iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN/TR 17081:2018

(Main)

Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners

Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners

This Technical Report gives provisions for design of ultimate limit states in addition to EN 1992 4 for headed and post-installed fasteners excluding concrete screws, which only transmit static actions to the concrete, when the loads on individual fasteners are determined according to plastic analysis of the joint where only equilibrium conditions but no compatibility conditions are considered. Fatigue, impact and seismic loads are not covered.

Bemessung der Verankerung von Befestigungen in Beton - Traglastverfahren für Befestigungsmittel von Kopfbolzen und Dübel

Conception-calcul des fixations pour utilisation dans le béton - Conception plastique des fixations à boulons à tête et à chevilles de fixation

Projektiranje pritrjevanja za uporabo v betonu - Projektiranje pritrjevanja z veznimi sredstvi z glavo in naknadno vgrajenimi veznimi sredstvi po teoriji plastičnosti

To tehnično poročilo zajema določbe za projektiranje skrajnih mejnih stanj dodatno k standardu EN 1992 4 za vezna sredstva z glavo in naknadno vgrajena vezna sredstva razen betonskih vijakov, ki zgolj prenašajo statična dejanja v beton, kadar so obremenitve posameznih veznih elementov določene v skladu s plastično analizo spoja, kjer so upoštevani samo uravnoteženi pogoji, ne pa tudi pogoji združljivosti. Utrujanje, sunki in seizmične obremenitve niso obravnavani.

General Information

Status
Published
Publication Date
25-Sep-2018
ICS
21.060.01 - Fasteners in general
91.080.40 - Concrete structures
Technical Committee
CEN/TC 250 - Structural Eurocodes
Drafting Committee
CEN/TC 250/SC 2/WG 2 - Design of fastenings for use in concrete
Current Stage
9020 - Submission to 2 Year Review Enquiry - Review Enquiry
Start Date
15-Apr-2024
Completion Date
15-Apr-2024
Ref Project
SIST-TP CEN/TR 17081:2018 - Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners

Buy Standard

TP CEN/TR 17081:2018TP CEN/TR 17081:2018
PreviousNext
Technical report
TP CEN/TR 17081:2018
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TP CEN/TR 17081:2018
01-december-2018
3URMHNWLUDQMHSULWUMHYDQMD]DXSRUDERYEHWRQX3URMHNWLUDQMHSULWUMHYDQMD]YH]QLPL
VUHGVWYL]JODYRLQQDNQDGQRYJUDMHQLPLYH]QLPLVUHGVWYLSRWHRULMLSODVWLþQRVWL
Design of fastenings for use in concrete - Plastic design of fastenings with headed and
post-installed fasteners
Bemessung der Verankerung von Befestigungen in Beton - Traglastverfahren für
Befestigungsmittel von Kopfbolzen und Dübel
Conception-calcul des fixations pour utilisation dans le béton - Conception plastique des
fixations à boulons à tête et à chevilles de fixation
Ta slovenski standard je istoveten z: CEN/TR 17081:2018
ICS:
21.060.01 Vezni elementi na splošno Fasteners in general
91.080.40 Betonske konstrukcije Concrete structures
SIST-TP CEN/TR 17081:2018 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN/TR 17081:2018

---------------------- Page: 2 ----------------------

SIST-TP CEN/TR 17081:2018


CEN/TR 17081
TECHNICAL REPORT

RAPPORT TECHNIQUE

September 2018
TECHNISCHER BERICHT
ICS 21.060.01; 91.080.40
English Version

Design of fastenings for use in concrete - Plastic design of
fastenings with headed and post-installed fasteners
 Bemessung der Verankerung von Befestigungen in
Beton - Traglastverfahren für Befestigungsmittel von
Kopfbolzen und Dübel


This Technical Report was approved by CEN on 9 April 2017. It has been drawn up by the Technical Committee CEN/TC 250.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 17081:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN/TR 17081:2018
CEN/TR 17081:2018 (E)
Contents Page

European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 5
4 Field of application . 5
4.1 General . 5
4.2 Conditions for ductile behaviour . 5
5 Loads on fastenings . 8
5.1 General . 8
5.2 Compression forces . 8
5.3 Location of the compressive force . 8
5.4 Assumption for the tension side of the fastening . 10
5.5 Limitation on location of fasteners in tension . 11
5.6 Distribution of shear forces. 11
6 Design of fastenings.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TR 17080:2018(Main)
Design of fastenings for use in concrete - Anchor channels - Supplementary rules
SIST-TP CEN/TR 17080:2018

