iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10028-3:2003

(Main)

Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized

Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized

This EN 10028-3 specifies requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Table 1. NOTE Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with EURONORM 103. The requirements and definitions of EN 10028-1 also apply.

Flacherzeugnisse aus Druckbehälterstählen - Teil 3: Schweißgeeignete Feinkornbaustähle, normalgeglüht

Die Europäische Norm EN 10028-3 enthält die Anforderungen an Flacherzeugnisse für Druckbehälter aus den schweißgeeigneten Feinkornbaustählen, die in Tabelle 1 festgelegt sind.
ANMERKUNG   Unter Feinkornbaustählen werden Stähle verstanden, die bei Prüfung nach EURONORM 103 eine Ferritkorngröße von 6 oder feiner aufweisen.
Zusätzlich gelten die Anforderungen und Begriffe in EN 10028-1.

Produits plats en aciers pour appareils à pression - Partie 3: Aciers soudables à grains fins, normalisés

La présente partie 3 de l'EN 10028 spécifie les prescriptions relatives aux produits plats pour appareils à pression en aciers à grains fins aptes au soudage telles qu'indiquées dans le Tableau 1. NOTE Par "aciers à grains fins", on entend les aciers ayant une grosseur de grain ferritique <= 6, déterminée conformément à l'EURONORM 103. Les prescriptions et définitions de l'EN 10028-1 s'appliquent également.

Ploščati jekleni izdelki za tlačne posode – 3. del: Variva drobnozrnata jekla, normalizirana

General Information

Status
Withdrawn
Publication Date
17-Jun-2003
Withdrawal Date
16-Jun-2009
ICS
77.140.30 - Steels for pressure purposes
77.140.50 - Flat steel products and semi-products
Technical Committee
ECISS/TC 107 - Steels for pressure purposes
Drafting Committee
ECISS/TC 22 - Steels for pressure purposes - Qualities
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
17-Jun-2009
Completion Date
17-Jun-2009
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
M/BC/CEN/89/10 - ECISS - 3rd programme
Ref Project
SIST EN 10028-3:2003 - Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized

Relations

Replaces
EN 10028-3:1992 - Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
Effective Date
22-Dec-2008
Replaced By
EN 10028-3:2009 - Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
Effective Date
20-Jun-2009

Buy Standard

EN 10028-3:2003EN 10028-3:2003
PreviousNext
Standard
EN 10028-3:2003
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalizedQRUPDOL]LUDQDProduits plats en aciers pour appareils a pression - Partie 3: Aciers soudables a grains fins, normalisésFlacherzeugnisse aus Druckbehälterstählen - Teil 3: Schweißgeeignete Feinkornbaustähle, normalgeglühtTa slovenski standard je istoveten z:EN 10028-3:2003SIST EN 10028-3:2003en77.140.5077.140.30ICS:SIST EN 10028-3:19971DGRPHãþDSLOVENSKI
STANDARDSIST EN 10028-3:200301-november-2003







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-3June 2003ICS 77.140.30; 77.140.50Supersedes EN 10028-3:1992English versionFlat products made of steels for pressure purposes - Part 3:Weldable fine grain steels, normalizedProduits plats en aciers pour appareils à pression - Partie3: Aciers soudables à grains fins, normalisésFlacherzeugnisse aus Druckbehälterstählen - Teil 3:Schweißgeeignete Feinkornbaustähle, normalgeglühtThis European Standard was approved by CEN on 20 January 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-3:2003 E



EN 10028-3:2003 (E)2ContentsPageForeword.31Scope.42Normative references.43Terms and definitions.44Dimensions and tolerances on dimensions.45Calculation of mass.46Classification and designation.46.1Classification.46.2Designation.57Information to be supplied by the purchaser.57.1Mandatory information.57.2Options.57.3Example for ordering.58Requirements.58.1Steelmaking process.58.2Delivery condition.68.3Chemical composition.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10028-4:2017(Main)
Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
SIST EN 10028-4:2017

This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-3:2017(Main)
Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
SIST EN 10028-3:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Table 1.
NOTE 1   Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with EN ISO 643.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE 2   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-2:2017(Main)
Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
SIST EN 10028-2:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable non-alloy and alloy steels with elevated temperature properties as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and this Part 2 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-5:2017(Main)
Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
SIST EN 10028-5:2017

This European Standard specifies the requirements for flat products for pressure equipment made of thermomechanically rolled steels as specified in Table 1.
The steels are not suitable for hot forming.
NOTE 1   At the time of publication of this European Standard, no sufficient data for the standardization of the elevated temperature properties of these steels was available.
If their use at such temperatures is intended the conditions for this should be specially agreed between the interested parties.
The requirements of EN 10028 1:2017 also apply.
NOTE 2   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-6:2017(Main)
Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered
SIST EN 10028-6:2017

This European Standard specifies the requirements for flat products for pressure equipment made of quenched and tempered steels as specified in Table 1.
The requirements in FprEN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-1:2017(Main)
Flat products made of steels for pressure purposes - Part 1: General requirements
SIST EN 10028-1:2017

This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-7:2016(Main)
Flat products made of steels for pressure purposes - Part 7: Stainless steels
SIST EN 10028-7:2016

This European Standard specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses as indicated in Tables 7 to 10.
The requirements of EN 10028-1:2007+A1:2009 also apply.
NOTE 1   The steel grades covered by this European Standard have been selected from EN 10088-1.
NOTE 2   Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and Part 7) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-1:2017(Main)
Flat products made of steels for pressure purposes - Part 1: General requirements
SIST EN 10028-1:2017

This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-2:2017(Main)
Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
SIST EN 10028-2:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable non-alloy and alloy steels with elevated temperature properties as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and this Part 2 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-3:2017(Main)
Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
SIST EN 10028-3:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Table 1.
NOTE 1   Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with EN ISO 643.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE 2   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day