Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes - Periodic inspection and testing (ISO 18119:2018)

This document specifies the requirements for periodic inspection and testing to verify the integrity of cylinders and tubes to be re-introduced into service for a further period of time.
This document is applicable to seamless steel and seamless aluminium-alloy transportable gas cylinders (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l and to seamless steel and seamless aluminium-alloy transportable gas tubes (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity greater than 150 l. It also applies, as far as practical, to cylinders of less than 0,5 l water capacity.
This document does not apply to the periodic inspection and maintenance of acetylene cylinders or to the periodic inspection and testing of composite cylinders.
NOTE       Unless noted by exception, the use of the word "cylinder" in this document refers to both cylinders and tubes.

Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)

Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans soudure - Contrôles et essais périodiques (ISO 18119:2018)

Le présent document spécifie les exigences en matière de contrôles et d'essais périodiques destinés à vérifier l'intégrité des bouteilles et tubes avant leur remise en service pour une nouvelle période d'utilisation.
Le présent document est applicable aux bouteilles à gaz transportables en acier et en alliages d'aluminium sans soudure (seules ou comprenant un cadre) prévues pour des gaz comprimés et liquéfiés sous pression, d'une contenance en eau de 0,5 l à 150 l, ainsi qu'aux tubes à gaz transportables, en acier et en alliages d'aluminium sans soudure (seuls ou comprenant un cadre) prévus pour des gaz comprimés et liquéfiés sous pression, d'une contenance en eau supérieure à 150 l. Dans la mesure du possible, il s'applique également aux bouteilles d'une contenance en eau inférieure à 0,5 l.
Le présent document ne s'applique pas au contrôle et à la maintenance périodiques des bouteilles d'acétylène ni aux contrôles et essais périodiques des bouteilles en matériaux composites.
NOTE       Sauf mention contraire, le terme «bouteille» désigne aussi bien une bouteille qu'un tube dans le présent document.

Plinske jeklenke - Plinske jeklenke in velike jeklenke iz celega iz jekla in aluminijevih zlitin - Periodični pregled in preskušanje (ISO 18119:2018)

Ta mednarodni standard se uporablja za prenosne nevarjene plinske jeklenke ter velike jeklenke iz jekla in aluminijevih zlitin (posamične ali v sklopu) za stisnjene in utekočinjene pline pod tlakom s prostornino vode od 0,5 l do 150 l. Uporablja se tudi za jeklenke s prostornino vode manj kot 0,5 l in več kot 150 l, če je to smotrno. Ta mednarodni standard določa zahteve za redne preglede in preskuse za namene preverjanja celovitosti tovrstnih plinskih jeklenk, predvidene za nadaljnjo vnovično uporabo. Ta mednarodni standard se ne uporablja za redne preglede in vzdrževanje jeklenk z acetilenom ali redne preglede in preskušanje kompozitnih jeklenk.

General Information

Status
Published
Publication Date
23-Oct-2018
Withdrawal Date
29-Apr-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Oct-2018
Completion Date
24-Oct-2018

Relations

Buy Standard

Standard
EN ISO 18119:2019
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 18119:2019 (EN)
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 18119:2019 (EN)
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 18119:2019 (DE)
German language
65 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 18119:2019 (DE)
German language
65 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 18119:2015
English language
53 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 18119:2019
01-januar-2019
3OLQVNHMHNOHQNH1HYDUMHQHSOLQVNHMHNOHQNHLQYHOLNHMHNOHQNHL]MHNODLQ
DOXPLQLMHYLK]OLWLQ3HULRGLþQLSUHJOHGLQSUHVNXãDQMH ,62
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO 18119:2018)
Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans
soudure - Contrôles et essais périodiques (ISO 18119:2018)
Ta slovenski standard je istoveten z: EN ISO 18119:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN ISO 18119:2019 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18119:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 18119:2019


EN ISO 18119
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 23.020.35
English Version

Gas cylinders - Seamless steel and seamless aluminium-
alloy gas cylinders and tubes - Periodic inspection and
testing (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en Gasflaschen - Nahtlose Gasflaschen und Großflaschen
alliages d'aluminium, sans soudure - Contrôles et aus Stahl und Aluminiumlegierungen -
essais périodiques (ISO 18119:2018) Wiederkehrende Inspektion und Prüfung (ISO
18119:2018)
This European Standard was approved by CEN on 17 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18119:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
European foreword
This document (EN ISO 18119:2018) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18119:2018 has been approved by CEN as EN ISO 18119:2018 without any m
...

