Rough-terrain trucks - Safety requirements and verification - Part 5: Attachment interface

This document specifies requirements for the truck side of the attachment interface of rough-terrain non-slewing and slewing variable reach trucks (hereafter referred to as "trucks") dealt with in EN 1459-1:2017+A1:2020, EN 1459-2:2015+A1:2018 and EN 1459-4:2020.
This document covers the interface for the attachments fitted to the telescopic boom carriage or mounted on the forks when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. This document does not cover:
- interface for interchangeable equipment designed for lifting person(s) (covered by EN 1459-3:2015);
- interface for equipment for container handling (e.g. spreader);
- interface for equipment permanently installed on the machine and not intended to be removed by the user.
NOTE In this case, equipment becomes part of the truck.
This document does not give requirements for the completed assembly of a truck fitted with an attachment. This document does not address risks to parts of the truck other than the interface with the attachment.
This document is not applicable to interfaces manufactured before the date of its publication.

Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil 5: Zugehörige Schnittstellen

Dieses Dokument legt Anforderungen an die Schnittstellen für Anbaugeräte auf der Seite des Staplers für geländegängige, schwenkbare und nicht schwenkbare Stapler mit veränderlicher Reichweite (im Folgenden als „Stapler“ bezeichnet) fest, die in EN 1459 1:2017+A1:2020, EN 1459 2:2015+A1:2018 und EN 1459 4:2020 behandelt werden.
Dieses Dokument behandelt die Schnittstellen für am Gabelträger mit Teleskopausleger befestigte oder an den Gabeln angebrachte Anbaugeräte, wenn diese wie vom Hersteller vorgesehen und unter Bedingungen von durch den Hersteller vernünftigerweise vorhersehbaren Fehlanwendungen verwendet werden. Dieses Dokument behandelt nicht:
- Schnittstellen für auswechselbare Ausrüstungen, die zum Heben von Personen dienen (abgedeckt durch EN 1459 3:2015);
- Schnittstelle für Ausrüstung für die Handhabung von Containern (z. B. Spreizer);
- Schnittstellen für Ausrüstungen, die permanent an der Maschine montiert sind und nicht zur Entfernung durch den Anwender vorgesehen sind;
ANMERKUNG In diesem Falle wird die Ausrüstung ein Teil des Staplers.
Dieses Dokument legt keine Anforderungen an die fertiggestellte Gesamtheit eines mit einem Anbaugerät ausgestatteten Staplers fest. Dieses Dokument befasst sich neben den Risiken von Teilen der Schnittstelle mit dem Anbaugerät mit keinen anderen Teilen des Staplers.
Dieses Dokument gilt nicht für Schnittstellen, die vor dem Veröffentlichungsdatum dieses Dokuments hergestellt wurden.

Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 5 : Interface de l'accessoire

Le présent document spécifie les prescriptions pour l'interface de l'accessoire côté chariot des chariots tout-terrain à portée variable rotatifs ou non (ci-après désignés « chariots ») traités dans les EN 1459-1:2017+A1:2020, EN 1459-2:2015+A1:2018 et EN 1459-4:2020.
Le présent document couvre l'interface pour les accessoires montés sur le tablier de la flèche télescopique ou montés sur les fourches lorsqu'elle est utilisée comme prévu et dans des conditions de mauvaise utilisation qui sont raisonnablement prévisibles par le fabricant. Le présent document ne couvre pas :
- l'interface pour l'équipement interchangeable conçu pour le levage d'une ou plusieurs personnes (couvert par l'EN 1459-3:2015) ;
- l'interface pour l'équipement pour la manutention de conteneur (par exemple, palonnier) ;
- l'interface pour l'équipement monté de façon permanente sur la machine et qui n'est pas destiné à être retiré par l'utilisateur ;
NOTE Dans ce cas, l'équipement devient une partie du chariot.
Le présent document ne donne pas de prescriptions pour l'assemblage complet d'un chariot muni d'un accessoire. Le présent document ne traite pas les risques liés à des parties du chariot autres que l'interface avec l'accessoire.
Le présent document n'est pas applicable aux interfaces fabriquées avant la date de sa publication.

Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje - 5. del: Pripadajoči vmesniki

General Information

Status
Published
Publication Date
22-Dec-2020
Withdrawal Date
29-Jun-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
23-Dec-2020
Due Date
28-Aug-2021
Completion Date
23-Dec-2020

Relations

Buy Standard

Standard
EN 1459-5:2021
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 1459-5:2019
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1459-5:2021
01-april-2021
Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje - 5.
del: Pripadajoči vmesniki
Rough-terrain trucks - Safety requirements and verification - Part 5: Attachment interface
Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil
5: Zugehörige Schnittstellen
Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 5 : Interface de
l'accessoire
Ta slovenski standard je istoveten z: EN 1459-5:2020
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 1459-5:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1459-5:2021

---------------------- Page: 2 ----------------------
SIST EN 1459-5:2021


EN 1459-5
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2020
EUROPÄISCHE NORM
ICS 53.060
English Version

Rough-terrain trucks - Safety requirements and
verification - Part 5: Attachment interface
Chariots tout-terrain - Prescriptions de sécurité et Geländegängige Stapler - Sicherheitstechnische
vérification - Partie 5 : Interface de l'accessoire Anforderungen und Verifizierung - Teil 5: Zugehörige
Schnittstellen
This European Standard was approved by CEN on 23 November 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1459-5:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 1459-5:2021
EN 1459-5:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Requirements . 8
4.1 Manual connection/disconnection . 8
4.2 Unintentional detachment . 8
4.3 Unintended movement of the attachment . 8
4.4 Load-clamping attachment interface . 9
4.5 Interface hydraulic system . 9
4.6 Design . 9
4.7 Mechanical connection of the attachment to the carriage . 9
4.7.1 General . 9
4.7.2 Fastening and locking . 9
4.7.3 Control
...

SLOVENSKI STANDARD
oSIST prEN 1459-5:2019
01-september-2019
Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje - 5.
del: Pripadajoči vmesniki
Rough-terrain trucks - Safety requirements and verification - Part 5: Attachment interface
Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil
5: Zugehörige Schnittstellen
Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 5 : Interface de
l'accessoire
Ta slovenski standard je istoveten z: prEN 1459-5
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN 1459-5:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1459-5:2019

---------------------- Page: 2 ----------------------
oSIST prEN 1459-5:2019


DRAFT
EUROPEAN STANDARD
prEN 1459-5
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2019
ICS 53.060
English Version

Rough-terrain trucks - Safety requirements and
verification - Part 5: Attachment interface
Chariots tout-terrain - Prescriptions de sécurité et Geländegängige Stapler - Sicherheitstechnische
vérification - Partie 5 : Interface de l'accessoire Anforderungen und Verifizierung - Teil 5: Zugehörige
Schnittstellen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 150.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1459-5:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1459-5:2019
prEN 1459-5:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Requirements . 6
4.1 Manual connection/disconnection . 6
4.2 Unintentional detachment . 7
4.3 Unintended movement of the attachment . 7
4.4 Load-clamping attachment interface . 7
4.5 Interface hydraulic system .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.