EN 1992-4:2018 covers anchor channels located in cracked or uncracked concrete subjected to tensile loads and/or shear loads transverse to the longitudinal channel axis as well as combinations of these loads. Shear loads acting in direction of the longitudinal axis of the channel and combinations of shear loads acting transverse and in direction of the longitudinal axis of the channel, combinations of tensile loads and shear loads acting in direction of the longitudinal axis of the channel and combinations of loads in all three directions are excluded.
This Technical Report provides design rules for anchor channels under static and quasi-static shear loads acting in direction of the longitudinal channel axis and all possible combinations of shear and tension loads acting on the channel as well as design rules for anchor channels with supplementary reinforcement to take up shear loads, additional and alternative to the provisions of EN 1992- 4:2018. All relevant failure modes are considered and will be verified. Fatigue, impact and seismic loads are not covered.
The design rules in this document are only valid for anchor channels with a European Technical Product Specification. The design provisions for shear loads acting in direction of the longitudinal axis of the channel cover the following anchor channels and applications:
-   Anchor channels with 2 or 3 anchors.
-   Anchor channels where the shear load in the longitudinal axis of the channel is transferred to the channel by corresponding locking channel bolts creating mechanical interlock by means of a notch in the channel lips or serrated channel bolts which interlock with serrated lips of the channel (Figure 1).
-   Anchor channels produced from steel with at least two metal anchors rigidly connected to the back of the channel (e.g. by welding, forging or screwing). The anchor channels are placed flush with the concrete surface. A fixture is connected to the anchor channel by channel bolts with nut and washer.
-   Anchor channels close to the edge placed either parallel or transverse to the edge of the concrete member. The design provisions for concrete edge failure do not cover channel orientations inclined to the concrete edge.
The design method for anchor channels loaded in shear in direction of the longitudinal axis of the channel follows closely the existing design model for headed fasteners. For reasons of simplicity modifications specific for anchor channels are used where necessary.
The design provisions for the supplementary reinforcement to take up shear loads in case of anchor channels situated parallel to the edge and loaded in shear transverse to the longitudinal axis apply to anchor channels with unlimited number of anchors.
Examples of anchor channels and channel bolts ensuring mechanical interlock are given in Figure 1.

  • Technical report
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17079:2018(Main)
Design of fastenings for use in concrete - Redundant non-structural systems
SIST-TP CEN/TR 17079:2018

1.1   General
This Technical Report provides design rules for fasteners used to connect statically indeterminate non-structural light weight systems (e.g. suspended ceilings, pipe work, ducting) to concrete members such as walls or floors (see Figure 1)).
The proposed design model may be applied to post-installed mechanical and bonded anchors covered by EN 1992-4:2017, 1.2. Their suitability will be confirmed in a European Technical Product Specification.
The design rules assume the following:
-   under extreme conditions (e.g. large crack width) excessive slip or failure of a fastener might occur;
-   elements or systems are attached with at least three fixing points with one or more fasteners at each fixing point;
-   where more than one fastener is used at a fixing point (MF, see Figure 1), only fasteners of the same type, size and length are used;
-   the attached system is sufficiently stiff to transfer the load at any fixing point to adjacent fixing points without significantly impairing the performance characteristics of the system both at serviceability and ultimate limit states.
(...)
This Technical Report applies to non-structural applications in structures covered by EN 1992-1-1. In applications where special considerations apply, e.g. nuclear power plants or civil defence structures, modifications may be necessary.
This document does not cover the design of the fixture. The design of the fixture will be carried out to comply with the appropriate Standards.
1.2   Type of fasteners
Post-installed fasteners according to EN 1992-4.
1.3   Fastener dimensions and materials
EN 1992-4:2017, 1.3 applies with the following addition: In precast pre-stressed hollow core elements the minimum embedment depth may be reduced to a value to ensure proper functioning if placed in a flange (wall) of minimum thickness of 17 mm. In this case the minimum embedment depth and the admissible position of the fastener in the hollow core slab given in the relevant European Technical Product Specification will be observed (Figure 2).
(...)-
1.4   Fastener loading
Loading on the fastenings will only be quasi static. Fatigue, impact and seismic loads are not covered.
Any axial compression on the fixture will be transmitted to the concrete either without acting on the fastener or via fasteners suitable for resisting compression.
1.5   Concrete strength
EN 1992-4 applies.
1.6   Concrete member loading
EN 1992-4 applies. However, fatigue, impact and seismic loads are not covered.
1.7   Concrete member dimensions
The minimum thickness of members in which fasteners are installed is at least 80 mm unless otherwise specified in the European Technical Product Specification. For precast pre-stressed hollow core elements, the minimum wall thickness is 17 mm.

