Rubber or plastics-coated fabrics - Mechanical test methods under biaxial stress states - Part 1: Tensile stiffness properties

This document describes methods of test using biaxial stress states for the determination of the tensile stiffness properties of biaxially oriented coated fabrics (properties along anisotropic directions, such as the weft and warp yarns for woven based coated fabrics, or along the courses and wales of knitted based coated fabrics).
Other mechanical properties (such as pattern compensation values, shear stiffness, and strength) will be described in other parts.

Mit Kautschuk oder Kunststoff beschichtete Textilien - Mechanische Prüfverfahren unter biaxialen Spannungszuständen - Teil 1: Zugsteifigkeitseigenschaften

In diesem Dokument werden Prüfverfahren unter biaxialen Spannungszuständen zur Bestimmung der Zug¬steifigkeitseigenschaften von biaxial ausgerichteten beschichteten Textilien beschrieben (Eigenschaften in Bezug auf anisotrope Richtungen wie Schuss und Kette bei gewebten beschichteten Textilien oder entlang der Produktionsrichtung und senkrecht dazu bei beschichteten Maschenwaren).
Weitere mechanische Eigenschaften (wie Kompensationswerte, Schubsteifigkeit und Zugfestigkeit) werden in anderen Dokumentteilen beschrieben.

Supports textiles revêtus de caoutchouc ou de plastique - Méthodes d’essais mécaniques sous contraintes biaxiales - Partie 1 : Propriétés de rigidité à la traction

Le présent document décrit des méthodes d’essai sous contraintes biaxiales pour la détermination des propriétés de rigidité à la traction de supports textiles revêtus à orientation biaxiale (propriétés suivant les sens anisotropiques comme les fils de trame et de chaîne pour les supports textiles revêtus tissés, ou suivant les rangées et colonnes de mailles des supports textiles revêtus tricotés).
D’autres propriétés mécaniques (comme les valeurs de compensation du patronage, la rigidité au cisaillement et la résistance) seront décrites dans d’autres parties.

Gumirane ali plastificirane tekstilije - Mehanske preskusne metode pri dvoosnih napetostnih stanjih - 1. del: Lastnosti natezne togosti

Ta dokument opisuje preskusne metode pri dvoosnih napetostnih stanjih za določanje lastnosti
natezne togosti dvoosnih prevlečenih tekstilij (lastnosti poleg anizotropnih smeri), kot so
votkovne in osnovne niti za tkane prevlečene tekstilije ali ob plasteh in valovih pletenih
prevlečenih tekstilij).
Druge mehanske lastnosti (kot so vrednosti kompenzacije vzorca, strižna togost in trdnost) bodo
opisane v drugih delih.

General Information

Status
Published
Publication Date
27-Nov-2018
Withdrawal Date
30-May-2019
Current Stage
9020 - Submission to 2 Year Review Enquiry - Review Enquiry
Start Date
15-Jan-2024
Completion Date
15-Jan-2024

Buy Standard

Standard
EN 17117-1:2019
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17117-1:2017
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17117-1:2019
01-februar-2019
Gumirane ali plastificirane tekstilije - Mehanske preskusne metode pri dvoosnih
napetostnih stanjih - 1. del: Lastnosti natezne togosti
Rubber or plastics-coated fabrics - Mechanical test methods under biaxial stress states –
Part 1: Tensile stiffness properties
Mit Kautschuk oder Kunststoff beschichtete Textilien - Mechanische Prüfverfahren unter
biaxialen Spannungszuständen - Teil 1: Zugsteifigkeitseigenschaften
Supports textiles revêtus de caoutchouc - Méthodes d'essais mécaniques sous
contraintes biaxiales - Partie 22 : Propriétés de rigidité sous traction
Ta slovenski standard je istoveten z: EN 17117-1:2018
ICS:
59.080.40 3RYUãLQVNRSUHYOHþHQH Coated fabrics
WHNVWLOLMH
SIST EN 17117-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 17117-1:2019

---------------------- Page: 2 ----------------------

SIST EN 17117-1:2019


EN 17117-1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2018
EUROPÄISCHE NORM
ICS 59.080.40
English Version

Rubber or plastics-coated fabrics - Mechanical test
methods under biaxial stress states - Part 1: Tensile
stiffness properties
Supports textiles revêtus de caoutchouc ou de Mit Kautschuk oder Kunststoff beschichtete Textilien -
plastique - Méthodes d'essais mécaniques sous Mechanische Prüfverfahren unter biaxialen
contraintes biaxiales - Partie 1 : Propriétés de rigidité à Spannungszuständen - Teil 1:
la traction Zugsteifigkeitseigenschaften
This European Standard was approved by CEN on 4 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17117-1:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 17117-1:2019
EN 17117-1:2018 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 10
5 Apparatus . 10
5.1 Biaxial test equipment . 10
5.2 Measurement of load . 10
5.3 Measurement of strain . 10
6 Sampling and preparation of test specimens .
...

SLOVENSKI STANDARD
oSIST prEN 17117-1:2017
01-maj-2017
Gumirane ali plastificirane tekstilije - Mehanske preskusne metode pri dvoosnih
napetostnih stanjih - 1. del: Lastnosti natezne togosti
Rubber or plastics-coated fabrics - Mechanical test methods under biaxial stress states –
Part 1: Tensile stiffness properties
Mit Kautschuk oder Kunststoff beschichtete Textilien - Mechanische Prüfverfahren unter
biaxialen Spannungszuständen - Teil 1: Zugsteifigkeitseigenschaften
Supports textiles revêtus de caoutchouc - Méthodes d'essais mécaniques sous
contraintes biaxiales - Partie 22 : Propriétés de rigidité sous traction
Ta slovenski standard je istoveten z: prEN 17117-1
ICS:
59.080.40 3RYUãLQVNRSUHYOHþHQH Coated fabrics
WHNVWLOLMH
oSIST prEN 17117-1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17117-1:2017

---------------------- Page: 2 ----------------------
oSIST prEN 17117-1:2017


DRAFT
EUROPEAN STANDARD
prEN-17117-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2017
ICS
English Version

Rubber or plastics-coated fabrics - Mechanical test
methods under biaxial stress states - Part 1: Tensile
stiffness properties
Supports textiles revêtus de caoutchouc - Méthodes Mit Kautschuk oder Kunststoff beschichtete Textilien -
d'essais mécaniques sous contraintes biaxiales - Partie Mechanische Prüfverfahren unter biaxialen
22 : Propriétés de rigidité sous traction Spannungszuständen - Teil 1:
Zugsteifigkeitseigenschaften
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 248.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN-17117-1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17117-1:2017
prEN 17117-1:2017 (E)
D.7 Method F . 34
Annex E (informative) Determination of comparative elastic constants . 35
E.1 Scope and Field of Applications . 35
E.2 Symbols . 35
E.3 Constitutive law used . 35
E.4 Determination procedure . 35
Annex F (informative) Rationale . 36
Bibliography . 37


3

---------------------- Page: 4 -------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.