iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 80601-2-72:2023

(Main)

Medical electrical equipment - Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients (ISO 80601-2-72:2023)

Medical electrical equipment - Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients (ISO 80601-2-72:2023)

This document applies to the basic safety and essential performance of a ventilator in combination with its accessories, hereafter referred to as ME equipment:
—    intended for use in the home healthcare environment;
—    intended for use by a lay operator; and
—    intended for those patients who need differing levels of support from artificial ventilation including for ventilator-dependent patients.
This document is also applicable to those accessories intended by their manufacturer to be connected to a ventilator breathing system or to a ventilator where the characteristics of those accessories can affect the basic safety or essential performance of the ventilator.

Medizinische elektrische Geräte - Teil 2-72: Besondere Festlegungen für die Sicherheit einschließlich der wesentlichen Leistungsmerkmale von Heimbeatmungsgeräten für vom Gerät abhängige Patienten (ISO 80601-2-72:2023)

No scope available

Appareils électromédicaux - Partie 2-72: Exigences particulières pour la sécurité de base et les performances essentielles des ventilateurs utilisés dans l'environnement des soins à domicile pour les patients ventilo-dépendants (ISO 80601-2-72:2023)

Le présent document s’applique à la sécurité de base et aux performances essentielles d’un ventilateur associé à ses accessoires, ci-après désignés par appareil EM :
—    destiné à être utilisé dans l’environnement des soins à domicile ;
—    destiné à être utilisé par un opérateur non spécialiste ; et
—    prévu pour les patients qui nécessitent différents niveaux d’aide par ventilation artificielle, y compris pour les patients ventilo-dépendants.
Le présent document s’applique également aux accessoires conçus par leur fabricant pour être raccordés au système respiratoire d’un ventilateur ou à un ventilateur, lorsque les caractéristiques de ces accessoires peuvent affecter la sécurité de base ou les performances essentielles du ventilateur.

Medicinska električna oprema - 2-72. del: Posebne zahteve za osnovno varnost in bistvene lastnosti respiratorjev za oskrbo od aparata odvisnih pacientov na domu (ISO 80601-2-72:2023)

Standard ISO 80601-2-72:2015 se uporablja za osnovno varnost in bistvene lastnosti respiratorjev v kombinaciji z dodatno opremo, v nadaljevanju: elektromedicinska oprema:
   za uporabo v okolju domače zdravstvene oskrbe;
   ki je namenjena nestrokovnjakom;
   namenjena pacientom, ki so odvisni od mehanskega respiratorja za ohranjanje pri življenju.
Standard ISO 80601-2-72:2015 se uporablja tudi za tisto dodatno opremo, ki jo je proizvajalec predvidel za priklop na ventilatorski dihalni sistem ali respirator, pri čemer lahko lastnosti te dodatne opreme vplivajo na osnovno varnost ali bistvene lastnosti respiratorja.
Standard ISO 80601-2-72:2015 je posamezni mednarodni standard iz skupin standardov IEC 60601‑1 in ISO/IEC 80601.

General Information

Status
Published
Publication Date
11-Jul-2023
ICS
11.040.10 - Anaesthetic, respiratory and reanimation equipment
Technical Committee
CEN/TC 215 - Respiratory and anaesthetic equipment
Drafting Committee
CEN/TC 215/WG 2 - Lung ventilators
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
12-Jul-2023
Completion Date
12-Jul-2023
Ref Project
SIST EN ISO 80601-2-72:2023 - Medical electrical equipment - Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients (ISO 80601-2-72:2023)

Relations

Replaces
EN ISO 80601-2-72:2015 - Medical electrical equipment - Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients (ISO 80601-2-72:2015)
Effective Date
18-Jan-2023

Buy Standard

EN ISO 80601-2-72:2023 - BARVEEN ISO 80601-2-72:2023 - BARVE
PreviousNext
Standard
EN ISO 80601-2-72:2023 - BARVE
English language
152 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 80601-2-72:2023
01-oktober-2023
Nadomešča:
SIST EN ISO 80601-2-72:2015
Medicinska električna oprema - 2-72. del: Posebne zahteve za osnovno varnost in
bistvene lastnosti respiratorjev za oskrbo od aparata odvisnih pacientov na domu
(ISO 80601-2-72:2023)
Medical electrical equipment - Part 2-72: Particular requirements for basic safety and
essential performance of home healthcare environment ventilators for ventilator-
dependent patients (ISO 80601-2-72:2023)
Medizinische elektrische Geräte - Teil 2-72: Besondere Festlegungen für die Sicherheit
einschließlich der wesentlichen Leistungsmerkmale von Heimbeatmungsgeräten für vom
Gerät abhängige Patienten (ISO 80601-2-72:2023)
Appareils électromédicaux - Partie 2-72: Exigences particulières pour la sécurité de base
et les performances essentielles des ventilateurs utilisés dans l'environnement des soins
à domicile pour les patients ventilo-dépendants (ISO 80601-2-72:2023)
Ta slovenski standard je istoveten z: EN ISO 80601-2-72:2023
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
SIST EN ISO 80601-2-72:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 80601-2-72:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 80601-2-72:2023


