Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2016)

ISO 3040:2016 specifies graphical indication applicable to a cone (right-angle circular cones) to define its dimensioning or to specify its tolerancing.
For the purposes of this International Standard, the term "cone" relates to right-angle circular cones only (any intersection by a plane perpendicular to the axis of the nominal cone is a circle).
NOTE 1       For simplicity, only truncated cones have been represented in this International Standard. However, this International Standard can be applied to any type of cone within its scope.
NOTE 2       This International Standard is not intended to prevent the use of other methods of dimensioning and tolerancing.

Geometrische Produktspezifikation (GPS) - Bemaßung und Tolerierung - Kegel (ISO 3040:2016)

Diese Internationale Norm spezifiziert die Zeichnungseintragungen für einen Kegel (rechtwinklige kreisförmige Kegel) zur Definition seiner Bemaßung oder Spezifikation seiner Tolerierung.
Für den Zweck dieser Internationalen Norm bezieht sich der Begriff „Kegel“ nur auf rechtwinklige kreisförmige Kegel (jeder Schnittpunkt durch eine Ebene senkrecht zur Achse des Nennkegels ist ein Kreis).
ANMERKUNG 1   Zur Vereinfachung wurden nur abgeschnittene Kegel in dieser Internationalen Norm dargestellt. Diese Internationale Norm kann allerdings innerhalb ihres Anwendungsbereiches auf beliebige Kegeltypen angewendet werden.
ANMERKUNG 2   Es ist nicht die Absicht dieser Internationalen Norm, die Verwendung anderer Methoden der Bemaßung und Toleranzfestlegung auszuschließen.

Spécification géométrique des produits (GPS) - Cotation et tolérancement - Cônes (ISO 3040:2016)

ISO 3040:2016 spécifie l'indication graphique applicable à un cône (cônes de révolution) pour définir sa cotation ou pour spécifier son tolérancement.
Pour les besoins de la présente Norme internationale, le terme « cône » se rapporte seulement aux cônes de revolution (toute intersection par un plan perpendiculaire à l'axe du cône nominal est un cercle).
NOTE 1       Dans la présente Norme internationale, seuls les troncs de cônes ont été représentés, ceci à des fins de simplification. Cependant la présente Norme internationale peut s'appliquer à tous types de cônes, dans le cadre de son domaine d'application.
NOTE 2       II n'est pas dans l'intention de la présente Norme internationale d'empêcher l'emploi d'autres méthodes de cotation et de tolérancement.

Specifikacija geometrijskih veličin izdelka (GPS) - Dimenzioniranje in toleriranje - Konusi (ISO 3040:2016)

Ta mednarodni standard določa grafične oznake za konuse (pravokotne krožne konuse), s katerimi se določi dimenzioniranje ali toleriranje.
V tem mednarodnem standardu se izraz »konus« nanaša samo na pravokotne krožne konuse (vsak presek z ravnino pravokotno na os nominalnega konusa je krog).
OPOMBA 1: Zaradi poenostavitve so v tem mednarodnem standardu predstavljeni samo skrajšani konusi, vendar se lahko standard uporablja za katero koli vrsto konusa, ki spada v njegovo področje uporabe.
OPOMBA 2: Ta mednarodni standard ne preprečuje uporabe drugih načinov dimenzioniranja in toleriranja.

General Information

Status
Published
Publication Date
03-May-2016
Withdrawal Date
29-Nov-2016
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
04-May-2016
Completion Date
04-May-2016

Relations

Buy Standard

Standard
EN ISO 3040:2016
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3040:2016
01-julij-2016
1DGRPHãþD
SIST EN ISO 3040:2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 'LPHQ]LRQLUDQMHLQWROHULUDQMH
.RQXVL ,62
Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO
3040:2016)
Geometrische Produktspezifikation (GPS) - Maßeintragung und Toleranzfestlegung -
Kegel (ISO 3040:2016)
Spécification géométrique des produits (GPS) - Cotation et tolérancement - Cônes (ISO
3040:2016)
Ta slovenski standard je istoveten z: EN ISO 3040:2016
ICS:
01.100.20 Konstrukcijske risbe Mechanical engineering
drawings
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
SIST EN ISO 3040:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3040:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 3040:2016


EN ISO 3040
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2016
EUROPÄISCHE NORM
ICS 17.040.30 Supersedes EN ISO 3040:2012
English Version

Geometrical product specifications (GPS) - Dimensioning
and tolerancing - Cones (ISO 3040:2016)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Cotation et tolérancement - Cônes (ISO 3040:2016) Maßeintragung und Toleranzfestlegung - Kegel (ISO
3040:2016)
This European Standard was approved by CEN on 1 November 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3040:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3040:2016
EN ISO 3040:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3040:2016
EN ISO 3040:2016 (E)
European foreword
This document (EN ISO 3040:2016) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2016, and conflicting national standards
shall be withdrawn at the latest by November 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 3040:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3040:2016 has been approved by CEN as EN ISO 3040:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3040:2016

---------------------- Pa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.