Safety of toys - Part 1: Mechanical and physical properties

Amendment 8 concerning hazardous magnets in toys

Sicherheit von Spielzeug - Teil 1: Mechanische und physikalische Eigenschaften

Sécurité des jouets - Partie 1 : Propriétés mécaniques et physiques

Varnost igrač - 1. del: Mehanske in fizikalne lastnosti - Dopolnilo A8

General Information

Status
Not Published
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
30-Jan-2009
Completion Date
30-Jan-2009

Relations

Buy Standard

Draft
EN 71-1:2006/kprA8:2008
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 71-1:2006/kprA8:2008
01-december-2008
9DUQRVWLJUDþGHO0HKDQVNHLQIL]LNDOQHODVWQRVWL'RSROQLOR$
Safety of toys - Part 1: Mechanical and physical properties - Amendment A8
Sicherheit von Spielzeug - Teil 1: Mechanische und physikalische Eigenschaften
Sécurité des jouets - Partie 1 : Propriétés mécaniques et physiques
Ta slovenski standard je istoveten z: EN 71-1:2005/prA8
ICS:
97.200.50 ,JUDþH Toys
SIST EN 71-1:2006/kprA8:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 71-1:2006/kprA8:2008

---------------------- Page: 2 ----------------------

SIST EN 71-1:2006/kprA8:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 71-1:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA8
October 2008
ICS 97.200.50

English Version
Safety of toys - Part 1: Mechanical and physical properties
Sécurité des jouets - Partie 1 : Propriétés mécaniques et Sicherheit von Spielzeug - Teil 1: Mechanische und
physiques - Amendement 8 concernant les aimants physikalische Eigenschaften
dangereux dans les jouets
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 52.
This draft amendment A8, if approved, will modify the European Standard EN 71-1:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 71-1:2005/prA8:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 71-1:2006/kprA8:2008
EN 71-1:2005/prA8:2008 (E)
Contents Page
Foreword.3
1 Modification to the Scope .4
2 Modification to Clause 3 .4
3 Addition of 4.23.4
4 Modification to 7.14 .5
5 Addition of 7.19.5
6 Addition of 8.34.5
7 Addition of 8.35.6
8 Addition of A.51.8
9 Modification to Annex ZA .10

2

---------------------- Page: 4 ----------------------

SIST EN 71-1:2006/kprA8:2008
EN 71-1:2005/prA8:2008 (E)
Foreword
This document (EN 71-1:2005/prA8:2008) has been prepared by Technical Committee CEN/TC 52 “Safety of
toys”, the secretariat of which is held by DS.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Direct
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.