Gas-fired endothermic engine driven heat pumps - Part 5: Calculation of seasonal performances in heating and cooling mode

1.1   Scope of FprEN 16905 series
This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as “GEHP appliance”.
This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions.
This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437.
This European Standard only applies to appliances having:
a)   gas fired endothermic engines under the control of fully automatic control systems;
b)   closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated;
c)   where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the:
1)   heating water circuit (if installed) does not exceed 6 bar,
2)   domestic hot water circuit (if installed) does not exceed 10 bar.
This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery.
The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard.
Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard.
The above appliances can have one or more primary or secondary functions.
This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration.
In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package.
NOTE   All the symbols given in this text are used regardless of the language used.
1.2   Scope of FprEN 16905 5
This part of the FprEN 16905 series specifies the calculation of seasonal performance factor for gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.

Gasbefeuerte endothermische Motor-Wärmepumpen - Teil 5: Berechnung der saisonalen Effizienzkennzahlen im Heiz- und Kühlmodus

1.1   Anwendungsbereich der Normenreihe EN 16905
Diese Europäische Norm legt die Anforderungen, Prüfverfahren und Prüfbedingungen für die Bewertung und Leistungsberechnung von Luftkonditionierern und Wärmepumpen mit gasbefeuerten endothermischen motorgetriebenen Verdichtern fest, die entweder Luft, Wasser oder Sole als Wärmeübertragungsmedium verwenden und zur Raumbeheizung, Raumkühlung und Kälteerzeugung dienen, nachfolgend als "GEHP-Gerät" bezeichnet.
Diese Europäische Norm gilt ausschließlich für Geräte mit einer maximalen Wärmebelastung von 70 kW (bezogen auf den Heizwert [NCV; en: net calorific value]) bei Norm-Nennbedingungen.
Diese Europäische Norm gilt entsprechend der EN 437 ausschließlich für Geräte der Kategorien I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P und II2Er3P.
Diese Europäische Norm gilt ausschließlich für Geräte mit:
a)   endothermischen Gasmotoren, die durch vollständig automatisierte Regelungen gesteuert werden;
b)   geschlossenen Kühlkreislaufsystemen, in denen das Kühlmittel nicht direkt mit der zu kühlenden oder zu erwärmenden Flüssigkeit in Berührung kommt;
c)   einer Temperatur des Wärmeübertragungsmediums im Heizsystem (Heizungswasserkreislauf), die im Normalbetrieb 105 °C nicht überschreitet;
d)   einem höchsten Betriebsdruck im:
1)   Heizungswasserkreislauf (falls installiert), der 6 bar nicht überschreitet;
2)   Trinkwasserkreislauf (falls installiert), der 10 bar nicht überschreitet.
Diese Europäische Norm gilt ausschließlich für Geräte, die zur Raumheizung oder -kühlung oder zur Kälteerzeugung mit oder ohne Wärmerückgewinnung angewendet werden.
In dieser Europäischen Norm werden keine Geräte behandelt, deren Kondensator mit Luft oder durch Verdampfung von zusätzlichem Wasser auf der Außenseite gekühlt wird.
In dieser Europäischen Norm werden Kompaktsysteme, Single-Split- und Multi-Split-Systeme behandelt. Auch Einkanal- und Zweikanal-Einheiten werden in der vorliegenden Europäischen Norm behandelt.
Die vorstehend aufgeführten Geräte können eine oder mehrere Primär- oder Sekundärfunktion(en) haben.
Diese Europäische Norm gilt für Geräte, die einer Typprüfung zu unterziehen sind. Anforderungen an nicht typgeprüfte Geräte wären ein Thema für weitere Überlegungen.
Bei (aus mehreren Teilen bestehenden) Kompaktsystemen gilt die vorliegende Europäische Norm nur, wenn sie als vollständige Baugruppe ausgelegt und geliefert werden.
ANMERKUNG   Sämtliche in diesem Text angegebenen Symbole werden unabhängig von der jeweilig verwendeten Sprache angewendet.
1.2   Anwendungsbereich der EN 16905-5
Dieser Teil der Normenreihe EN 16905 legt Berechnungsverfahren für den saisonalen Leistungsfaktor von gasbefeuerten endothermischen Motor-Wärmepumpen fest, die für den Heiz- und/oder Kühlbetrieb, einschließlich der Motor-Wärmerückgewinnung, vorgesehen sind.