EN ISO 80601-2-72
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2023
EUROPÄISCHE NORM
ICS 11.040.10 Supersedes EN ISO 80601-2-72:2015
English Version

Medical electrical equipment - Part 2-72: Particular
requirements for basic safety and essential performance of
home healthcare environment ventilators for ventilator-
dependent patients (ISO 80601-2-72:2023)
Appareils électromédicaux - Partie 2-72: Exigences Medizinische elektrische Geräte - Teil 2-72: Besondere
particulières pour la sécurité de base et les Festlegungen für die Sicherheit einschließlich der
performances essentielles des ventilateurs utilisés wesentlichen Leistungsmerkmale von
dans l'environnement des soins à domicile pour les Heimbeatmungsgeräten für vom Gerät abhängige
patients ventilo-dépendants (ISO 80601-2-72:2023) Patienten (ISO 80601-2-72:2023)
This European Standard was approved by CEN on 24 April 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 80601-2-72:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 80601-2-72:2023
EN ISO 80601-2-72:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 80601-2-72:2023
EN ISO 80601-2-72:2023 (E)
European foreword
This document (EN ISO 80601-2-72:2023) has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment" in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2024, and conflicting national standards shall
be withdrawn at the latest by January 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 806
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 15002:2024(Main)
Flow control devices for connection to a medical gas supply system (ISO 15002:2023)
SIST EN ISO 15002:2024

This document specifies requirements for flow control devices that can be connected by the user either directly, by means of a probe or a gas-specific connector, or indirectly by means of a low-pressure hose assembly conforming with ISO 5359 to:
a)    a terminal unit conforming with ISO 9170-1 of a medical gas pipeline system conforming with ISO 7396-1:2016;
b)    the pressure outlet of a regulator conforming with ISO 10524-1:2018; or
c)    to the pressure outlet of a valve integrated pressure regulator (VIPR) conforming with ISO 10524-3 (see 5.2 gas inlets).
This document applies to the following types of flow control devices (FCDs):
a)    flowmeters;
b)    flowgauge FCDs; and
c)    fixed orifice FCDs.
NOTE       Flow control devices that are classed as medical electrical equipment can be subject to additional requirements of IEC 60601-1.
This document applies to flow control devices for the following gases:
—    oxygen;
—    oxygen 93 %;
—    nitrous oxide;
—    medical air;
—    carbon dioxide;
—    oxygen/nitrous oxide mixture 50/50 (% volume fraction);
—    oxygen-enriched air;
—    helium;
—    xenon; and
—    specified mixtures of the gases listed above.
NOTE Flow control devices can be available for other gases.
This document does not apply to flow control devices that are:
a)    for use with gases for driving surgical tools;
b)    an integral part of a regulator (see ISO 10524-1:2018); or
c)           an integral part of a valve with integrated pressure regulator (VIPR) (see ISO 10524-3).

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-55:2018/A1:2023(Amendment)
Medical electrical equipment - Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors - Amendment 1 (ISO 80601-2-55:2018/Amd 1:2023)
SIST EN ISO 80601-2-55:2018/A1:2024
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-84:2023(Main)
Medical electrical equipment - Part 2-84: Particular requirements for the basic safety and essential performance of ventilators for the emergency medical services environment (ISO 80601-2-84:2023)
SIST EN ISO 80601-2-84:2024

