Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zones are grouped together with location or orientation constraints, through the use of the CZ, CZR or SIM modifiers.
This document does not cover the use of the pattern specifications when the least and maximum material requirement is applied (see ISO 2692).
This document does not cover the establishment of common datum (see ISO 5459) based on pattern features.

Geometrische Produktspezifikationen (GPS) - Geometrische Tolerierung - Elementgruppen und kombinierte geometrische Spezifikation (ISO 5458:2018)

Dieses Dokument legt ergänzende Regeln zu ISO 1101 fest, die auf Elementgruppenspezifikationen anzuwenden sind, und definiert Regeln zur Kombination einzelner Spezifikationen für geometrische Spezifikationen, z. B. durch Verwenden der Symbole POSITION, SYMMETRIE, LINIENPROFIL und FLÄCHENPROFIL sowie GERADHEIT (wenn die tolerierten Geometrieelemente nominal koaxial sind) und EBENHEIT (wenn die tolerierten Geometrieelemente nominal koplanar sind) wie in Anhang C angegeben.
Diese Regeln gelten, wenn eine Reihe von Toleranzzonen durch Verwenden der CZ-, CZR- oder SIM-Modifikatoren mit Nebenbedingungen für Ort oder Richtung zusammengefasst werden.
Dieses Dokument behandelt nicht das Anwenden der Elementgruppenspezifikationen, wenn die Minimum- und die Maximum-Material-Bedingung angewendet wird (siehe ISO 2692).
Dieses Dokument behandelt nicht das Festlegen eines gemeinsamen Bezugs (siehe ISO 5459) basierend auf Gruppenelementen.

Spécification géométrique des produits (GPS) - Tolérancement géométrique - Spécification géométrique de groupes d'éléments et spécification géométrique combinée (ISO 5458:2018)

Le présent document établit des règles complémentaires de celles de l'ISO 1101 à appliquer aux spécifications de groupes d'éléments et définit des règles pour combiner des spécifications individuelles, pour les spécifications géométriques, par exemple en utilisant les symboles de LOCALISATION, SYMÉTRIE, PROFIL DE LIGNE et PROFIL DE SURFACE, ainsi que les symboles de RECTITUDE (dans le cas où les éléments tolérancés sont nominalement coaxiaux) et de PLANÉITÉ (dans le cas où les éléments tolérancés sont nominalement coplanaires) comme listés en Annexe C.
Ces règles s'appliquent lorsqu'un ensemble de zones de tolérances sont regroupées ensemble avec des contraintes de position ou d'orientation, en utilisant les modificateurs CZ, CZR ou SIM.
Le présent document ne couvre pas l'utilisation des spécifications de groupes d'éléments lorsque l'exigence du minimum et du maximum de matière s'applique (voir l'ISO 2692).
Le présent document ne couvre pas non plus l'établissement de référence spécifiée commune (voir l'ISO 5459) basée sur des éléments de groupe d'éléments.

Specifikacija geometrijskih veličin izdelka (GPS) - Geometrijsko toleriranje - Vzorec in kombinirane geometrijske specifikacije (ISO 5458:2018)

Ta dokument določa dopolnilna pravila k standardu ISO 1101, ki se uporabljajo za specifikacije vzorca in opredeljuje pravila za združevanje posameznih specifikacij, npr. z uporabo simbolov POLOŽAJ, SIMETRIJA, LINIJSKI PROFIL in POVRŠINSKI PROFIL ter RAVNOST (v primeru, kjer so tolerančne značilnosti nominalno koaksialne) in PLOŠČATOST (v primeru, kjer so tolerančne značilnosti nominalno koplanarne), kakor je navedeno v dodatku C.
Ta pravila se uporabljajo, ko se nabor tolerančnih območij združi z lokacijskimi ali usmeritvenimi omejitvami z uporabo modifikatorjev CZ, CZR ali SIM.
Ta dokument ne zajema uporabe specifikacije vzorca, ko se uporablja zahteva po minimalnem ali maksimalnem materialu (glej ISO 2692).
Ta dokument ne zajema določanja skupnih referenc (glej ISO 5459) na podlagi značilnosti
vzorca.

