EN ISO 14373:2024

Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2024)

This document specifies requirements for resistance spot welding in the fabrication of assemblies of uncoated and metallic-coated or weldable non-metallic-coated low-carbon steel, comprising two or three sheets of metal, where the maximum single-sheet thickness of components to be welded is within the range 0,4 mm to 3,0 mm.
This document is applicable to welding of sheets of the same or unequal thickness, where the thickness ratio is less than or equal to 3:1.
Welding with the following types of equipment is within the scope of this document:
a)       pedestal welding equipment;
b)       portable welding guns;
c)        automatic welding equipment where the components are fed by robots or automatic feeding equipment;
d)       multi-spot-welding machines;
e)       robotic welding machines.

Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen mit oder ohne metallischem Überzug (ISO 14373:2024)

Dieses Dokument legt Anforderungen an das Widerstandspunktschweißen bei der Fertigung von Bauteilen aus niedriglegiertem Stahl ohne Überzug und mit metallischem Überzug oder schweißbarem nichtmetallischen Überzug fest, die aus zwei oder drei Metallblechen bestehen, wobei die größte Dicke eines Einzelbleches der zu schweißenden Bauteile im Bereich von 0,4 mm bis 3,0 mm liegt.
Dieses Dokument ist anwendbar für das Schweißen von Blechen gleicher oder ungleicher Dicke mit einem Dickenverhältnis von nicht mehr als 3 : 1.
Die folgenden Arten von Schweißeinrichtungen liegen im Anwendungsbereich dieses Dokumentes:
a)   Ständerschweißmaschinen;
b)   tragbare Schweißzangen;
c)   automatische Schweißeinrichtungen, bei denen die Bauteile durch Roboter oder automatische Zuführungen zugeführt werden;
d)   Vielpunkt-Schweißmaschinen;
e)   Roboter-Schweißmaschinen.

Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et non revêtus (ISO 14373:2024)

Le présent document spécifie les exigences relatives au soudage par résistance par points pour la fabrication d'assemblages en acier à bas carbone non revêtu et à revêtement métallique ou à revêtement non métallique soudable, avec deux ou trois épaisseurs de métal, l'épaisseur maximale de chaque tôle constituant les pièces à souder étant comprise entre 0,4 mm et 3,0 mm.
Le présent document s'applique au soudage de tôles présentant une épaisseur similaire ou inégale, et dont le rapport entre les épaisseurs est inférieur ou égal à 3:1.
Le présent document couvre le soudage réalisé avec les types de matériels suivants:
a)       machine de soudage avec commande au pied;
b)       pinces de soudage portables;
c)        matériel de soudage automatique avec lequel les composants sont mis en place par des robots ou des appareils d'alimentation automatique;
d)       machines à souder multi-points;
e)       robots de soudage.

Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih maloogljičnih jekel (ISO 14373:2024)

General Information

• Status: Published
• Publication Date: 30-Jan-2024
• ICS: 25.160.10 - Welding processes
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121 - Welding
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 31-Jan-2024
• Completion Date: 31-Jan-2024
• Ref Project: SIST EN ISO 14373:2024 - Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2024)

Relations

• Replaces: EN ISO 14373:2015 - Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015)
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 14373:2023
01-maj-2023
Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih
maloogljičnih jekel (ISO/DIS 14373:2023)
Resistance welding - Procedure for spot welding of uncoated and coated low carbon
steels (ISO/DIS 14373:2023)
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen
mit oder ohne metallischem Überzug (ISO/DIS 14373:2023)
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas
carbone revêtus et non revêtus (ISO/DIS 14373:2023)
Ta slovenski standard je istoveten z: prEN ISO 14373
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
oSIST prEN ISO 14373:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 14373:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 14373:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14373
ISO/TC 44/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-03-16 2023-06-08
Resistance welding — Procedure for spot welding of
uncoated and coated low carbon steels
Soudage par résistance — Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et
non revêtus
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14373:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 14373:2023
ISO/DIS 14373:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14373
ISO/TC 44/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:

Resistance welding — Procedure for spot welding of
uncoated and coated low carbon steels
Soudage par résistance — Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et
non revêtus
ICS: 25.160.10
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 14373:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 14373:2023
ISO/DIS 14373:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references .
...