Pompes à chaleur à moteur endothermique alimenté au gaz -Partie 5 : Calcul des performances saisonnières en modes chauffage et refroidissement

1.1   Domaine d'application de la série EN 16905
La présente Norme européenne spécifie les exigences, les méthodes d'essai et les conditions d'essai applicables aux calculs des caractéristiques et des performances des climatiseurs et pompes à chaleur utilisant de l'air, de l'eau ou de l'eau glycolée comme fluide caloporteur, munis de compresseurs à moteur endothermique alimenté au gaz, et destinés à des applications de chauffage, de refroidissement et de réfrigération de locaux (ci-après désignés par l'appellation « appareils GEHP »).
Cette norme s'applique uniquement aux appareils dont le débit calorifique maximal (dérivé du pouvoir calorifique inférieur) ne dépasse pas 70 kW dans les conditions de performance nominale.
Elle se limite également aux appareils classés dans les catégories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P et II2Er3P de l'EN 437.
Cette norme ne s'applique qu'aux appareils :
a)   équipés de moteurs endothermiques alimentés au gaz régulés par des systèmes de régulation entièrement automatisés ;
b)   comportant des circuits fermés de réfrigérant dans lesquels le réfrigérant n'entre pas en contact direct avec le fluide à refroidir ou à chauffer ;
c)   dans lesquels la température du fluide caloporteur du système de chauffage (circuit d'eau de chauffage) ne dépasse pas 105 °C dans les conditions normales de fonctionnement ;
d)   dans lesquels la pression maximale de fonctionnement
1)   ne dépasse pas 6 bar dans le circuit d'eau de chauffage (le cas échéant) et
2)   ne dépasse pas 10 bar dans le circuit d'eau chaude sanitaire (le cas échéant).
Cette norme s'applique aux appareils utilisés uniquement pour le chauffage de locaux, le refroidissement de locaux ou la réfrigération, avec ou sans récupération de chaleur.
Elle ne couvre pas les appareils dont le condenseur est refroidi par air et par évaporation de l'eau d'un circuit supplémentaire externe.
Cette norme couvre les systèmes autonomes, mono-split et multi-split. Les installations à simple conduit et à double conduit entrent également dans son domaine d'application.
Les appareils ci-dessus peuvent assurer une ou plusieurs fonctions principales ou secondaires.
Cette norme s'applique aux appareils destinés à être soumis à des essais de type. Les exigences relatives aux appareils non soumis à des essais de type pourraient appeler des considérations supplémentaires.
Dans le cas des appareils autonomes (constitués de plusieurs éléments), la norme ne s'applique qu'aux appareils conçus et fournis sous forme d'ensemble complet.
NOTE   Il faut employer tous les symboles spécifiés dans le présent document, quelle que soit la langue utilisée.
1.2   Domaine d'application de la présente EN 16905-5
La présente partie de la série EN 16905 décrit le calcul du facteur de performance saisonnière pour le mode chauffage et/ou refroidissement, y compris la récupération de chaleur du moteur.

Toplotna črpalka s plinsko gnanim motorjem z notranjim zgorevanjem - 5. del: Izračun sezonske zmogljivosti za ogrevanje in hlajenje

Ta evropski standard določa zahteve, preskusne metode in preskusne pogoje za ocenjevanje in izračun zmogljivosti klimatskih naprav in toplotnih črpalk, ki uporabljajo zrak, vodo ali slanico kot medij za prenos toplote, s kompresorji s plinsko gnanim motorjem z notranjim zgorevanjem, kadar se uporabljajo za segrevanje, ohlajanje in hlajenje, v nadaljevanju »naprava GEHP«.
Ta evropski standard se uporablja samo za naprave z največjo grelno močjo (na podlagi neto kalorične vrednosti), ki ne presega 70 kW pri standardnih pogojih za določanje moči.
Ta evropski standard se uporablja samo za naprave iz kategorij I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P in II2Er3P v skladu s standardom EN 437.
Ta evropski standard se uporablja samo za naprave:
– s plinsko gnanimi motorji z notranjim zgorevanjem, ki jih nadzirajo povsem samodejni krmilni sistemi;
– s hladilnimi tokokrogi z zaprtim sistemom, pri katerih hladilno sredstvo ne pride v neposreden stik s tekočino, ki se ohlaja ali segreva;
– pri katerih temperatura tekočine za prenos toplote ogrevalnega sistema (ogrevalno vodovodno omrežje) pri običajnem delovanju ne presega 105 °C;
– pri katerih najvišji obratovalni tlak v:
– ogrevalnem vodovodnem omrežju (če je nameščeno) ne presega 6 barov;
– gospodinjskem ogrevalnem vodovodnem omrežju (če je nameščeno) ne presega 10 barov.
Ta evropski standard se uporablja za naprave samo, če se uporablja za segrevanje, ohlajanje ali hlajenje prostora z rekuperacijo toplote ali brez nje.
Ta evropski standard ne zajema naprav, katerih kondenzator se hladi z zrakom in izhlapevanjem zunanje dodatne vode.
Ta evropski standard zajema pakirane enote in sisteme z enim ali več razcepi. Ta evropski standard zajema enote z enojnim in dvojnim vodom.
Zgornje naprave imajo lahko eno ali več primarnih ali sekundarnih funkcij.
Ta evropski standard se uporablja za vse naprave, za katere se izvaja tipski preskus. Zahteve za naprave, za katere se ne izvaja tipski preskus, bi bilo treba dodatno proučiti.
Pri pakiranih enotah (sestavljenih iz več kosov) se ta evropski standard uporablja samo za tiste, ki so projektirane in dostavljene kot celoten paket.
OPOMBA Vsi simboli v tem besedilu se uporabljajo ne glede na uporabljeni jezik.