General Information

Status
Published
Publication Date
05-Jun-2018
Withdrawal Date
30-Dec-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
06-Jun-2018
Completion Date
06-Jun-2018

Relations

Buy Standard

Standard
EN ISO 5458:2018
English language
52 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 5458:2015 - BARVE
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5458:2018
01-september-2018
1DGRPHãþD
SIST EN ISO 5458:2000
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 *HRPHWULMVNRWROHULUDQMH
9]RUHFLQNRPELQLUDQHJHRPHWULMVNHVSHFLILNDFLMH ,62
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and
combined geometrical specification (ISO 5458:2018)
Geometrische Produktspezifikation (GPS) - Form und Lagetolerierung - Positions- und
Mustertolerierung (ISO 5458:2018)
Spécification géométrique des produits (GPS) - Tolérancement géométrique -
Spécification géométrique de groupes d'éléments et spécification géométrique combinée
(ISO 5458:2018)
Ta slovenski standard je istoveten z: EN ISO 5458:2018
ICS:
01.100.01 7HKQLþQRULVDQMHQDVSORãQR Technical drawings in
general
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
SIST EN ISO 5458:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5458:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 5458:2018


EN ISO 5458
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2018
EUROPÄISCHE NORM
ICS 17.040.10 Supersedes EN ISO 5458:1998
English Version

Geometrical product specifications (GPS) - Geometrical
tolerancing - Pattern and combined geometrical
specification (ISO 5458:2018)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) - Form und
Tolérancement géométrique - Spécification Lagetolerierung - Positions- und Mustertolerierung
géométrique de groupes d'éléments et spécification (ISO 5458:2018)
géométrique combinée (ISO 5458:2018)
This European Standard was approved by CEN on 25 February 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5458:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5458:2018
EN ISO 5458:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 5458:2018
EN ISO 5458:2018 (E)
European foreword
This document (EN ISO 5458:2018) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2018, and conflicting national standards
shall be withdrawn at the latest by December 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5458:1998.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serb
...

SLOVENSKI STANDARD
oSIST prEN ISO 5458:2015
01-september-2015
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 7ROHULUDQMHJHRPHWULMH
7ROHULUDQMHSR]LFLM ,62',6
Geometrical Product Specifications (GPS) - Geometrical tolerancing - Positional
tolerancing (ISO/DIS 5458:2015)
Geometrische Produktspezifikation (GPS) - Form- und Lagetolerierung -
Positionstolerierung (ISO/DIS 5458:2015)
Spécification géométrique des produits (GPS) - Tolérancement géométrique -
Tolérancement de position et de motif (ISO/DIS 5458:2015)
Ta slovenski standard je istoveten z: prEN ISO 5458 rev
ICS:
01.100.01 7HKQLþQRULVDQMHQDVSORãQR Technical drawings in
general
17.040.30 Merila Measuring instruments
oSIST prEN ISO 5458:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 5458:2015

---------------------- Page: 2 ----------------------
oSIST prEN ISO 5458:2015

DRAFT INTERNATIONAL STANDARD ISO/DIS 5458
ISO/TC 213 Secretariat: DS
Voting begins on Voting terminates on

2015-06-11 2015-09-11
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION    МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ    ORGANISATION INTERNATIONALE DE NORMALISATION


Geometrical Product Specifications (GPS) — Geometrical
tolerancing — Positional and pattern tolerancing
Spécification géométrique des produits (GPS) — Tolérancement géométrique — Tolérancement de position
et de motif

ICS 17.040.10





ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.

To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.



THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©  International Organization for Standardization, 2015

---------------------- Page: 3 ----------------------
oSIST prEN ISO 5458:2015
ISO/DIS 5458

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any
means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission.
Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 5458:2015
ISO/DIS 5458(E)
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Specification modifiers and symbols .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.