iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 17638:2009

(Main)

Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2003)

Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2003)

ISO 17638:2003 specifies techniques for detection of surface imperfections in welds in ferromagnetic materials, including the heat affected zones, by means of magnetic particle testing. The techniques are suitable for most welding processes and joint configurations.

Zerstörungsfreie Prüfung von Schweißverbindungen - Magnetpulverprüfung (ISO 17638:2003)

Diese Internationale Norm legt Techniken zum Nachweis von Unregelmäßigkeiten in der Oberfläche von ferromagnetischen Schweißnähten, einschließlich der Wärmeeinflusszonen, durch Magnetpulverprüfung fest. Diese Techniken sind für die meisten Schweißverfahren und Verbindungsarten geeignet. Variationen dieser grundlegenden Techniken mit höherer oder niedriger Prüfempfindlichkeit sind im Anhang A beschrieben.
Diese Internationale Norm legt keine Zulässigkeitsgrenzen für die Anzeigen fest. Weitere Informationen bezüglich Zulässigkeitsgrenzen für Anzeigen können entweder in EN 1291 oder in Produkt  oder Anwendungsnormen gefunden werden.

Contrôle non destructif des assemblages soudés - Contrôle par magnétoscopie (ISO 17638:2003)

L'ISO 17638:2003 spécifie les méthodes pour la détection par contrôle par magnétoscopie des défauts de surface des soudures de matériaux ferromagnétiques, y compris les zones affectées thermiquement, à l'aide de la méthode de magnétisation par passage de courant. Les techniques sont appropriées pour la plupart des procédés de soudage et des configurations d'assemblages.

Neporušitveno preskušanje zvarnih spojev - Preskušanje z magnetnimi delci (ISO 17638:2003)

Ta mednarodni standard določa tehnike za detekcijo površinskih nepravilnosti zvarnih spojev na feromagnetnih materialih, vključno s toplotno vplivanimi področji, z uporabo preskušanja z magnetnimi delci. Tehnike so primerne za večino varilnih postopkov in konfiguracij spojev. Spremembe osnovnih tehnik, ki omogočajo večjo ali manjšo občutljivost preskusa, so opisane v Dodatku A. Ta mednarodni standard ne določa stopenj sprejemljivosti indikacij. Dodatne informacije o stopnjah sprejemljivosti za indikacije so navedene v EN 1291 ali v standardih proizvoda ali uporabe.

General Information

Status
Withdrawn
Publication Date
10-Nov-2009
Withdrawal Date
15-Nov-2016
ICS
25.160.40 - Welded joints and welds
Technical Committee
CEN/TC 121 - Welding
Drafting Committee
CEN/TC 121/WG 21 - Testing of welds
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
16-Nov-2016
Directive
2009/105/EC - DIRECTIVE 2009/105/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 September 2009 relating to simple pressure vessels
2009/105//EC - DIRECTIVE 2009/105/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 September 2009 relating to simple pressure vessels
2014/29/EU - Directive 2014/29/EU of The European Parliament and of the Council of 26 February 2016 on the harmonisation of the laws of the Member States relating to the making available on the market of simple pressure vessels
87/404/EEC - Simple pressure vessels
Mandate
M/BC/CEN/89/2 - Standardization mandate to CEN concerning supporting standards in the context of pressure vessels
Ref Project
SIST EN ISO 17638:2010 - Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2003)

Relations

Replaces
EN 1290:1998 - Non-destructive examination of welds - Magnetic particle examination of welds
Effective Date
08-Jun-2022
Replaces
EN 1290:1998/A1:2002 - Non-destructive testing of welds - Magnetic particle testing of welds
Effective Date
14-Nov-2009
Replaces
EN 1290:1998/A2:2003 - Non-destructive testing of welds - Magnetic particle testing of welds
Effective Date
14-Nov-2009
Replaced By
EN ISO 17638:2016 - Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2016)
Effective Date
23-Nov-2016

Buy Standard

EN ISO 17638:2010EN ISO 17638:2010
PreviousNext
Standard
EN ISO 17638:2010
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17638:2010
01-april-2010
1DGRPHãþD
SIST EN 1290:1999
SIST EN 1290:1999/A1:2003
SIST EN 1290:1999/A2:2004
Neporušitveno preskušanje zvarnih spojev - Preskušanje z magnetnimi delci (ISO
17638:2003)
Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2003)
Zerstörungsfreie Prüfung von Schweißverbindungen - Magnetpulverprüfung (ISO
17638:2003)
Contrôle non destructif des assemblages soudés - Contrôle par magnétoscopie (ISO
17638:2003)
Ta slovenski standard je istoveten z: EN ISO 17638:2009
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 17638:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 17638:2010

---------------------- Page: 2 ----------------------

SIST EN ISO 17638:2010


EUROPEAN STANDARD
EN ISO 17638

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2009
ICS 25.160.40 Supersedes EN 1290:1998
English Version
Non-destructive testing of welds - Magnetic particle testing (ISO
17638:2003)
Contrôle non destructif des assemblages soudés - Contrôle Zerstörungsfreie Prüfung von Schweißverbindungen -
par magnétoscopie (ISO 17638:2003) Magnetpulverprüfung (ISO 17638:2003)
This European Standard was approved by CEN on 24 October 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17638:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 17638:2010
EN ISO 17638:2009 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 17638:2010
EN ISO 17638:2009 (E)
Foreword
The text of ISO 17638:2003 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
17638:2009 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the
latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1290:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 17638:2003 has been approved by CEN as a EN ISO 17638:2009 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 17638:2010

---------------------- Page: 6 ----------------------

SIST EN ISO 17638:2010


INTERNATIONAL ISO
STANDARD 17638
First edition
2003-08-01


Non-destructive testing of welds —
Magnetic particle testing
Contrôle non destructif des assemblages soudés — Contrôle par
magnétoscopie




Reference number
ISO 17638:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 9692-2:2024(Main)
Welding and allied processes - Joint preparation - Part 2: Submerged arc welding of steels (ISO 9692-2:2024)
oSIST prEN ISO 9692-2:2023

This document applies to types of joint preparation for submerged arc welding with one wire electrode (process 121 according to ISO 4063) on steel.
This document covers only the welding positions PA and PB according to ISO 6947. If PC is used, special preparation is necessary.
This document applies to fully penetrated welds. For partly penetrated welds, types of joint preparation, shapes and dimensions can differ from the listed proposals if they are specified in the relevant application standard or agreed by the parties concerned.