  • Technical report
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17080:2018(Main)
Design of fastenings for use in concrete - Anchor channels - Supplementary rules
SIST-TP CEN/TR 17080:2018

EN 1992-4:2018 covers anchor channels located in cracked or uncracked concrete subjected to tensile loads and/or shear loads transverse to the longitudinal channel axis as well as combinations of these loads. Shear loads acting in direction of the longitudinal axis of the channel and combinations of shear loads acting transverse and in direction of the longitudinal axis of the channel, combinations of tensile loads and shear loads acting in direction of the longitudinal axis of the channel and combinations of loads in all three directions are excluded.
This Technical Report provides design rules for anchor channels under static and quasi-static shear loads acting in direction of the longitudinal channel axis and all possible combinations of shear and tension loads acting on the channel as well as design rules for anchor channels with supplementary reinforcement to take up shear loads, additional and alternative to the provisions of EN 1992- 4:2018. All relevant failure modes are considered and will be verified. Fatigue, impact and seismic loads are not covered.
The design rules in this document are only valid for anchor channels with a European Technical Product Specification. The design provisions for shear loads acting in direction of the longitudinal axis of the channel cover the following anchor channels and applications:
-   Anchor channels with 2 or 3 anchors.
-   Anchor channels where the shear load in the longitudinal axis of the channel is transferred to the channel by corresponding locking channel bolts creating mechanical interlock by means of a notch in the channel lips or serrated channel bolts which interlock with serrated lips of the channel (Figure 1).
-   Anchor channels produced from steel with at least two metal anchors rigidly connected to the back of the channel (e.g. by welding, forging or screwing). The anchor channels are placed flush with the concrete surface. A fixture is connected to the anchor channel by channel bolts with nut and washer.
-   Anchor channels close to the edge placed either parallel or transverse to the edge of the concrete member. The design provisions for concrete edge failure do not cover channel orientations inclined to the concrete edge.
The design method for anchor channels loaded in shear in direction of the longitudinal axis of the channel follows closely the existing design model for headed fasteners. For reasons of simplicity modifications specific for anchor channels are used where necessary.
The design provisions for the supplementary reinforcement to take up shear loads in case of anchor channels situated parallel to the edge and loaded in shear transverse to the longitudinal axis apply to anchor channels with unlimited number of anchors.
Examples of anchor channels and channel bolts ensuring mechanical interlock are given in Figure 1.

  • Technical report
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17079:2018(Main)
Design of fastenings for use in concrete - Redundant non-structural systems
SIST-TP CEN/TR 17079:2018

1.1   General
This Technical Report provides design rules for fasteners used to connect statically indeterminate non-structural light weight systems (e.g. suspended ceilings, pipe work, ducting) to concrete members such as walls or floors (see Figure 1)).
The proposed design model may be applied to post-installed mechanical and bonded anchors covered by EN 1992-4:2017, 1.2. Their suitability will be confirmed in a European Technical Product Specification.
The design rules assume the following:
-   under extreme conditions (e.g. large crack width) excessive slip or failure of a fastener might occur;
-   elements or systems are attached with at least three fixing points with one or more fasteners at each fixing point;
-   where more than one fastener is used at a fixing point (MF, see Figure 1), only fasteners of the same type, size and length are used;
-   the attached system is sufficiently stiff to transfer the load at any fixing point to adjacent fixing points without significantly impairing the performance characteristics of the system both at serviceability and ultimate limit states.
(...)
This Technical Report applies to non-structural applications in structures covered by EN 1992-1-1. In applications where special considerations apply, e.g. nuclear power plants or civil defence structures, modifications may be necessary.
This document does not cover the design of the fixture. The design of the fixture will be carried out to comply with the appropriate Standards.
1.2   Type of fasteners
Post-installed fasteners according to EN 1992-4.
1.3   Fastener dimensions and materials
EN 1992-4:2017, 1.3 applies with the following addition: In precast pre-stressed hollow core elements the minimum embedment depth may be reduced to a value to ensure proper functioning if placed in a flange (wall) of minimum thickness of 17 mm. In this case the minimum embedment depth and the admissible position of the fastener in the hollow core slab given in the relevant European Technical Product Specification will be observed (Figure 2).
(...)-
1.4   Fastener loading
Loading on the fastenings will only be quasi static. Fatigue, impact and seismic loads are not covered.
Any axial compression on the fixture will be transmitted to the concrete either without acting on the fastener or via fasteners suitable for resisting compression.
1.5   Concrete strength
EN 1992-4 applies.
1.6   Concrete member loading
EN 1992-4 applies. However, fatigue, impact and seismic loads are not covered.
1.7   Concrete member dimensions
The minimum thickness of members in which fasteners are installed is at least 80 mm unless otherwise specified in the European Technical Product Specification. For precast pre-stressed hollow core elements, the minimum wall thickness is 17 mm.

