iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 3611:2023

(Main)

Geometrical product specifications (GPS) - Dimensional measuring equipment - Design and metrological characteristics of micrometers for external measurements (ISO 3611:2023)

Geometrical product specifications (GPS) - Dimensional measuring equipment - Design and metrological characteristics of micrometers for external measurements (ISO 3611:2023)

This document provides the most important design and metrological characteristics of micrometers for external measurements:
—    with analogue indication;
—    with digital indication: mechanical or electronic digital display.

Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Konstruktionsmerkmale und messtechnische Merkmale von Bügelmessschrauben für die Außenmessung (ISO 3611:2023)

Dieses Dokument enthält die wichtigsten Konstruktionsmerkmale und messtechnischen Merkmale für Bügelmessschrauben:
—   mit Skalenanzeige;
—   mit Ziffernanzeige: mechanische oder elektronische Ziffernanzeige.

Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel - Caractéristiques de conception et caractéristiques métrologiques des micromètres d'extérieur (ISO 3611:2023)

Le présent document fournit les caractéristiques de conception et les caractéristiques métrologiques les plus importantes des micromètres d’extérieur:
—    avec indication analogique;
—    avec indication numérique: affichage numérique mécanique ou électronique.

Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dolžin - Konstrukcijske in meroslovne značilnosti mikrometrov za zunanje meritve (ISO 3611:2023)

Ta dokument določa najpomembnejše konstrukcijske in meroslovne značilnosti mikrometrov za zunanje meritve:
–    z analognim zapisom;
–    z digitalnim zapisom (mehanski ali elektronski prikaz).

General Information

Status
Published
Publication Date
30-May-2023
ICS
17.040.30 - Measuring instruments
17.040.40 - Geometrical Product Specification (GPS)
Technical Committee
CEN/TC 290 - Dimensional and geometrical product specification and verification
Drafting Committee
CEN/TC 290 - Dimensional and geometrical product specification and verification
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
31-May-2023
Completion Date
31-May-2023
Ref Project
SIST EN ISO 3611:2023 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Design and metrological characteristics of micrometers for external measurements (ISO 3611:2023)

Relations

Replaces
EN ISO 3611:2010 - Geometrical product specifications (GPS) - Dimensional measuring equipment: Micrometers for external measurements - Design and metrological characteristics (ISO 3611:2010)
Effective Date
19-Jan-2023

Buy Standard

EN ISO 3611:2023EN ISO 3611:2023
PreviousNext
Standard
EN ISO 3611:2023
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3611:2023
01-julij-2023
Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dolžin -
Konstrukcijske in meroslovne značilnosti mikrometrov za zunanje meritve (ISO
3611:2023)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Design
and metrological characteristics of micrometers for external measurements (ISO
3611:2023)
Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Konstruktionsmerkmale
und messtechnische Merkmale von Bügelmessschrauben für die Außenmessung (ISO
3611:2023)
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel
- Caractéristiques de conception et caractéristiques métrologiques des micromètres
d'extérieur (ISO 3611:2023)
Ta slovenski standard je istoveten z: EN ISO 3611:2023
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 3611:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3611:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 3611:2023


EN ISO 3611
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2023
EUROPÄISCHE NORM
ICS 17.040.30 Supersedes EN ISO 3611:2010
English Version

Geometrical product specifications (GPS) - Dimensional
measuring equipment - Design and metrological
characteristics of micrometers for external measurements
(ISO 3611:2023)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Équipement de mesurage dimensionnel - Längenmessgeräte - Konstruktionsmerkmale und
Caractéristiques de conception et caractéristiques messtechnische Merkmale von Bügelmessschrauben
métrologiques des micromètres d'extérieur (ISO für die Außenmessung (ISO 3611:2023)
3611:2023)
This European Standard was approved by CEN on 5 May 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3611:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3611:2023
EN ISO 3611:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3611:2023
EN ISO 3611:2023 (E)
European foreword
This document (EN ISO 3611:2023) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2023, and conflicting national standards
shall be withdrawn at the latest by November 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3611:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 10360-13:2021(Main)
Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 13: Optical 3D CMS (ISO 10360-13:2021)
SIST EN ISO 10360-13:2021

This document specifies the acceptance tests for verifying the performance of an optical 3D coordinate measuring system (CMS) when measuring lengths as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the optical 3D CMS.
This document is applicable to verification of the measuring performance of CMSs if the surface characteristics (e.g. glossiness, colour) of the object to be scanned are restricted and within a cooperative range.
This document does not apply to other types of CMSs, including those covered by the other parts of the ISO 10360 series.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10360-10:2021(Main)
Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 10: Laser trackers (ISO 10360-10:2021)
SIST EN ISO 10360-10:2021

