are placed on manufacturing processes and tests to ensure that the concrete will not suffer degradation in service through chemical reaction and frost damage.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of the EN 13230 series defines technical criteria and control procedures for manufacturing and testing twin-block reinforced concrete sleepers.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of the EN 13230 series defines additional technical criteria and control procedures for manufacturing and testing special elements.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The standard gives guidance for the design and defines criteria for validation of the rolling stock and its constituents under specific environmental conditions to which this rolling stock will be subject. It also includes availability, reliability and safety aspects which are relevant for the daily operation and the correct functioning of the rolling stock in these environmental conditions.
This standard applies to:
a. Self-propelling thermal or electric trains;
b. Thermal or electric traction units;
c. Passenger carriages;
d. Mobile railway infrastructure construction and maintenance equipment.
The nominal range of the environmental parameters is described in the EN 50125.

  • Technical report
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Report gives guidance for designing rolling stock for its specified ranges of environmental conditions according to EN 50125 1. This guidance covers environmental conditions in Europe.
The relevant clauses for the particular vehicle should be chosen and described in the vehicle specification. Depending on the ranges selected, design and/or testing provisions described in this Technical Report should be taken into account. This Technical Report is a collection of existing test descriptions and design guidance based on long lasting experience of operators, test centres and industry.

  • Technical report
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day