EN ISO 17249:2013
(Main)Safety footwear with resistance to chain saw cutting (ISO 17249:2013)
Safety footwear with resistance to chain saw cutting (ISO 17249:2013)
ISO 17249:2013 specifies requirements for safety footwear with resistance to chain saw cutting.
Sicherheitsschuhe mit Schutzwirkung gegen Kettensägenschnitte (ISO 17249:2013)
Diese Internationale Norm legt Anforderungen an Sicherheitsschuhe mit Schutzwirkung gegen
Kettensägenschnitte fest.
Chaussures de sécurité résistantes aux coupures de scie à chaîne (ISO 17249:2013)
L'ISO 17249:2013 spécifie les exigences des chaussures de sécurité résistantes aux coupures de scie à chaîne.
Varovalna obutev, odporna proti urezu z verižno žago (ISO 17249:2013)
Ta mednarodni standard določa zahteve za varovalno obutev, odporno proti urezu z verižno žago.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 17249:2014
01-februar-2014
1DGRPHãþD
SIST EN ISO 17249:2005
SIST EN ISO 17249:2005/A1:2007
Varovalna obutev, odporna proti urezu z verižno žago (ISO 17249:2013)
Safety footwear with resistance to chain saw cutting (ISO 17249:2013)
Sicherheitsschuhe mit Schutzwirkung gegen Kettensägenschnitte (ISO 17249:2013)
Chaussures de sécurité résistantes aux coupures de scie à chaîne (ISO 17249:2013)
Ta slovenski standard je istoveten z: EN ISO 17249:2013
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
SIST EN ISO 17249:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 17249:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 17249:2014
EUROPEAN STANDARD
EN ISO 17249
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2013
ICS 13.340.50 Supersedes EN ISO 17249:2004
English Version
Safety footwear with resistance to chain saw cutting (ISO
17249:2013)
Chaussures de sécurité résistantes aux coupures de scie à Sicherheitsschuhe mit Schutzwirkung gegen
chaîne (ISO 17249:2013) Kettensägenschnitte (ISO 17249:2013)
This European Standard was approved by CEN on 28 September 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17249:2013 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 17249:2014
EN ISO 17249:2013 (E)
Contents Page
Foreword .3
Annex ZA (informative) Clauses of this European Standard addressing essential requirements or
other provisions of EU directives .4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 17249:2014
EN ISO 17249:2013 (E)
Foreword
This document (EN ISO 17249:2013) has been prepared by Technical Committee ISO/TC 94 "Personal safety
- Protective clothing and equipment" in collaboration with Technical Committee CEN/TC 161 “Foot and leg
protectors” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the
latest by November 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17249:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17249:2013 has b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.