ASTM F412-16a
(Terminology)Standard Terminology Relating to Plastic Piping Systems
Standard Terminology Relating to Plastic Piping Systems
SCOPE
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included.
1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after review, by Subcommittee F17.91 to be a generally usable term.
1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC International Union of Pure and Applied Chemistry).
1.4 A definition is a single sentence with additional information included in notes.
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s) in which they are used (for example, F714).
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F412 − 16a
Standard Terminology Relating to
1
Plastic Piping Systems
ThisstandardisissuedunderthefixeddesignationF412;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* D790 Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materi-
1.1 This terminology is a compilation of definitions of
als
technical terms used in the plastic piping industry. Terms that
D882 Test Method for Tensile Properties of Thin Plastic
are generally understood or adequately defined in other readily
Sheeting
available sources are not included.
D883 Terminology Relating to Plastics
1.2 When a term is used in an ASTM document for which
D907 Terminology of Adhesives
Committee F17 is responsible it is included only when judged,
D1003 Test Method for Haze and Luminous Transmittance
after review, by Subcommittee F17.91 to be a generally usable
of Transparent Plastics
term.
D1079 Terminology Relating to Roofing and Waterproofing
1.3 Definitions that are identical to those published by other D1238 Test Method for Melt Flow Rates of Thermoplastics
by Extrusion Plastometer
ASTM committees or other standards organizations are iden-
tified with the committee number (for example, D20) or with D1488 Test Method for Amylaceous Matter in Adhesives
D1505 Test Method for Density of Plastics by the Density-
the abbreviation of the name of the organization (for example,
IUPAC International Union of Pure and Applied Chemistry). Gradient Technique
D1527 Specification for Acrylonitrile-Butadiene-Styrene
1.4 A definition is a single sentence with additional infor-
(ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn
mation included in notes.
3
2013)
1.5 Definitions are followed by the committee responsible
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic
for the standard(s) (for example, [F17.26]) and standard
Pipe, Schedules 40, 80, and 120
numbers(s) in which they are used (for example, F714).
D2104 Specification for Polyethylene (PE) Plastic Pipe,
3
Schedule 40 (Withdrawn 2010)
2. Referenced Documents
D2239 Specification for Polyethylene (PE) Plastic Pipe
2
2.1 ASTM Standards: (SIDR-PR) Based on Controlled Inside Diameter
C114 Test Methods for Chemical Analysis of Hydraulic D2241 Specification for Poly(Vinyl Chloride) (PVC)
Cement Pressure-Rated Pipe (SDR Series)
D256 Test Methods for Determining the Izod Pendulum D2282 Specification for Acrylonitrile-Butadiene-Styrene
3
Impact Resistance of Plastics (ABS) Plastic Pipe (Withdrawn 2006)
D638 Test Method for Tensile Properties of Plastics D2444 Test Method for Determination of the Impact Resis-
D648 Test Method for Deflection Temperature of Plastics tance of Thermoplastic Pipe and Fittings by Means of a
Under Flexural Load in the Edgewise Position Tup (Falling Weight)
D747 Test Method for Apparent Bending Modulus of Plas- D2447 Specification for Polyethylene (PE) Plastic Pipe,
tics by Means of a Cantilever Beam Schedules 40 and 80, Based on Outside Diameter (With-
3
drawn 2010)
D2513 Specification for Polyethylene (PE) Gas Pressure
1
This terminology is under the jurisdiction ofASTM Committee F17 on Plastic
Pipe, Tubing, and Fittings
Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial
D2661 Specification for Acrylonitrile-Butadiene-Styrene
and Terminology.
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
Current edition approved Nov. 15, 2016. Published January 2017. Originally
and Fittings
approved in 1975. Last previous edition approved in 2016 as F412 – 16. DOI:
10.1520/F0412-16A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F412 − 16a
D2666 Specification for Polybutylene (PB) Plastic Tubing F948 Test Method for Time-to-Failure of Plastic Piping
3
(Withdrawn 2003) Systems and Components Under Constant Internal Pres-
D2680 Specification for Acrylonitrile-Butadiene-Styrene sure With Flow
F1025 Guide for Selection and Use of Full-Encirclement-
(ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer
Type Band Clamps
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F412 − 16 F412 − 16a
Standard Terminology Relating to
1
Plastic Piping Systems
This standard is issued under the fixed designation F412; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope Scope*
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are
generally understood or adequately defined in other readily available sources are not included.
1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after
review, by Subcommittee F17.91 to be a generally usable term.
1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified
with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC
International Union of Pure and Applied Chemistry).
1.4 A definition is a single sentence with additional information included in notes.
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s)
in which they are used (for example, F714).
2. Referenced Documents
2
2.1 ASTM Standards:
C114 Test Methods for Chemical Analysis of Hydraulic Cement
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D883 Terminology Relating to Plastics
D907 Terminology of Adhesives
D1003 Test Method for Haze and Luminous Transmittance of Transparent Plastics
D1079 Terminology Relating to Roofing and Waterproofing
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1488 Test Method for Amylaceous Matter in Adhesives
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
3
D1527 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn 2013)
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
3
D2104 Specification for Polyethylene (PE) Plastic Pipe, Schedule 40 (Withdrawn 2010)
D2239 Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
D2241 Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
3
D2282 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Withdrawn 2006)
1
This terminology is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial and
Terminology.
Current edition approved Aug. 1, 2016Nov. 15, 2016. Published August 2016January 2017. Originally approved in 1975. Last previous edition approved in 20152016 as
F412 – 15.F412 – 16. DOI: 10.1520/F0412-16.10.1520/F0412-16A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F412 − 16a
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
3
D2447 Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter (Withdrawn 2010)
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
3
D2666 Specificati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.