EN 915:2008

Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety

This European Standard specifies functional requirements (see Clause 3) and specific safety requirements in addition to the general safety requirements in EN 913 (see Clause 4).
This European Standard is applicable to 2 types of asymmetric bars (see Table 1).

Turngeräte - Stufenbarren - Anforderungen und Prüfverfahren einschließlich Sicherheit

Diese Norm legt funktionelle Anforderungen (siehe Abschnitt 3) und spezifische sicherheitstechnische Anforderungen zusätzlich zu den allgemeinen Sicherheitsanforderungen in EN 913 (siehe Abschnitt 4) fest.
Diese Norm gilt für zwei Typen von Stufebarren (siehe Tabelle 1).

Matériel de gymnastique - Barres asymétriques - Exigences et méthodes d'essai y compris de sécurité

La présente Norme européenne fixe des exigences fonctionnelles (voir Article 3) et des exigences spécifiques de sécurité qui s'ajoutent aux exigences générales de sécurité spécifiées dans l'EN 913 (voir Article 4), qui doit être lue en liaison avec cette norme.
La présente Norme européenne s'applique aux deux types de barres asymétriques (voir Tableau 1) destinés à être utilisés sous surveillance d'une personne compétente.

Gimnastična oprema - Dvovišinska bradlja - Zahteve in preskusne metode, vključno z varnostjo

General Information

• Status: Published
• Publication Date: 04-Nov-2008
• ICS: 97.220.30 - Indoor sports equipment
• Technical Committee: CEN/TC 136 - Sports, playground and other recreational equipment
• Drafting Committee: CEN/TC 136/WG 22 - Gymnastic and playing field equipment
• Current Stage: 9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
• Completion Date: 08-Apr-2019
• Directive: 2001/95/EC - Directive 2001/95/EC of the European Parliament and of the Council of 3 December 2001 on general product safety
• Directive: 92/59/EEC - General product safety
• Mandate: M/507 - Standardisation mandate issued to the European standardisation organisations (ESOs) to develop European standards for gymnastic equipment
• Ref Project: SIST EN 915:2009 - Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety

Relations

• Replaces: EN 915:1996 - Gymnastic equipment - Asymmetric bars - Functional and safety requirements, test methods
• Effective Date: 22-Dec-2008
• Revised: FprEN 915 - Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 915:2009
01-januar-2009
1DGRPHãþD
SIST EN 915:1996
*LPQDVWLþQDRSUHPD'YRYLãLQVNDEUDGOMD=DKWHYHLQSUHVNXVQHPHWRGH
YNOMXþQR]YDUQRVWMR
Gymnastic equipment - Asymmetric bars - Requirements and test methods including
safety
Turngeräte - Stufenbarren - Anforderungen und Prüfverfahren einschließlich Sicherheit
Matériel de gymnastique — Barres asymétriques — Exigences et méthodes d'essai y
compris la sécurité
Ta slovenski standard je istoveten z: EN 915:2008
ICS:
97.220.30 Oprema za dvoranske športe Indoor sports equipment
SIST EN 915:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 915:2009

---------------------- Page: 2 ----------------------

SIST EN 915:2009
EUROPEAN STANDARD
EN 915
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2008
ICS 97.220.30 Supersedes EN 915:1996
English Version
Gymnastic equipment - Asymmetric bars - Requirements and
test methods including safety
Matériel de gymnastique - Barres asymétriques - Exigences Turngeräte - Stufenbarren - Anforderungen und
et méthodes d'essai y compris la sécurité Prüfverfahren einschließlich Sicherheit
This European Standard was approved by CEN on 27 September 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 915:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 915:2009
EN 915:2008 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Requirements.4
3.1 Classification.4
3.2 Dimensions.4
4 Safety requirements .6
4.1 General requirements.6
4.2 Entrapment .6
4.3 Stability .6
4.4 Vertical stiffness and residual deflection.6
4.5 Strength .6
4.6 Rigidity of framework .6
5 Test methods.6
5.1 General.
...