  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5817:2023(Main)
Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2023)
SIST EN ISO 5817:2023

This document specifies quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds.
Quality levels for beam-welded joints in steel are presented in ISO 13919-1.
Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld.
Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex B.
The quality levels refer to production and good workmanship.
This document is applicable to:
a)       non-alloy and alloy steels;
b)       nickel and nickel alloys;
c)        titanium and titanium alloys;
d)       manual, mechanized and automatic welding;
e)       all welding positions;
f)         all types of welds, e.g. butt welds, fillet welds and branch connections;
g)       the following welding processes and their sub-processes, as defined in ISO 4063:
—     11 metal arc welding without gas protection;
—     12 submerged arc welding;
—     13 gas-shielded metal arc welding;
—     14 gas-shielded arc welding with non-consumable tungsten electrode;
—     15 plasma arc welding;
—     31 oxyfuel gas welding (for steel only).
Metallurgical aspects, such as grain size and hardness, are not covered by this document.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5173:2023(Main)
Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2023)
SIST EN ISO 5173:2023

This document specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to reveal imperfections on or near the surface of the test specimen which is under tension during bend testing and/or assess ductility. It also gives the dimensions of the test specimen.
In addition, this document specifies methods to be used instead of transverse bend tests with a former for welded joints when base materials, heat affected zones and/or weld metal have a significant difference in their physical and mechanical properties in relation to bending.
This document applies to metallic materials in all forms of product with welded joints made by any welding process.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4761:2022(Main)
Non-destructive testing of welds - Phased array ultrasonic testing (UT-PA) for thin-walled steel components - Acceptance levels (ISO 4761:2022)
SIST EN ISO 4761:2023

This document specifies acceptance levels for the phased array ultrasonic testing technique (UT-PA) of full-penetration welds in low-alloy and/or fine-grained steels in the wall thickness range from 3,2 mm to 8 mm which correspond to the quality levels of ISO 5817.
These acceptance levels are applicable to indications detected according to ISO 20601.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10447:2022(Main)
Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2022)
SIST EN ISO 10447:2023

This document specifies the procedures and recommended tooling to be used for peel and chisel testing of resistance spot and embossed projection welds. This document applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm.
The aim of these tests is to determine:
—    weld size and failure mode when welds are destructively tested;
—    verification of welds by non-destructive chisel tests.
NOTE      The preferred method of peel testing seam welds (mechanized peel testing) is covered in ISO 14270.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17636-2:2022(Main)
Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2022, Corrected version 2023-02)
SIST EN ISO 17636-2:2023

This document specifies techniques of digital radiography with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
This document applies to the digital radiographic testing of fusion welded joints in metallic materials. It applies to the joints of plates and pipes. Besides its conventional meaning, “pipe”, as used in this document, covers other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels.
This document specifies the requirements for digital radiographic X- and gamma-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDAs) of the welded joints of metallic plates and tubes for the detection of imperfections. It includes manual and automated inspection with DDAs.
Digital detectors provide a digital grey value image which can be viewed and evaluated using a computer (Annex E). This document specifies the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important, but are not the main focus of this document. The procedure specified in this document provides the minimum requirements for radiographic practice which permits exposure and acquisition of digital radiographs with equivalent sensitivity for the detection of imperfections as film radiography (specified in ISO 17636-1).
This document does not specify acceptance levels for any of the indications found on the digital radiographs. ISO 10675 provides information on acceptance levels for weld inspection.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17636-1:2022(Main)
Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2022)
SIST EN ISO 17636-1:2023

This document specifies techniques of radiographic testing of fusion-welded joints in metallic materials using industrial radiographic film techniques with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
It applies to the joints of plates and pipes in metallic materials. Besides its conventional meaning, “pipe” as used in this document covers other cylindrical bodies, such as tubes, penstocks, boiler drums and pressure vessels.
This document does not specify acceptance levels for any of the indications found on the radiographs. The ISO 10675 series provides information on acceptance levels for weld evaluation.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4136:2022(Main)
Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2022)
SIST EN ISO 4136:2022

This document specifies the sizes of test specimen and the procedure for carrying out transverse tensile tests in order to determine the tensile strength and the location of fracture of a welded butt joint.
This document applies to metallic materials in all forms of product with joints made by any welded butt joint.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9016:2022(Main)
Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination (ISO 9016:2022)
SIST EN ISO 9016:2022

This document specifies the method to be used when describing test specimen location and notch orientation for the testing and reporting of impact tests on welded butt joints.
This document applies to impact tests on metallic materials in all forms of product made by any fusion and pressure welding process.
It is used in addition to the ISO 148 series and includes test specimen denomination and additional reporting requirements.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17639:2022(Main)
Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2022)
SIST EN ISO 17639:2022

This document gives recommendations for specimen preparation, test procedures and their main objectives for macroscopic and microscopic examination.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day