EN 1279-4:2018
(Main)Glass in Building - Insulating Glass Units - Part 4: Methods of test for the physical attributes of edge seal components and inserts
Glass in Building - Insulating Glass Units - Part 4: Methods of test for the physical attributes of edge seal components and inserts
This document specifies the requirements and describes the test methods for edge seal components and inserts. This includes the identification, the determination of physical attributes and the evaluation of characteristics for use in substitution rules in accordance with EN 1279 1:2018.
For the purpose to demonstrate that edge seal components will allow the insulating glass unit to conform to the requirements given in EN 1279 1:2018, Clause 6, EN 1279 2:2018 and EN 1279 3:2018 also apply.
Glas im Bauwesen - Mehrscheiben-Isolierglas - Teil 4: Verfahren zur Prüfung der physikalischen Eigenschaften der Komponenten des Randverbundes und der Einbauten
Diese Europäische Norm legt die Anforderungen an die Komponenten des Randverbunds und Einbauten fest und beschreibt ihre Prüfverfahren. Dies schließt die Identifizierung, die Bestimmung der physikalischen Merkmale und die Bewertung der Eigenschaften zur Anwendung der Austauschregeln in Übereinstimmung mit EN 1279-1:2018 ein.
Um nachzuweisen, dass die Komponenten des Randverbundes dazu geeignet sind, die Übereinstimmung des damit gefertigten Mehrscheiben-Isolierglases (MIG) mit den Anforderungen nach EN 1279-1:2018, Abschnitt 6, zu ermöglichen, sind EN 1279-2:2018 und EN 1279-3:2018 ebenfalls anzuwenden.
Verre dans la construction - Vitrage isolant - Partie 4: Méthodes d'essai des propriétés physiques des composants et inserts
Steklo v gradbeništvu - Izolacijsko steklo - 4. del: Preskusne metode za fizikalne lastnosti komponent robnega tesnjenja in vgrajenih delov
Ta evropski standard določa zahteve in preskusne metode za robno tesnjenje in vgrajene dele. To zajema identifikacijo, določanje fizičnih lastnosti in oceno lastnosti za uporabo pri pravilih o zamenjavi v skladu s standardom prEN 1279-1:2015.
Za dokazovanje, da komponente za robno tesnjenje omogočajo izolacijskemu steklu skladnost z zahtevami, opredeljenimi v točki 6 standarda prEN 1279-1:2015, se uporabljata tudi standarda prEN 1279-2:2015 in prEN 1279-3:2015.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Steklo v gradbeništvu - Izolacijsko steklo - 4. del: Preskusne metode za fizikalne lastnosti komponent robnega tesnjenja in vgrajenih delovGlas im Bauwesen - Mehrscheiben-Isolierglas - Teil 4: Verfahren zur Prüfung der physikalischen Eigenschaften der Komponenten des Randverbundes und der EinbautenVerre dans la construction - Vitrage isolant préfabriqué scellé - Partie 4 : Méthodes d'essai des propriétés physiques des composants et insertsGlass in Building - Insulating Glass Units - Part 4: Methods of test for the physical attributes of edge seal components and inserts81.040.20Steklo v gradbeništvuGlass in buildingICS:Ta slovenski standard je istoveten z:EN 1279-4:2018SIST EN 1279-4:2018en,fr,de01-oktober-2018SIST EN 1279-4:2018SLOVENSKI
STANDARDSIST EN 1279-4:20041DGRPHãþD
SIST EN 1279-4:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1279-4
July
t r s z ICS
z sä r v rä t r Supersedes EN
s t y {æ vã t r r tEnglish Version
Glass in Building æ Insulating Glass Units æ Part
vã Methods of test for the physical attributes of edge seal components and inserts Verre dans la construction æ Vitrage isolant préfabriqué scellé æ Partie
v ã Méthodes d 5essai des propriétés physiques des composants et inserts
Glas im Bauwesen æ MehrscheibenæIsolierglas æ Teil
vã Verfahren zur Prüfung der physikalischen Eigenschaften der Komponenten des Randverbundes und der Einbauten This European Standard was approved by CEN on
{ March
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t y {æ vã t r s z ESIST EN 1279-4:2018
EN 1279-4:2018 (E) 2 Contents Page European foreword . 5 1 Scope . 7 2 Normative references . 7 3 Terms and definitions . 7 4 Symbols and abbreviations . 8 4.1 Symbols and units . 8 4.2 Abbreviated terms . 9 4.3 Indexes . 9 5 Requirements for sealants . 9 5.1 General . 9 5.2 Physicochemical characterization . 10 5.3 Outer sealant strength. 11 5.4 Additional requirements . 12 5.5 Characteristics for the substitution of sealants .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.