iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12163:1998

(Main)

Copper and copper alloys - Rod for general purposes

Copper and copper alloys - Rod for general purposes

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy rod supplied in straight lengths, intended for general purposes. The sampling procedures and the methods of test for verification of conformity to the requirements of this standard are also specified.

Kupfer und Kupferlegierungen - Stangen zur allgemeinen Verwendung

Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und Grenzabmaße für in geraden Längen gelieferte Stangen aus Kupfer und Kupferlegierungen zur allgemeinen Verwendung fest. Der Ablauf der Probenentnahme, die Prüfverfahren zur feststellung der Übereinstimmung mit den Anforderungen der Norm und die Lieferbedingungen sind ebenfalls festgelegt.

Cuivre et alliages de cuivre - Barres pour usages généraux

La présente norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des barres en cuivre et alliages de cuivre livrées en longueurs droites, destinés à des usages généraux. Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente norme sont également spécifiées.

Baker in bakrove zlitine - Palice za splošno uporabo

General Information

Status
Withdrawn
Publication Date
20-Jan-1998
Withdrawal Date
31-May-2011
ICS
77.150.30 - Copper products
Technical Committee
CEN/TC 133 - Copper and copper alloys
Drafting Committee
CEN/TC 133/WG 4 - Extruded and drawn products, forgings and scrap
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Jun-2011
Completion Date
01-Jun-2011
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
Ref Project
SIST EN 12163:1998 - Copper and copper alloys - Rod for general purposes

Relations

Replaced By
EN 12163:2011 - Copper and copper alloys - Rod for general purposes
Effective Date
28-May-2011

Buy Standard

EN 12163:1998EN 12163:1998
PreviousNext
Standard
EN 12163:1998
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Palice za splošno uporaboKupfer und Kupferlegierungen - Stangen zur allgemeinen VerwendungCuivre et alliages de cuivre - Barres pour usages générauxCopper and copper alloys - Rod for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12163:1998SIST EN 12163:1998en01-november-1998SIST EN 12163:1998SLOVENSKI
STANDARD



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12163:1998



SIST EN 12
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1978:2022(Main)
Copper and copper alloys - Copper cathodes
SIST EN 1978:2022

This document specifies the composition and property requirements for cathodes of two copper grades, designated Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A).
Annex A (normative) describes methods for sampling cathodes for use in cases of dispute between the purchaser and the supplier. Annex B (informative) gives information on the relationships between electrical resistivity and conductivity of copper.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13601:2021(Main)
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
SIST EN 13601:2021

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross-sections and size ranges are:
— round, square and hexagonal rod with diameters or widths across-flats from 2 mm up to and including 160 mm;
— bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 250 mm;
— round, square, hexagonal and rectangular wire with diameters or widths across-flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this document are also specified.
NOTE Drawn, round copper wire, plain or tinned, single or multiline, for the manufacture of electrical conductors is specified in EN 13602.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13603:2021(Main)
Copper and copper alloys - Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes
SIST EN 13603:2021

This document specifies methods for assessing the tin coating on drawn round copper wire for the manufacture of electrical conductors, e.g. according to EN 13602.
This document includes test methods for the determination of the following characteristics:
a) thickness of the unalloyed tin coating;
b) continuity of the tin coating;
c) adherence of the tin coating.
WARNING — This document can involve the use of hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with their use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Moreover this document does not cover the aspects related to the people protection against the X-ray. To obtain information applicable to this aspect, it is convenient to refer to national and international standards, and also to the local regulations if they exist.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13605:2021(Main)
Copper and copper alloys - Copper profiles and profiled wire for electrical purposes
SIST EN 13605:2021

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes, which would fit within a circumscribing circle of maximum 180 mm diameter.
The sampling procedures, the test methods for verification of conformity to the requirements of this document, and the delivery conditions are also specified.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13600:2021(Main)
Copper and copper alloys - Seamless copper tubes for electrical purposes
SIST EN 13600:2021

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes, delivered in straight lengths or alternatively in level wound coils with the cross-sections and size ranges below:
- for round tubes in straight lengths with outside diameters from 3 mm up to and including 450 mm and wall thicknesses from 0,3 mm up to and including 10 mm;
- for round tubes in level wound coils with outside diameters from 3 mm up to and including 30 mm and wall thicknesses from 0,3 mm up to and including 10 mm;
- for square and rectangular tubes with major outside dimension from 5 mm up to and including 150 mm and wall thicknesses from 0,5 mm up to and including 10 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this document are also specified.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 13388:2020/AC:2020(Corrigendum)
Copper and copper alloys - Compendium of compositions and products
SIST-TS CEN/TS 13388:2020/AC:2020

TC origin - editorial modifications to Table 8

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 13388:2020(Main)
Copper and copper alloys - Compendium of compositions and products
SIST-TS CEN/TS 13388:2020

This document provides a summary of material designations, compositions and the product forms in which they are available, for coppers and copper alloys standardized in European Standards by CEN/TC 133 "Copper and copper alloys".

  • Technical specification
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1971-2:2019(Main)
Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface
SIST EN 1971-2:2020

This document specifies a procedure for the eddy current test with an internal probe for measuring defects on the inner surface of seamless round copper and copper alloy tubes.
This document applies particularly for finned tubes with high fins according to EN 12452.
NOTE   The eddy current test method(s) required, together with the size range and acceptance level, are defined in the relevant product standard.
The choice of the method for eddy current test:
-   with an encircling test coil on the outer surface according to prEN 1971-1
or
-   with an internal probe on the inner surface according to prEN 1971-2
is at the discretion of the manufacturer if there are no other agreements between the purchaser and the supplier.
Especially for finned tubes according to EN 12452 with high fins, it is suggested to use eddy current test with internal probe as described in this document.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1971-1:2019(Main)
Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 1: Test with an encircling test coil on the outer surface
SIST EN 1971-1:2020

This document specifies a procedure for the eddy current test with an encircling test coil for measuring defects on the outer surface of seamless round copper and copper alloy tubes.
NOTE   The eddy current test method(s) required, together with the size range and acceptance level, are defined in the relevant product standard.
The choice of the method for eddy current test:
-   with an encircling test coil on the outer surface according to prEN 1971-1;
or
-   with an internal probe on the inner surface according to prEN 1971-2;
is at the discretion of the manufacturer if there are no other agreements between the purchaser and the supplier.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17263:2019(Main)
Copper and copper alloys - Eddy current testing on the outer surface of rods, bars, hollow rods and wires for the detection of defects by encircling test coil
SIST EN 17263:2019

This document specifies a procedure for fully automatic eddy current testing with no operator involvement with an encircling test coil for detecting defects on the surface of copper and copper alloy rods, bars, hollow rods and wires with a minimum diameter or width across flats defined in the relevant product standards.
This test method can be continuous or discontinuous depending on the product.
The product size range and test acceptance level are defined in the relevant product standards.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day