This document applies to the basic safety and essential performance of an EMS ventilator in combination with its accessories, hereafter also referred to as ME equipment:
¾     intended for patients who need differing levels of support from artificial ventilation including ventilator-dependent patients;
¾     intended to be operated by a healthcare professional operator;
¾     intended for use in the EMS environment; and
¾     intended for invasive or non-invasive ventilation.
NOTE 2     An EMS ventilator can also be used for transport within a professional healthcare facility.
An EMS ventilator is not considered to use a physiologic closed loop-control system unless it uses a physiological patient variable to adjust the  artificial ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to the ventilator breathing system, or to an EMS ventilator, where the characteristics of those accessories can affect the basic safety or essential performance of the EMS ventilator.
NOTE 3     If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1.
NOTE 4     Additional information can be found in IEC 60601-1:2005+AMD1:2012+AMD2:2020, 4.2.
This document does not specify the requirements for the following:
NOTE 5     See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient. 
¾     ventilators or accessories intended for ventilator-dependent patients in critical care applications, which are given in ISO 80601-2-12.
¾     ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601-2-72.
¾     ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‑2‑13.
¾     ventilators or accessories intended for ventilatory support equipment (intended only to augment the ventilation of spontaneously breathing patients), which are given in ISO 80601‑2-79 and ISO 80601-2-80.
¾     obstructive sleep apnoea therapy ME equipment, which are given in ISO 80601‐2‐70.
¾     user-powered resuscitators, which are given in ISO 10651‐4.
¾     gas-powered emergency resuscitators, which are given in ISO 10651‐5.
¾     continuous positive airway pressure (CPAP) ME equipment.
¾     high‐frequency jet ventilators (HFJVs), which are given in ISO 80601-2-87.
¾     high‐frequency oscillatory ventilators (HFOVs)[44], which are given in ISO 80601-2-87.
NOTE 6      An EMS ventilator can incorporate high-frequency jet or high-frequency oscillatory ventilation-modes.
¾     respiratory high-flow therapy equipment, which are given in ISO 80601-2-90.
NOTE 7      An EMS ventilator can incorporate high-flow therapy operational mode, but such a mode is only for spontaneously breathing patients.
¾     oxygen therapy constant flow ME equipment.
¾     cuirass or “iron‐lung” ventilators.

  • Standard
    149 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-12:2023(Main)
Medical electrical equipment - Part 2-12: Particular requirements for basic safety and essential performance of critical care ventilators (ISO 80601-2-12:2023)
SIST EN ISO 80601-2-12:2024

This document applies to the basic safety and essential performance of a critical care ventilator in combination with its accessories, hereafter referred to as ME equipment:
¾     intended for use in an environment that provides specialized care for patients whose conditions can be life-threatening and who can require comprehensive care and constant monitoring in a professional healthcare facility;
NOTE 2      For the purposes of this document, such an environment is referred to as a critical care environment. Ventilators for this environment are considered life-sustaining.
NOTE 3      For the purposes of this document, such a critical care ventilator can provide ventilation during transport within a professional healthcare facility (i.e. be a transit-operable ventilator).
NOTE 4      A critical care ventilator intended for use in transport within a professional healthcare facility is not considered as an emergency medical services environment ventilator.
¾     intended to be operated by a healthcare professional operator; and
¾     intended for those patients who need differing levels of support from artificial ventilation including for ventilator-dependent patients.
A critical care ventilator is not considered to use a physiologic closed-loop-control system unless it uses a physiological patient variable to adjust the artificial ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to a ventilator breathing system, or to a ventilator, where the characteristics of those accessories can affect the basic safety or essential performance of the ventilator.
NOTE 5     If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601-1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1.
NOTE 6     Additional information can be found in IEC 60601-1:2005+AMD1:2012+AMD2:2020, 4.2.
This document is not applicable to ME equipment or an ME system operating in a ventilator-operational mode solely intended for patients who are not dependent on artificial ventilation.
NOTE 7     A critical care ventilator, when operating in such a ventilator-operational mode, is not considered life-sustaining.
This document is not applicable to ME equipment that is intended solely to augment the ventilation of spontaneously breathing patients within a professional healthcare facility.
This document does not specify the requirements for:
NOTE 8     See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient.
¾     ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‑2‑13;
¾     ventilators or accessories intended for the emergency medical services environment, which are given in ISO 80601-2-84;
¾     ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601‑2-72;
¾     ventilators or accessories intended for home-care ventilatory support devices, which are given in ISO 80601-2-79 and ISO 80601-2-80;
¾     obstructive sleep a

  • Standard
    168 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10524-1:2019/A1:2023(Amendment)
Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices - Amendment 1 (ISO 10524-1:2018/Amd 1:2023)
SIST EN ISO 10524-1:2019/A1:2024
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5367:2023(Main)
Anaesthetic and respiratory equipment - Breathing sets and connectors (ISO 5367:2023)
SIST EN ISO 5367:2023

This document specifies minimum requirements for breathing sets and breathing tubes intended to be used with anaesthetic breathing systems, ventilator breathing systems, humidifiers or nebulizers. It applies to breathing sets and breathing tubes and patient end adaptors supplied already assembled and to those supplied as components and assembled in accordance with the manufacturer’s instructions.
This document is applicable to breathing sets which include special components (e.g. water traps) between the patient end and machine end.
Provision is made for coaxial and related bifurcated, double-lumen, or multiple-lumen breathing sets and breathing tubes suitable for use with patient end adaptors.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 27427:2023(Main)
Anaesthetic and respiratory equipment - Nebulizing systems and components (ISO 27427:2023)
SIST EN ISO 27427:2023