SLOVENSKI STANDARD
SIST EN ISO 18119:2019
01-januar-2019
Plinske jeklenke - Nevarjene plinske jeklenke in velike jeklenke iz jekla in
aluminijevih zlitin - Periodični pregled in preskušanje (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO 18119:2018)
Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans
soudure - Contrôles et essais périodiques (ISO 18119:2018)
Ta slovenski standard je istoveten z: EN ISO 18119:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN ISO 18119:2019 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 18119:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 18119:2019


EN ISO 18119
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 23.020.35
English Version

Gas cylinders - Seamless steel and seamless aluminium-
alloy gas cylinders and tubes - Periodic inspection and
testing (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en Gasflaschen - Nahtlose Gasflaschen und Großflaschen
alliages d'aluminium, sans soudure - Contrôles et aus Stahl und Aluminiumlegierungen -
essais périodiques (ISO 18119:2018) Wiederkehrende Inspektion und Prüfung (ISO
18119:2018)
This European Standard was approved by CEN on 17 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18119:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
European foreword
This document (EN ISO 18119:2018) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18119:2018 has been approved by CEN as EN ISO 18119:2018 without any modific
...

SLOVENSKI STANDARD
SIST EN ISO 18119:2019
01-januar-2019
Plinske jeklenke - Plinske jeklenke in velike jeklenke iz celega iz jekla in
aluminijevih zlitin - Periodični pregled in preskušanje (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO 18119:2018)
Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans
soudure - Contrôles et essais périodiques (ISO 18119:2018)
Ta slovenski standard je istoveten z: EN ISO 18119:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN ISO 18119:2019 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 18119:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 18119:2019


EN ISO 18119
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 23.020.35
English Version

Gas cylinders - Seamless steel and seamless aluminium-
alloy gas cylinders and tubes - Periodic inspection and
testing (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en Gasflaschen - Nahtlose Gasflaschen und Großflaschen
alliages d'aluminium, sans soudure - Contrôles et aus Stahl und Aluminiumlegierungen -
essais périodiques (ISO 18119:2018) Wiederkehrende Inspektion und Prüfung (ISO
18119:2018)
This European Standard was approved by CEN on 17 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18119:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (E)
European foreword
This document (EN ISO 18119:2018) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18119:2018 has been approved by CEN as EN ISO 18119:2018 without any modific
...

SLOVENSKI STANDARD
SIST EN ISO 18119:2019
01-januar-2019
Plinske jeklenke - Nevarjene plinske jeklenke in velike jeklenke iz jekla in
aluminijevih zlitin - Periodični pregled in preskušanje (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO 18119:2018)
Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans
soudure - Contrôles et essais périodiques (ISO 18119:2018)
Ta slovenski standard je istoveten z: EN ISO 18119:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN ISO 18119:2019 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 18119:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 18119:2019


EN ISO 18119
EUROPÄISCHE NORM

EUROPEAN STANDARD

Oktober 2018
NORME EUROPÉENNE
ICS 23.020.35
Deutsche Fassung

Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus
Stahl und Aluminiumlegierungen - Wiederkehrende
Inspektion und Prüfung (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium- Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en
alloy gas cylinders and tubes - Periodic inspection and alliages d'aluminium, sans soudure - Contrôles et essais
testing (ISO 18119:2018) périodiques (ISO 18119:2018)
Diese Europäische Norm wurde vom CEN am 17. Mai 2018 angenommen.

Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter
denen dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist. Auf dem letzten Stand
befindliche Listen dieser nationalen Normen mit ihren bibliographischen Angaben sind beim CEN-CENELEC-Management-
Zentrum oder bei jedem CEN-Mitglied auf Anfrage erhältlich.

Diese Europäische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Französisch). Eine Fassung in einer anderen
Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem
Management-Zentrum mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen
jugoslawischen Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland,
Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz,
Serbien, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und
Zypern.





EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Rue de la Science 23, B-1040 Brüssel
© 2018 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. EN ISO 18119:2018 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN
vorbehalten.

---------------------- Page: 3 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (D)
Inhalt
Seite
Europäisches Vorwort . 6
Vorwort . 7
Einleitung . 8
1 Anwendungsbereich . 9
2 Normative Verweisungen . 9
3 Begriffe . 10
4 Abkürzungen und Symbole . 11
5 Zeitabstände zwischen den wiederkehrenden Inspektionen und Prüfungen . 11
6 Liste der Verfahren für wiederkehrende Inspektionen und Prüfungen . 12
7 Identifizierung der Gasflasche und Vorbereitung für Inspektion
...

