EN 15266:2007

Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar

This European Standard specifies the requirements for material, design, manufacture, testing, marking and documentation of stainless steel pliable corrugated gas tubing kits for buildings with a maximum operating pressure (MOP) less than or equal to 0,5 bar and a nominal size range from DN 10 to DN 50.
This document applies to stainless steel pliable corrugated gas tubing kits used for 1st, 2nd and 3rd family gases in residential, commercial and industrial gas installations.
This document does not apply to:
   pliable tubing without cover;
   corrugated safety metal hose assemblies for connection to moveable appliances.
This document does not cover the installation aspects of stainless steel pliable corrugated gas tubing kits.

Nichtrostende biegbare Wellrohrbausätze in Gebäuden für Gas mit einem Arbeitsdruck bis 0,5 bar

Diese Europaische Norm legt die Anforderungen an Werkstoff, Auslegung, Herstellung, Prufung, Kennzeich-nung
und Dokumentation von nichtrostenden biegbaren Wellrohrsystemen fur Gas in Gebauden und fur einen
maximalen Arbeitsdruck ¡Â0,5 bar fest, bei einem Nennweitenbereich von DN 10 bis DN 50.
Dieses Dokument gilt fur neu installierte Anlagen sowie fur Austausch, Erweiterung oder Anderung bestehen-der
Systeme fur Gase der 1., 2. und 3. Familie. Nichtrostende biegbare Wellrohrsysteme fur Gas konnen in
Verbindung mit anderen zugelassenen Rohrleitungssystemen fur Gas verwendet werden.
ANMERKUNG Festlegung von Gasen der 1., 2. und 3. Familie, siehe EN 437:2003.
Dieses Dokument gilt nicht fur:
.biegbare Wellrohrsysteme ohne Ummantelung;
.gewellte Sicherheits-Gasschlauchleitungen aus Metall fur den Anschluss von beweglichen Geraten.
Dieses Dokument behandelt keine Anforderungen bezogen auf den Einbau von nichtrostenden biegbaren
Wellrohrsystemen fur Gas, welche ortlichen und/oder nationalen Regelungen mit verbindlich vorgeschrie-
benen Festigkeits- und Dichtheitsprufungen vor der Inbetriebnahme unterliegen konnen.

Kits de tuyaux onduleux pliables en acier inoxydable pour le gaz dans les bâtiments avec une pression de service inférieure ou égale à 0,5 bar

La présente Norme européenne définit les prescriptions relatives au matériau, à la conception, à la fabrication, aux essais, au marquage et à la documentation des kits de tuyaux onduleux pliables en acier inoxydable pour le gaz dans les bâtiments avec une pression maximale de service (MOP) inférieure ou égale à 0,5 bar, et une gamme de diamètres nominaux compris entre DN 10 et DN 50.
Le présent document s'applique aux kits de tuyaux onduleux pliables en acier inoxydable destinés à être utilisés avec les première, deuxième et troisième familles de gaz dans les installations gaz pour le résidentiel, le commercial et l’industriel.
Le présent document ne s'applique pas :
   aux tuyaux pliables sans protection ;
   aux tuyaux métalliques flexibles onduleux de sécurité pour le raccordement d'appareils mobiles.
Le présent document ne traite pas des aspects liés à l'installation des kits de tuyaux onduleux pliables en acier inoxydable pour le gaz.

Upogljivi valoviti cevni kompleti iz nerjavnega jekla za plin v stavbah z delovnim tlakom do 0,5 bara

General Information

• Status: Published
• Publication Date: 08-May-2007
• Withdrawal Date: 27-Feb-2009
• ICS: 23.040.01 - Pipeline components and pipelines in general
• Technical Committee: CEN/TC 342 - Metal hoses, hose assemblies, bellows and expansion joints
• Drafting Committee: CEN/TC 342/WG 1 - Hose assemblies and fittings
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 09-May-2007
• Completion Date: 09-May-2007
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
• Ref Project: SIST EN 15266:2007 - Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar

Relations

• Revised: prEN 15266 - Stainless steel pliable corrugated tubing kits for gas installation pipework with an operating pressure up to 0,2 MPa (2 bar)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Upogljivi valoviti cevni kompleti iz nerjavnega jekla za plin v stavbah z delovnim tlakom do 0,5 baraNichtrostende biegbare Wellrohrbausätze in Gebäuden für Gas mit einem Arbeitsdruck bis 0,5 barKits de tuyaux onduleux pliables en acier inoxydable pour le gaz dans les bâtiments avec une pression de service inférieure ou égale a 0,5 barStainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar91.140.40Sistemi za oskrbo s plinomGas supply systems77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific useICS:Ta slovenski standard je istoveten z:EN 15266:2007SIST EN 15266:2007en,de01-junij-2007SIST EN 15266:2007SLOVENSKI
STANDARD



SIST EN 15266:2007



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15266May 2007ICS 23.040.01 English VersionStainless steel pliable corrugated tubing kits in buildings for gaswith an operating pressure up to 0,5 barKits de tuyaux onduleux pliables en acier inoxydable pour legaz dans les bâtiments avec une pression de serviceinférieure ou égale à 0,5 barNichtrostende biegbare Wellrohrbausätze in Gebäuden fürGas mit einem Arbeitsdruck bis 0,5 barThis European Standard was approved by CEN on 17 February 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15266:2007: ESIST EN 15266:2007



EN 15266:2007 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms, definitions and abbreviations.7 4 Design requirements.8 4.1 General.8 4.2 Materials.8 4.3 Nominal size DN and pressure drop.9 4.4 Threads.9 4.5 PLT fittings.9 4.6 Seals and sealing agents.10 4.7 Environment.10 4.8 Supports.10 4.9 Electrical conductivity requirements.10 4.10 Cover.
...