Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2020)

1.1  This document gives a general test method for the determination of the temperature of deflection under load (flexural stress under three-point loading) of plastics. Different types of test specimen and different constant loads are defined to suit different types of material.
1.2  ISO 75-2 gives specific requirements for plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite, while ISO 75-3 gives specific requirements for high-strength thermosetting laminates and long-fibre-reinforced plastics in which the fibre length, prior to processing, is greater than 7,5 mm.
1.3  The methods specified are suitable for assessing the relative behaviour of different types of material at elevated temperature under load at a specified rate of temperature increase. The results obtained do not necessarily represent maximum applicable temperatures because, in practice, essential factors, such as time, loading conditions and nominal surface stress, can differ from the test conditions. True comparability of data can only be achieved for materials having the same room-temperature flexural modulus.
1.4  The methods specify preferred dimensions for the test specimens.
1.5  Data obtained using the test methods described are not intended to be used to predict actual end-use performance. The data are not intended for design analysis or prediction of the endurance of materials at elevated temperatures.
1.6  This method is commonly known as the heat deflection temperature or heat distortion temperature (HDT) test, although there is no official document using this designation.

Kunststoffe - Bestimmung der Wärmeformbeständigkeitstemperatur - Teil 1: Allgemeines Prüfverfahren (ISO 75-1:2020)

1.1 Dieses Dokument legt ein allgemeines Prüfverfahren zur Bestimmung der Wärmeformbeständigkeits¬temperatur von Kunststoffen unter Last (Biegespannung unter Dreipunktbelastung) fest. Für verschiedene Werkstoffarten sind unterschiedliche Arten von Probekörpern und unterschiedliche konstante Lasten festgelegt.
1.2 ISO 75 2 legt spezielle Anforderungen an Kunststoffe (einschließlich gefüllte Kunststoffe und lang¬faserverstärkte Kunststoffe, bei denen die Faserlänge vor der Verarbeitung bis zu 7,5 mm beträgt) und Hartgummi fest, während ISO 75 3 spezielle Anforderungen an hochfeste, aushärtbare Schichtstoffe und langfaserverstärkte Kunststoffe festlegt, bei denen die Faserlänge vor der Verarbeitung mehr als 7,5 mm beträgt.
1.3 Die festgelegten Verfahren sind geeignet, das relative Verhalten verschiedener Werkstoffe bei erhöhter Temperatur abzuschätzen, wenn die Temperatur unter Belastung mit einer vorgegebenen Heizrate erhöht wird. Die erhaltenen Ergebnisse stellen nicht unbedingt die maximalen Gebrauchstemperaturen dar, weil sich in der Praxis wesentliche Faktoren wie Zeit, Belastungsbedingungen und nominelle Oberflächen¬spannung von den Prüfbedingungen unterscheiden können. Eine wirkliche Vergleichbarkeit der Daten kann nur bei Werkstoffen mit dem gleichen Biegemodul bei Raumtemperatur erreicht werden.
1.4 Die Verfahren legen Vorzugsmaße der Probekörper fest.
1.5 Die mit den beschriebenen Prüfverfahren ermittelten Daten sind nicht für eine Voraussage der Gebrauchstauglichkeit vorgesehen. Die Daten sind nicht zur Analyse der Gestaltung und Bemessung oder Vorhersage des Langzeitverhaltens (Lebensdauer) bei erhöhten Temperaturen von Werkstoffen vorgesehen.
1.6 Dieses Verfahren ist allgemein als Prüfung der Wärmestandfestigkeit bzw. Wärmeformbeständigkeit (HDT Prüfung, en: Heat Deflection Temperature bzw. Heat Distortion Temperature Test) bekannt, obwohl es kein offizielles Dokument gibt, in dem diese Benennung verwendet wird.

Plastiques - Détermination de la température de fléchissement sous charge - Partie 1: Méthode d'essai générale (ISO 75-1:2020)