  • Technical report
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5832-1:2024(Main)
Implants for surgery - Metallic materials - Part 1: Wrought stainless steel (ISO 5832-1:2024)
SIST EN ISO 5832-1:2024

This document specifies the characteristics of, and corresponding test methods for, wrought stainless steel for use in the manufacture of surgical implants.
NOTE 1       The mechanical properties of a sample obtained from a finished product made of this alloy can differ from those specified in this document.
NOTE 2       The alloy described in this document corresponds to UNS S31673 in ASTM F138 and ASTM F139.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16451:2024(Main)
Railway applications - Braking - Brake pad holder
SIST EN 16451:2024

This document defines requirements for the brake pad holders with which the heavy rail vehicles and urban rail vehicles are fitted.
This document is applicable to the brake pad holders made from ferrous materials e.g. cast iron, cast steel or forged steel.
This document is not applicable for brake pad holders made of non-ferrous materials.

  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1482-4:2024(Main)
Fertilizers, liming materials and inhibitors - Sampling and sample preparation - Part 4: Sampling for microbial presence
SIST EN 1482-4:2024

This document specifies the method for taking a sample of solid and liquid forms of organic fertilizers, organo-mineral fertilizers and inorganic fertilizers containing more than 1 % by mass of organic carbon, when in packages, containers or in bulk, to test for levels of controlled pathogens present.

  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12368:2024(Main)
Traffic control equipment - Signal heads
kSIST FprEN 12368:2023

This document applies to signal heads with one or more signal lights of the colours red, yellow and/or green signal lights for road traffic with 200 mm and 300 mm roundels and to optical units to be integrated in signal heads to produce the individual signal lights. It defines the product characteristics for the visual, structural, environmental performances and testing of signal heads and optical units for pedestrian and road traffic use, and the rules for the evaluation of the conformity of these products.
This document can be partly or fully applied on a voluntary basis to other signal heads outside of the scope specified above like for instance white optical units or small signal heads with a diameter smaller than 200 mm.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1570-1:2024(Main)
Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landing
kSIST FprEN 1570-1:2022

1.1   This document specifies the safety requirements for lifting tables with the following characteristics:
-   serving no more than 2 fixed landings but able to pass a fixed landing and,
-   having a vertical travel speed of no more than 0,15 m/s, unless safe by position and,
-   for raising or lowering goods (with or without operator(s) and/or authorized person(s)), or;
-   for raising or lowering operator(s) and/or authorized person(s) with or without goods, to positions where they can carry out work from a fixed or movable lifting table that is guided throughout its vertical travel only (see Annex H).
1.2   This document specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards listed in Annex B.
1.3   This document does not apply to the following equipment:
-   lifting tables with a vertical travel speed exceeding 0,15 m/s, unless safe by position;
-   lifting tables, serving more than 2 fixed landings of a construction, for lifting goods, with a vertical travel speed not exceeding 0,15 m/s (EN 1570-2:2016);
-   lifting tables, serving more than 2 fixed landings of a construction, for lifting operators, with a vertical travel speed not exceeding 0,15 m/s;
-   lifting tables carrying operators and installed in full enclosures with a vertical travel speed not exceeding 0,15 m/s;
-   lifting tables used on ships;
-   lifting tables designed for artists and stage set features during artistic performances (EN 17206:2020);
-   power operated lifting platforms for persons with impaired mobility (EN 81-41:2010);
-   mobile lifting tables for airport ground support equipment (EN 1915-2:2001+A1:2009 and EN 12312-1:2013);
-   mobile elevating work platforms (EN 280-1:2022);
-   static Group B elevating work platforms (EN 280-1:2022);
-   vehicle servicing lifts (EN 1493:2022);
-   mobile lifting tables used for firefighting (EN 1777:2010);
-   mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
-   rail dependent storage and retrieval equipment (EN 528:2021+A1:2022);
-   scissor lift pallet trucks (EN ISO 3691-5:2015, including EN ISO 3691-5:2015/AC:2016 and EN ISO 3691-5:2015/A1:2020);
-   lifting tables suspended from a ceiling.
1.4   This document does not consider the additional requirements for:
-   electromagnetic compatibility;
-   operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
-   operation subject to special rules (e.g. potentially explosive atmospheres, mines);
-   handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes));
-   hazards occurring during construction, transportation, and disposal;
-   equipment installed on the load platform or the replacing or maintaining of it;
-   integration into broader systems or other machines, etc.;
-   cable-less controls, i.e. wireless;
-   lifting tables where the hydraulic pressure is derived directly from gas pressure;
-   lifting tables powered by internal combustion engines.

  • Draft
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7965-1:2024(Main)
Packaging - Drop test - Part 1: Paper sacks (ISO 7965-1:2024)
kSIST FprEN ISO 7965-1:2024

This document specifies a method of vertical impact testing on a filled paper sack by dropping. It is performed either as a single test to investigate the effects of vertical impact or as part of a sequence of tests designed to measure the ability of a sack to withstand a distribution system that includes a vertical impact hazard.
This document specifies the testing procedure and how the results of tests are presented. It is based on ISO 2248 but is specifically related to paper sacks.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day