SLOVENSKI STANDARD
SIST EN ISO 18119:2019
01-januar-2019
Plinske jeklenke - Plinske jeklenke in velike jeklenke iz celega iz jekla in
aluminijevih zlitin - Periodični pregled in preskušanje (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO 18119:2018)
Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO 18119:2018)
Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en alliages d'aluminium, sans
soudure - Contrôles et essais périodiques (ISO 18119:2018)
Ta slovenski standard je istoveten z: EN ISO 18119:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
SIST EN ISO 18119:2019 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 18119:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 18119:2019


EN ISO 18119
EUROPÄISCHE NORM

EUROPEAN STANDARD

Oktober 2018
NORME EUROPÉENNE
ICS 23.020.35
Deutsche Fassung

Gasflaschen - Nahtlose Gasflaschen und Großflaschen aus
Stahl und Aluminiumlegierungen - Wiederkehrende
Inspektion und Prüfung (ISO 18119:2018)
Gas cylinders - Seamless steel and seamless aluminium- Bouteilles à gaz - Bouteilles et tubes à gaz en acier et en
alloy gas cylinders and tubes - Periodic inspection and alliages d'aluminium, sans soudure - Contrôles et essais
testing (ISO 18119:2018) périodiques (ISO 18119:2018)
Diese Europäische Norm wurde vom CEN am 17. Mai 2018 angenommen.

Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter
denen dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist. Auf dem letzten Stand
befindliche Listen dieser nationalen Normen mit ihren bibliographischen Angaben sind beim CEN-CENELEC-Management-
Zentrum oder bei jedem CEN-Mitglied auf Anfrage erhältlich.

Diese Europäische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Französisch). Eine Fassung in einer anderen
Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem
Management-Zentrum mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen
jugoslawischen Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland,
Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz,
Serbien, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und
Zypern.





EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Rue de la Science 23, B-1040 Brüssel
© 2018 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. EN ISO 18119:2018 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN
vorbehalten.

---------------------- Page: 3 ----------------------
SIST EN ISO 18119:2019
EN ISO 18119:2018 (D)
Inhalt
Seite
Europäisches Vorwort . 6
Vorwort . 7
Einleitung . 8
1 Anwendungsbereich . 9
2 Normative Verweisungen . 9
3 Begriffe . 10
4 Abkürzungen und Symbole . 11
5 Zeitabstände zwischen den wiederkehrenden Inspektionen und Prüfungen . 11
6 Liste der Verfahren für wiederkehrende Inspektionen und Prüfungen . 12
7 Identifizierung der Gasflasche und Vorbereitung für Inspektion
...

SLOVENSKI STANDARD
oSIST prEN ISO 18119:2015
01-september-2015
3OLQVNHMHNOHQNH1HYDUMHQHMHNOHQHLQDOXPLQLMHYH]OLWLQHSOLQVNLKMHNOHQNLQFHYL
3HULRGLþQLSUHJOHGLQSUHVNXãDQMH ,62',6
Gas cylinders - Seamless steel and seamless aluminium-alloy gas cylinders and tubes -
Periodic inspection and testing (ISO/DIS 18119:2015)
Gasflaschen - Nahtlose Gasflaschenund Großflaschen aus Stahl und
Aluminiumlegierungen - Wiederkehrende Inspektion und Prüfung (ISO/DIS 18119:2015)
Bouteilles à gaz - Bouteilles à gaz en acier et en alliages d'aluminium, sans soudure -
Contrôles et essais périodiques (ISO/DIS 18119:2015)
Ta slovenski standard je istoveten z: prEN ISO 18119
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
oSIST prEN ISO 18119:2015 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 18119:2015

---------------------- Page: 2 ----------------------
oSIST prEN ISO 18119:2015
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18119
ISO/TC 58/SC 4 Secretariat: ANSI
Voting begins on: Voting terminates on:
2015-07-02 2015-10-02
Gas cylinders — Seamless steel and seamless
aluminium-alloy gas cylinders and tubes --- Periodic
inspection and testing
Bouteilles à gaz — Bouteilles à gaz en acier et en alliages d’aluminium, sans soudure — Contrôles et
essais périodiques
ICS: 23.020.30
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18119:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 3 ----------------------
oSIST prEN ISO 18119:2015
ISO/DIS 18119:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 18119:2015
ISO/DIS 18119
Contents Page
Foreword . v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols . 3
5 Intervals between periodic inspections and tests . 3
6 List of procedures for periodic inspections and tests . 4
7 Identif
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.