iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 15416-5

(Main)

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions

This document specifies a laboratory method of determining the minimum pressing time for line thicknesses close contact, 0,2 mm, 0,3 mm and 0,5 mm, at three temperatures and three wood moisture contents.
This document is intended to determine the minimum pressing time using a defined procedure for obtaining a reliable base for comparison of minimum pressing time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence in variation of factors such as timber density, moisture content, factory temperature and relative air humidity.

Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste - Prüfverfahren - Teil 5: Bestimmung der Mindestpresszeit bei Referenzbedingungen

Dieses Dokument legt ein Laborverfahren zur Bestimmung der Mindestpresszeit für die Klebstofffugendicken dünn, 0,2 mm, 0,3 mm und 0,5 mm bei drei Temperaturen und drei Holzfeuchten fest.
Dieses Dokument ist zur Bestimmung der Mindestpresszeit mit einem festgelegten Verfahren vorgesehen, um eine zuverlässige Grundlage zum Vergleich der Mindestpresszeiten verschiedener Klebstoffe bei Referenzbedingungen zu schaffen.
Das Verfahren führt zu einem Ergebnis, das für die sichere Herstellung von Holzbauteilen nur unter Berücksichtigung der Einflussfaktoren, wie z. B. Rohdichte und Feuchtegehalt des Holzes, Werkstemperatur und relative Luftfeuchte, zugrunde gelegt werden kann.

Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste - Méthodes d'essais - Partie 5 : Détermination du temps de pressage minimal dans des conditions de référence

Le présent document spécifie une méthode de détermination en laboratoire du temps de pressage minimal pour des joints minces de 0,2 mm, 0,3 mm et 0,5 mm, à trois températures et trois teneurs en humidité du bois.
Le présent document est destiné à déterminer le temps de pressage minimal en utilisant un mode opératoire défini afin d’obtenir une base fiable de comparaison des temps de pressage minimaux de différents adhésifs dans des conditions de référence.
La méthode conduit à un résultat qui ne peut pas être utilisé pour une fabrication sûre des structures en bois sans tenir compte de l’influence de facteurs tels que la masse volumique du bois, sa teneur en humidité, la température de l’usine et l’humidité relative de l’air.

Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne metode - 5. del: Ugotavljanje najkrajšega časa stiskanja pri referenčnih pogojih

General Information

Status
Not Published
Publication Date
18-Sep-2025
ICS
83.180 - Adhesives
Technical Committee
CEN/TC 193 - Adhesives
Drafting Committee
CEN/TC 193/SC 1/WG 4 - Tests for 'Novel' load bearing adhesives for wood
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
02-May-2024
Due Date
03-May-2024
Completion Date
02-May-2024
Ref Project
oSIST prEN 15416-5:2024 - Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions

Relations

Revises
EN 15416-5:2017 - Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions
Effective Date
14-Jun-2023

Buy Standard

prEN 15416-5:2024prEN 15416-5:2024
PreviousNext
Draft
prEN 15416-5:2024
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15416-5:2024
01-junij-2024
Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne
metode - 5. del: Ugotavljanje najkrajšega časa stiskanja pri referenčnih pogojih
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test
methods - Part 5: Determination of minimum pressing time under referenced conditions
Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und
Aminoplaste - Prüfverfahren - Teil 5: Bestimmung der Mindestpresszeit bei
Referenzbedingungen
Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste -
Méthodes d'essais - Partie 5 : Détermination du temps de pressage minimal dans des
conditions de référence
Ta slovenski standard je istoveten z: prEN 15416-5
ICS:
83.180 Lepila Adhesives
91.080.20 Lesene konstrukcije Timber structures
oSIST prEN 15416-5:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15416-5:2024

---------------------- Page: 2 ----------------------
oSIST prEN 15416-5:2024


DRAFT
EUROPEAN STANDARD
prEN 15416-5
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2024
ICS 83.180 Will supersede EN 15416-5:2017
English Version

Adhesives for load bearing timber structures other than
phenolic and aminoplastic - Test methods - Part 5:
Determination of minimum pressing time under
referenced conditions
Adhésifs pour structures portantes en bois de type Klebstoffe für tragende Holzbauteile ausgenommen
autre que phénolique et aminoplaste - Méthodes Phenolharzklebstoffe und Aminoplaste - Prüfverfahren
d'essais - Partie 5 : Détermination du temps de - Teil 5: Bestimmung der Mindestpresszeit bei
pressage minimal dans des conditions de référence Referenzbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 193.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15416-5:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15416-5:2024
prEN 15416-5:2024 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 8
5 Apparatus .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 10364:2024(Main)
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2024)
SIST EN ISO 10364:2024

This document specifies methods for determining the pot life of multi-part adhesives, in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The different methods described in this document to measure the property do not necessarily provide identical results.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1       Some of the methods described in this document can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2       This document can also be used for assessing non-structural adhesives.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21368:2023(Main)
Adhesives - Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures (ISO 21368:2022)
SIST EN ISO 21368:2023

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following:
—    a contract between the parties involved;
—    an application standard;
—    a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6076:2023(Main)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023, Corrected version 2023-09)
SIST EN ISO 6076:2023

This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-8:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond line specimens in compression shear
SIST EN 302-8:2023

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16254:2023(Main)
Adhesives - Emulsion polymer isocyanate (EPI) for load-bearing timber structures - Classification and performance requirements
SIST EN 16254:2023

This document establishes a classification for emulsion polymer isocyanate (EPI) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the industrial manufacture of load-bearing timber products only.
The performance requirements of this document are applicable to the adhesives only, not to the timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
Such an adhesive meeting the requirements of this document for its type is adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-7:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 7: Determination of the working life under referenced conditions
SIST EN 302-7:2023

This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test.
This method does not apply to determining the working life of a multi-component adhesive whose actual working life is very short.
This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-1:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 1: Determination of longitudinal tensile shear strength
SIST EN 302-1:2023

This document specifies a method for determining the shear strength of adhesive bonds in close contact glue line and thick glue line.
It is applicable to the following applications:
a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended for use to provide for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 301:2023(Main)
Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements
SIST EN 301:2023

This document establishes a classification for phenolic and aminoplastic polycondensation adhesives according to their suitability for use for load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber products only.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-3:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength
SIST EN 302-3:2023

This document specifies a method for determining the effect on bond strength of damage to wood fibres caused by the action of acids from the adhesive or primer used in the gluing process during climatic cycling.
It is applicable to the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425 and EN 16254;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for determining if the adhesive after bonding has a damaging influence on the strength of the wood due to chemical action.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.) or Beech (Fagus sylvatica L.).
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-5:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
SIST EN 302-5:2023

This document specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65].
This document is applicable to obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day