Leather - Determination of degradability by micro-organisms (ISO 20136:2020)

This document specifies a test method to determine the degree and rate of aerobic biodegradation of hides and skins of different animal origin, whether they are tanned or not, through the indirect determination of CO2 produced by the degradation of collagen.
The test material is exposed to an inoculum (activated sludge from tannery wastewater) in an aqueous medium. If there is not a tannery nearby then urban wastewater can be used as the inoculum.
The conditions established in this document correspond to optimum laboratory conditions to achieve the maximum level of biodegradation. However, they might not necessarily correspond to the optimum conditions or maximum level of biodegradation in the natural medium.
In general, the experimental procedure covers the determination of the degradation degree and rate of the material under controlled conditions, which allows the analysis of the evolved carbon dioxide produced throughout the test. For this purpose, the testing equipment complies with strict requirements with regard to flow, temperature and agitation control.
This method applies to the following materials:
—     natural polymers of animal stroma (animal tissue/skins);
—     animal hides and skins tanned (leather) using organic or inorganic tanning agents;
—     leathers that, under testing conditions, do not inhibit the activity of microorganisms present in the inoculum.

Leder - Bestimmung der Abbaubarkeit durch Mikroorganismen (ISO 20136:2020)

Dieses Dokument legt ein Prüfverfahren fest, mit dem durch die indirekte Bestimmung von CO2, das durch den Abbau von Kollagen entsteht, der Grad und die Geschwindigkeit des aeroben Bioabbaus von entweder gegerbten oder ungegerbten Fellen und Häuten unterschiedlichen tierischen Ursprungs bestimmt wird.
Die Prüfsubstanz wird einem Inokulum (Belebtschlamm aus Gerbereiabwässern) in einem wässrigen Medium ausgesetzt. Wenn es keine Gerberei in der Nähe gibt, kann kommunales Abwasser als Inokulum verwendet werden.
Die in diesem Dokument festgelegten Bedingungen entsprechen den optimalen Laborbedingungen zum Erreichen des maximalen Grades des Bioabbaus. Sie entsprechen jedoch möglicherweise nicht unbedingt den optimalen Bedingungen oder dem maximalen Grad des Bioabbaus im natürlichen Medium.
Im Allgemeinen deckt das experimentelle Verfahren die Bestimmung des Grades und der Geschwindigkeit des Bioabbaus des Materials unter kontrollierten Bedingungen ab, welches die Analyse des freigesetzten Kohlenstoffdioxids, das während der gesamten Prüfung gebildet wurde, ermöglicht. Für diesen Zweck entspricht die Prüfvorrichtung den strikten Anforderungen in Bezug auf die Regelung des Durchflusses, der Temperatur sowie der Bewegung.
Dieses Verfahren gilt für die folgenden Materialien:
- natürliche Polymere von tierischem Stroma (tierisches Gewebe/tierische Häute);
- tierische Felle und Häute, gegerbt (Leder) mit organischen oder anorganischen Gerbstoffen;
- Leder, die unter Prüfbedingungen die Aktivität der im Inokulum vorhandenen Mikroorganismen nicht hemmen.

Cuir - Détermination de la dégradabilité par les micro-organismes (ISO 20136:2020)

Le présent document spécifie une méthode d'essai pour déterminer le degré et la vitesse de biodégradation aérobie de peaux de différents animaux, tannées ou non, par la détermination indirecte du CO2 produit par la dégradation du collagène.
Le matériau d'essai est exposé à un inoculum (boues activées d'eaux résiduaires de tannage) dans un milieu aqueux. En l'absence de tannerie à proximité, des eaux usées urbaines peuvent servir d'inoculum.
Les conditions établies dans le présent document correspondent aux conditions de laboratoire optimales pour obtenir le niveau maximal de biodégradation. Il se pourrait toutefois qu'elles ne correspondent pas aux conditions optimales ou au niveau maximal de biodégradation dans le milieu naturel.
De manière générale, le mode opératoire expérimental inclut la détermination du degré et de la vitesse de dégradation du matériau dans des conditions contrôlées, ce qui permet d'analyser le dégagement de dioxyde de carbone tout au long de l'essai. À cet effet, l'équipement d'essai répond à des exigences strictes concernant le contrôle du débit, de la température et de l'agitation.
La présente méthode s'applique aux matériaux suivants:
—          les polymères naturels de stromas animaux (tissus/peaux d'animaux);
—          les peaux d'animaux qui ont été tannées (cuir) en utilisant des agents de tannage organiques ou inorganiques;
—          les cuirs qui, dans les conditions d'essai, n'ont pas d'effet inhibiteur sur l'activité des micro-organismes présents dans l'inoculum.

