EN 13445-3:2014/A7:2019

Unfired pressure vessels - Part 3: Design

This Part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1:2009 and constructed of steels in accordance with EN 13445-2:2009. EN 13445-5:2009, Annex C specifies requirements for the design of access and inspection openings, closing mechanisms and special locking elements. NOTE This Part applies to design of vessels before putting into service. It may be used for in service calculation or analysis subject to appropriate adjustment.

Unbefeuerte Druckbehälter - Teil 3: Konstruktion

Dieser Teil 3 der Europäischen Norm legt die Anforderungen an die Konstruktion von unbefeuerten Druckbehältern
nach EN 13445-1:2014 und hergestellt aus Stählen nach EN 13445-2:2014 fest.
EN 13445-5:2014 gibt im Anhang C Bedingungen für die Konstruktion von Zugangs- und Besichtigungsöffnungen,
von Verschlüssen und besonderen Verschlusselementen.
ANMERKUNG Dieser Teil gilt für Konstruktion und Berechnung von Behältern vor der Inbetriebnahme. Er kann auch, mit
entsprechenden Anpassungen, für Berechnungen oder analytische Nachweise im Betrieb verwendet werden.

Récipients sous pression non soumis à la flamme - Partie 3 : Conception

Cette partie de la présente norme européenne spécifie les exigences relatives à la conception des récipients sous
pression non soumis à la flamme couverts par l’EN 13445-1:2014 et construits en aciers conformes à
l’EN 13445-2:2014.
L’Annexe C de l’EN 13445-5:2014 spécifie les exigences relatives à la conception des ouvertures d’accès et
d’inspection, des mécanismes de fermeture et des éléments de verrouillage spéciaux.
NOTE Cette partie s'applique à la conception des récipients avant mise en service. Elle peut être utilisée pour les calculs
ou l'analyse en service sous réserve d'apporter les ajustements appropriés.

Neogrevane (nekurjene) tlačne posode - 3. del: Konstruiranje - Dopolnilo A7

General Information

• Status: Withdrawn
• Publication Date: 02-Apr-2019
• Withdrawal Date: 11-May-2021
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: CEN/TC 54 - Unfired pressure vessels
• Drafting Committee: CEN/TC 54/WG 59 - Creep
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 12-May-2021
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 13445-3:2014/A7:2019 - Unfired pressure vessels - Part 3: Design

Relations

• Replaced By: EN 13445-3:2021 - Unfired pressure vessels - Part 3: Design
• Effective Date: 24-Apr-2019
• Amends: EN 13445-3:2014 - Unfired pressure vessels - Part 3: Design
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13445-3:2014/A7:2019
01-maj-2019
1HRJUHYDQHQHNXUMHQHWODþQHSRVRGHGHO.RQVWUXLUDQMH'RSROQLOR$
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Ta slovenski standard je istoveten z: EN 13445-3:2014/A7:2019
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
SIST EN 13445-3:2014/A7:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13445-3:2014/A7:2019

---------------------- Page: 2 ----------------------

SIST EN 13445-3:2014/A7:2019


EN 13445-3:2014/A7
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2019
EUROPÄISCHE NORM
ICS 23.020.30
English Version

Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Partie 3 : Conception
This amendment A7 modifies the European Standard EN 13445-3:2014; it was approved by CEN on 12 November 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-3:2014/A7:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13445-3:2014/A7:2019
EN 13445-3:2014/A7:2019 (E)
Contents Page
European foreword . 3
1 Modification to Annex R (informative), Coefficients for creep-rupture model equations for
extrapolation of creep-rupture strength . 4

2

---------------------- Page: 4 ----------------------

SIST EN 13445-3:2014/A7:2019
EN 13445-3:2014/A7:2019 (E)
European foreword
This document (EN 13445-3:2014/A7:2019) has been prepared by Technical Committee CEN/TC 54
“Unfired pressure vessels”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2019, and conflicting national standards shall be withdrawn
at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of
EN 13445-3:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 13445-3:2014/A7:2019
EN 13445-3:2014/A7:2019 (E)
1 Modification to Annex R (informative), Coefficients for creep-rupture model
equations for extrapolation of creep-rupture strength
Replace the existing annex with the following one:
“
4
...