1      Domaine d'application  1.1    Le présent document décrit une méthode d'essai générale permettant de déterminer la température de fléchissement sous charge (contrainte de flexion sous mise en charge en trois points) des plastiques. Différents types d'éprouvettes et différentes charges constantes sont définis pour correspondre à des types de matériaux différents.
1.2    L'ISO 75-2 fournit des exigences particulières pour les plastiques (incluant les plastiques chargés et les plastiques renforcés de fibres, dans lesquels la longueur de fibre avant l'emploi est inférieure ou égale à 7,5 mm) et l'ébonite, et l'ISO 75-3 fournit des exigences particulières pour les stratifiés thermodurcissables à haute résistance et les plastiques renforcés de fibres longues, dans lesquels la longueur de fibre avant l'emploi est supérieure à 7,5 mm.
1.3    Les méthodes spécifiées permettent d'évaluer le comportement relatif sous charge des divers types de matériaux à température élevée, avec une élévation de la température à une vitesse spécifiée. Les résultats obtenus ne représentent pas nécessairement les températures maximales d'utilisation car, dans la pratique, des facteurs essentiels tels que le temps, les conditions de mise en charge et la contrainte superficielle nominale peuvent différer des conditions adoptées pour l'essai. Une comparabilité exacte des données ne peut être obtenue que pour des matériaux ayant le même module de flexion à température ambiante.
1.4    Les méthodes spécifient les dimensions recommandées pour les éprouvettes.
1.5    Les données obtenues en utilisant les méthodes d'essais décrites ne sont pas destinées à être utilisées pour prédire de véritables performances d'usage. Les données ne sont pas destinées à être utilisées pour les analyses de conception ou pour prévoir la résistance des matériaux à des températures élevées.
1.6    La présente méthode est communément connue sous le nom d'essai de déformation à chaud ou de fléchissement à chaud (HDT) bien qu'il n'existe pas de document officiel utilisant cette désignation.

Polimerni materiali - Ugotavljanje temperature upogiba pod obremenitvijo - 1. del: Splošna preskusna metoda (ISO 75-1:2020)

General Information

Status
Published
Publication Date
10-Mar-2020
Withdrawal Date
29-Sep-2020
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Mar-2020
Completion Date
11-Mar-2020

Relations

Buy Standard

Standard
EN ISO 75-1:2020
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 75-1:2019
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 75-1:2020
01-junij-2020
Nadomešča:
SIST EN ISO 75-1:2013
Polimerni materiali - Ugotavljanje temperature upogiba pod obremenitvijo - 1. del:
Splošna preskusna metoda (ISO 75-1:2020)
Plastics - Determination of temperature of deflection under load - Part 1: General test
method (ISO 75-1:2020)
Kunststoffe - Bestimmung der Wärmeformbeständigkeitstemperatur - Teil 1: Allgemeines
Prüfverfahren (ISO 75-1:2020)
Plastiques - Détermination de la température de fléchissement sous charge - Partie 1:
Méthode d'essai générale (ISO 75-1:2020)
Ta slovenski standard je istoveten z: EN ISO 75-1:2020
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 75-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 75-1:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 75-1:2020


EN ISO 75-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2020
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 75-1:2013
English Version

Plastics - Determination of temperature of deflection
under load - Part 1: General test method (ISO 75-1:2020)
Plastiques - Détermination de la température de Kunststoffe - Bestimmung der
fléchissement sous charge - Partie 1: Méthode d'essai Wärmeformbeständigkeitstemperatur - Teil 1:
générale (ISO 75-1:2020) Allgemeines Prüfverfahren (ISO 75-1:2020)
This European Standard was approved by CEN on 22 February 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 75-1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 75-1:2020
EN ISO 75-1:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 75-1:2020
EN ISO 75-1:2020 (E)
European foreword
This document (EN ISO 75-1:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 75-1:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 75-1:2020 has been approved by CEN as EN ISO 75-1:2020 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 75-1:2020

---------------------- Page: 6 ----------------------
SIST EN ISO 75-1:2020
INTERNATIONAL ISO
STANDARD 75-1
Fourth edition
2020-02
Plastics — Determination of
temperature of def
...

SLOVENSKI STANDARD
oSIST prEN ISO 75-1:2019
01-maj-2019
Polimerni materiali - Ugotavljanje temperature upogiba pod obremenitvijo - 1. del:
Splošna preskusna metoda (ISO/DIS 75-1:2019)
Plastics - Determination of temperature of deflection under load - Part 1: General test
method (ISO/DIS 75-1:2019)
Kunststoffe - Bestimmung der Wärmeformbeständigkeitstemperatur - Teil 1: Allgemeines
Prüfverfahren (ISO/DIS 75-1:2019)
Plastiques - Détermination de la température de fléchissement sous charge - Partie 1:
Méthode d'essai générale (ISO/DIS 75-1:2019)
Ta slovenski standard je istoveten z: prEN ISO 75-1:2019
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 75-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 75-1:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 75-1:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 75-1
ISO/TC 61/SC 2 Secretariat: KATS
Voting begins on: Voting terminates on:
2019-03-07 2019-05-30
Plastics — Determination of temperature of deflection
under load —
Part 1:
General test method
Plastiques — Détermination de la température de fléchissement sous charge —
Partie 1: Méthode d'essai générale
ICS: 83.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 75-1:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 75-1:2019
ISO/DIS 75-1:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 75-1:2019
ISO/DIS 75-1:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3  Terms and definitions . 2
4 Principle . 3
5 Apparatus . 3
5.1 Means of producing a flexural stress . 3
5.2 Heating equipment .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.