This document specifies requirements for the safety and performance testing of general-purpose nebulizing systems intended for continuous or breath-actuated delivery of liquids, in aerosol form, to humans through the respiratory system.
This document includes gas-powered nebulizers (which can be powered by, e.g., compressors, pipeline systems, cylinders, etc.) and electrically powered nebulizers [e.g. spinning disc, ultrasonic, vibrating mesh (active and passive), and capillary devices] or manually powered nebulizers. This document does not specify the electrical requirements of electrically powered nebulizers.
This document does not specify the minimum performance of nebulizing systems.
This document does not apply to:
a)       devices intended for nasal deposition;
b)       devices intended solely to provide humidification or hydration by providing water in aerosol form.
NOTE 1        ISO 80601-2-74 and ISO 20789 cover these devices.
c)        drug-specific nebulizers or their components (e.g. metered dose inhalers, metered liquid inhalers, dry powder inhalers).
NOTE 2        ISO 20072 covers these devices.
NOTE 3        See Annex A for rationale.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10651-4:2023(Main)
Lung ventilators - Part 4: Particular requirements for user-powered resuscitators (ISO 10651-4:2023)
SIST EN ISO 10651-4:2023

This document specifies requirements for user-powered resuscitators intended for use with all age groups and which are intended to provide lung ventilation to patients whose breathing is inadequate. User-powered resuscitators are designated according to ideal body mass range.
Example user-powered resuscitators include:
—    self-inflating bag resuscitators intended to be squeezed by the user’s hand and refilled by elastic recoil; and
NOTE 1    Self-inflating bag resuscitators are generally transit-operable and can be used in a wide range of environmental and emergency situations.
—    flow-inflating bag resuscitators intended to be squeezed by the user’s hand and refilled by a flow from a medical gas source.
This document is also applicable to those accessories that are intended for use with resuscitators where the characteristics of those accessories can affect the safety of the user-powered resuscitator.
Examples of such accessories include face masks, PEEP valves, capnometric indicators, manometers, metronomes, flow restrictors, filters, gas refill valves, oxygen gas mixers, connectors, electronic feedback devices, electronic sensors and transmission of data to other equipment.
This document is also applicable to point-of-use packaging.
This document does not specify the requirements for:
—    gas-powered emergency resuscitators, which are given in ISO 10651-5;
—    electrically-powered resuscitators;
—    gas powered resuscitators for professional healthcare facilities; and
—    anaesthetic reservoir bags, which are given in ISO 5362.
NOTE 2    This document has been prepared to address the relevant essential principles[24] and labelling[25] guidances of the International Medical Devices Regulators Forum (IMDRF) as indicated in Annex D.
NOTE 3    This document has been prepared to address the relevant essential principles of safety and performance of ISO 16142-1:2016 as indicated in Annex E.
NOTE 4    This document has been prepared to address the relevant general safety and performance requirements of European regulation (EU) 2017/745[23] as indicated in Annex F.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5361:2023(Main)
Anaesthetic and respiratory equipment - Tracheal tubes and connectors (ISO 5361:2023, Corrected version 2023-11)
SIST EN ISO 5361:2023

This document provides specific requirements for the basic safety and essential performance for oro-tracheal and naso-tracheal tubes and tracheal tube connectors, tracheal tubes with walls reinforced with metal or plastic, tracheal tubes with shoulders, tapered tracheal tubes, tracheal tubes with means for suctioning, monitoring or delivery of drugs or other gases, and the many other types of tracheal tubes devised for specialized applications.
Tracheobronchial (including endobronchial) tubes (see ISO 16628), tracheostomy tubes (see ISO 5366), and supralaryngeal airways (see ISO 11712) are excluded from the scope of this document.
Tracheal tubes intended for use with flammable anaesthetic gases or agents, lasers, or electrosurgical equipment are outside the scope of this document.
NOTE 1      There is guidance or rationale for this clause contained in Annex A.2.
NOTE 2      ISO 11990-1, ISO 11990-2, and ISO 14408 deal with laser surgery of the airway.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21917:2022(Main)
Anaesthetic and respiratory equipment - Voice prostheses (ISO 21917:2021)
SIST EN ISO 21917:2023

This document specifies performance requirements for voice prostheses including requirements for marking, packaging and information to be provided by the manufacturer as well as test methods for the evaluation of physical characteristics of voice prostheses.
NOTE      There is guidance or rationale for this list item contained in A.2.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day