Usnje - Ugotavljanje razgradljivosti z mikroorganizmi (ISO 20136:2020)

General Information

Status
Published
Publication Date
14-Jul-2020
Withdrawal Date
30-Jan-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Jul-2020
Completion Date
15-Jul-2020

Relations

Buy Standard

Standard
EN ISO 20136:2020 - BARVE
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 20136:2019 - BARVE
German language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20136:2020
01-september-2020
Nadomešča:
SIST EN ISO 20136:2017
Usnje - Ugotavljanje razgradljivosti z mikroorganizmi (ISO 20136:2020)
Leather - Determination of degradability by micro-organisms (ISO 20136:2020)
Leder - Bestimmung der Abbaubarkeit durch Mikroorganismen (ISO 20136:2020)
Cuir - Détermination de la dégradabilité par les micro-organismes (ISO 20136:2020)
Ta slovenski standard je istoveten z: EN ISO 20136:2020
ICS:
59.140.30 Usnje in krzno Leather and furs
SIST EN ISO 20136:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 20136:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 20136:2020


EN ISO 20136
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2020
EUROPÄISCHE NORM
ICS 59.140.30 Supersedes EN ISO 20136:2017
English Version

Leather - Determination of degradability by micro-
organisms (ISO 20136:2020)
Cuir - Détermination de la dégradabilité par les micro- Leder - Bestimmung der Abbaubarkeit durch
organismes (ISO 20136:2020) Mikroorganismen (ISO 20136:2020)
This European Standard was approved by CEN on 8 June 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20136:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 20136:2020
EN ISO 20136:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 20136:2020
EN ISO 20136:2020 (E)
European foreword
This document (EN ISO 20136:2020) has been prepared by Technical Committee ISO/IULTCS
"International Union of Leather Technologists and Chemists Societies" in collaboration with Technical
Committee CEN/TC 289 “Leather” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2021, and conflicting national standards shall
be withdrawn at the latest by January 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20136:2017.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 20136:2020 has been approved by CEN as EN ISO 20136:2020 without any modification.


3

---------------------- Page: 5 ----------------------
SIST EN ISO 20136:2020

---------------------- Page: 6 ----------------------
SIST EN ISO 20136:2020
INTERNATIONAL ISO
STANDARD 20136
IULTCS/IUC 37
Second edition
2020-06
Leather — Determination of
degradability by micro-organisms
Cuir — Détermination de la dégradabilité par les micro-organismes
Reference numbers
ISO 20136:2020(E)
IULTCS/IUC 37:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 20
...

SLOVENSKI STANDARD
oSIST prEN ISO 20136:2019
01-marec-2019
Usnje - Ugotavljanje razgradljivosti z mikroorganizmi (ISO/DIS 20136:2018)
Leather - Determination of degradability by micro-organisms (ISO/DIS 20136:2018)
Leder - Bestimmung der Abbaubarkeit durch Mikroorganismen (ISO/DIS 20136:2018)
Cuir - Détermination de la dégradabilité par les micro-organismes (ISO/DIS 20136:2018)
Ta slovenski standard je istoveten z: prEN ISO 20136
ICS:
59.140.30 Usnje in krzno Leather and furs
oSIST prEN ISO 20136:2019 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 20136:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 20136:2019


ENTWURF
EUROPÄISCHE NORM
prEN ISO 20136
EUROPEAN STANDARD

NORME EUROPÉENNE

Dezember 2018
ICS 59.140.30 Vorgesehen als Ersatz für EN ISO 20136:2017
Deutsche Fassung

Leder - Bestimmung der Abbaubarkeit durch
Mikroorganismen (ISO/DIS 20136:2018)
Leather - Determination of degradability by micro- Cuir - Détermination de la dégradabilité par les micro-
organisms (ISO/DIS 20136:2018) organismes (ISO/DIS 20136:2018)
Dieser Europäische Norm-Entwurf wird den CEN-Mitgliedern zur parallelen Umfrage vorgelegt. Er wurde vom Technischen
Komitee CEN/TC 289 erstellt.

Wenn aus diesem Norm-Entwurf eine Europäische Norm wird, sind die CEN-Mitglieder gehalten, die CEN-Geschäftsordnung zu
erfüllen, in der die Bedingungen festgelegt sind, unter denen dieser Europäischen Norm ohne jede Änderung der Status einer
nationalen Norm zu geben ist.

Dieser Europäische Norm-Entwurf wurde von CEN in drei offiziellen Fassungen (Deutsch, Englisch, Französisch) erstellt. Eine
Fassung in einer anderen Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine
Landessprache gemacht und dem CEN-CENELEC-Management-Zentrum mitgeteilt worden ist, hat den gleichen Status wie die
offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen
jugoslawischen Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland,
Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz,
Serbien, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und
Zypern.

Die Empfänger dieses Norm-Entwurfs werden gebeten, mit ihren Kommentaren jegliche relevante Patentrechte, die sie kennen,
mitzuteilen und unterstützende Dokumentationen zur Verfügung zu stellen.

Warnvermerk : Dieses Schriftstück hat noch nicht den Status einer Europäischen Norm. Es wird zur Prüfung und Stellungnahme
vorgelegt. Es kann sich noch ohne Ankündigung ändern und darf nicht als Europäischen Norm in Bezug genommen werden.


EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Rue de la Science 23, B-1040 Brüssel
© 2018 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. prEN ISO 20136:2018 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN
vorbehalten.

---------------------- Page: 3 ----------------------
oSIST prEN ISO 20136:2019
prEN ISO 20136:2018 (D)
Inhalt
Seite
Europäisches Vorwort . 3
Vorwort . 4
Einleitung . 5
1 Anwendungsbereich . 6
2 Normative Verweisungen . 6
3 Begriffe . 6
4 Symbole und Abkürzungen . 7
5 Kurzbeschreibung . 7
5.1 Beurteilung der Bioabbaubarkeit durch manuelle Titration: Verfahren A . 7
5.2 Beurte
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.