This document specifies the acceptance tests for verifying the performance of a laser tracker by measuring calibrated test lengths, according to the specifications of the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the laser tracker. The acceptance and reverification tests given in this document are applicable to laser trackers utilizing a retroreflector, or a retroreflector in combination with a stylus or optical distance sensor, as a probing system. Laser trackers that use interferometric measurement (IFM), absolute distance measurement (ADM) or both can be verified using this document. This document can also be used to specify and verify the relevant performance tests of other spherical coordinate measurement systems that use cooperative targets, such as “laser radar” systems.
NOTE       Systems which do not track the target, such as laser radar systems, will not be tested for probing performance.
This document does not explicitly apply to measuring systems that do not use a spherical coordinate system. However, interested parties can apply this document to such systems by mutual agreement.
This document specifies:
—    performance requirements that can be assigned by the manufacturer or the user of the laser tracker;
—    the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements;
—    rules for proving comformity;
—    applications for which the acceptance and reverification tests can be used.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13385-2:2020(Main)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Design and metrological characteristics of calliper depth gauges (ISO 13385-2:2020)
SIST EN ISO 13385-2:2020

This document specifies the most important design and metrological characteristics of calliper depth gauges
—     with analogue indication: vernier scale or circular scale (dial); and
—     with digital indication: digital display.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10360-5:2020(Main)
Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 5: Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and/or scanning measuring mode (ISO 10360-5:2020)
SIST EN ISO 10360-5:2020

This document specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using:
—     any type of contacting probing system; and
—     spherical or hemispherical stylus tip(s).
NOTE    CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere.
This document applies to CMMs supplied with any of the following:
a)   single-stylus probing systems;
b)   multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. "star" stylus);
c)   multiple probing systems such as those with a stylus for each of their probes;
d)   systems with articulating probing systems;
e)   stylus and probe changing systems;
f)    manual (non-driven) and automated CMMs;
g)   installations including a scanning probe, capable of being used in a scanning mode.
This document is not applicable to non-contacting probing systems, which require different testing procedures.
The term ?combined CMM and multi-stylus probing system size error' has been shortened to ?multi-stylus size error' for convenience. This applies in similar cases.
If it is desirable to isolate the probing system performance as far as is practical, the influence of the CMM can be minimized but not eliminated. See Annex C for more information.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20170:2019(Main)
Geometrical product specifications (GPS) - Decomposition of geometrical characteristics for manufacturing control (ISO 20170:2019)
SIST EN ISO 20170:2019

This document describes principles and tools to control a manufacturing process in accordance with a GPS specification. For this purpose a set of one or more complementary, independent characteristics (size, form, orientation, and location characteristics independent to each other) that correlate to the manufacturing process parameters and to the manufacturing process coordinate system established from the manufacturing datum system are used.
This document describes the concept of decomposition of the macro-geometrical part of the GPS specification. It does not cover the micro-geometry, i.e. surface texture.
The objective of the decomposition presented in this document is to define correction values for manufacturing control or to perform a statistical analysis of the process.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5458:2018(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)
SIST EN ISO 5458:2018

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zones are grouped together with location or orientation constraints, through the use of the CZ, CZR or SIM modifiers.
This document does not cover the use of the pattern specifications when the least and maximum material requirement is applied (see ISO 2692).
This document does not cover the establishment of common datum (see ISO 5459) based on pattern features.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17450-4:2018(Main)
Geometrical product specifications (GPS) - Basic concepts - Part 4: Geometrical characteristics for quantifying GPS deviations (ISO 17450-4:2017)
SIST EN ISO 17450-4:2018

ISO 17450-4:2017 specifies general rules for quantifying GPS deviations for individual GPS characteristics.
NOTE       GPS deviations can be local or global. A GPS characteristic defined from local GPS deviations is a parameter that transforms the set of local deviations into a global characteristic using a quantifying function (for more details, see Table 1).

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14253-1:2017(Main)
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for verifying conformity or nonconformity with specifications (ISO 14253-1:2017)
SIST EN ISO 14253-1:2018

ISO 14253-1:2017 establishes the rules for verifying the conformity or nonconformity with a given tolerance for a characteristic of a workpiece (or a population of workpieces) or with a given maximum permissible errors for a metrological characteristic of a measuring equipment, including when the measured value falls close to the specification limits, taking measurement uncertainty into account.
ISO 14253-1:2017 applies to specifications defined in general GPS standards (see ISO 14638), i.e. standards prepared by ISO/TC 213, including:
-      workpiece specifications and population specifications (usually given as an upper specification limit or a lower specification limit or both);
-      measuring equipment specifications (usually given as maximum permissible errors).
ISO 14253-1:2017 only applies for characteristics and maximum permissible errors expressed as quantity values.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 25178-71:2017(Main)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 71: Software measurement standards (ISO 25178-1:2017)
SIST EN ISO 25178-71:2017

ISO 25178-71:2017 defines Type S1 and Type S2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type S1 software measurement standards for the calibration of instruments for the measurement of surface texture by the areal method as defined in the areal surface texture chain of standards, chain link G.
NOTE       Throughout ISO 25178-71:2017, the term "softgauge" is used as a substitute for "software measurement standard Type S1".

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 25178-72:2017(Main)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 72: XML file format x3p (ISO 25178-72:2017)
SIST EN ISO 25178-72:2017

ISO 25178-72:2017 defines the XML file format x3p for storage and exchange of topography and profile data.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day