General Information

Status
Withdrawn
Publication Date
07-Mar-2017
Withdrawal Date
20-Dec-2022
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Dec-2022

Relations

Buy Standard

Standard
EN 16905-5:2018
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 16905-5:2015
English language
52 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gasbefeuerte endothermische Motor-Wärmepumpen - Teil 5: Berechnung der saisonalen Effizienzkennzahlen im Heiz- und KühlmodusPompes à chaleur à moteur endothermique alimenté au gaz -Partie 5 : Calcul des performances saisonnières en modes chauffage et refroidissementGas-fired endothermic engine driven heat pumps - Part 5: Calculation of seasonal performances in heating and cooling mode27.080Heat pumpsICS:Ta slovenski standard je istoveten z:EN 16905-5:2017SIST EN 16905-5:2018en,fr,de01-januar-2018SIST EN 16905-5:2018SLOVENSKI
STANDARD



SIST EN 16905-5:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16905-5
March
t r s y ICS
t yä r z r English Version
Gasæfired endothermic engine driven heat pumps æ Part
wã Calculation of seasonal performances in heating and cooling mode Pompes à chaleur à moteur endothermique alimenté au gaz æPartie
w ã Calcul des performances saisonnières en modes chauffage et refroidissement
Gasbefeuerte endothermische MotoræWärmepumpen æ Teil
wã Berechnung der saisonalen Effizienzkennzahlen im Heizæ und Kühlmodus This European Standard was approved by CEN on
{ January
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x { r wæ wã t r s y ESIST EN 16905-5:2018



EN 16905-5:2017 (E) 2 Contents Page European foreword . 4 1 Scope . 5 1.1 Scope of EN 16905 series . 5 1.2 Scope of EN 16905-5 . 5 2 Normative references . 6 3 Terms and definitions . 6 4 Part load conditions in cooling mode . 6 4.1 General . 6 4.2 Air-to-air units . 6 4.3 Water-to-air and brine to air units . 6 4.4 Air-to-water units . 7 4.5 Water-to-water and brine-to-water units . 8 5 Part load conditions in heating mode . 9 5.1 General . 9 5.2 Air-to-air units . 10 5.3 Water-to-air units and brine to air units .
...

SLOVENSKI STANDARD
oSIST prEN 16905-5:2015
01-november-2015
3OLQVNHWRSORWQHþUSDONHHQGRWHUPQHJDPRWRUMDGHO,]UDþXQVH]RQVNH
]PRJOMLYRVWL]DRJUHYDQMHLQKODMHQMH
Gas-fired endothermic engine heat pumps - Part 5: Calculation of seasonal
performances in heating and Cooling mode
Gasbefeuerte endothermische Motor-Wärmepumpen - Teil 5: Berechnung der
saisonalen Effizienzkennzahlen im Heiz- und Kühlmodus
Pompes à chaleur à moteur endothermique alimenté au gaz -Partie 5 : Calcul des
performances saisonnières en modes chauffage et refroidissement
Ta slovenski standard je istoveten z: prEN 16905-5
ICS:
27.080 7RSORWQHþUSDONH Heat pumps
oSIST prEN 16905-5:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16905-5:2015

---------------------- Page: 2 ----------------------
oSIST prEN 16905-5:2015

EUROPEAN STANDARD
DRAFT
prEN 16905-5
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2015
ICS
English Version
Gas-fired endothermic engine heat pumps - Part 5: Calculation
of seasonal performances in heating and Cooling mode

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 299.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16905-5:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 16905-5:2015
prEN 16905-5:2015 (E)
Contents Page
Foreword .4
1 Scope .5
1.1 Scope of prEN 16905 .5
1.2 Scope of prEN 16905-5 .5
2 Normative references .6
3 Terms and definitions .6
4 Part load conditions in cooling mode.6
4.1 General .6
4.2 Air-to-air units .6
4.3 Water-to-air and brine to air units .6
4.4 Air-to-water units .7
4.5 Water-to-water and brine-to-water units.8
5 Part load conditions in heating mode.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.