HD 123.2 S1:1977
(Main)Hollow metallic waveguides - Part 2: Relevant specifications for ordinary rectangular waveguides
Hollow metallic waveguides - Part 2: Relevant specifications for ordinary rectangular waveguides
Contains a detailed description of ordinary rectangular waveguides - Type R, including mechanical requirements, electrical and gas tightness tests, and a table drawn up in inches and millimetres.
Metallische Hohlleiter - Teil 2: Allgemeine Empfehlungen für Rechteck-Hohlleite
Guides d'ondes métalliques creux - Partie 2: Spécifications particulières pour les guides d'ondes rectangulaires normaux
Contient une description détaillée des guides d'ondes rectangulaires normaux - type R, comprenant les prescriptions mécaniques, les essais électriques ainsi que les essais d'étanchéité au gaz, avec, en appui, un tableau de dimensions rédigé en inches et en millimètres.
Hollow metallic waveguides - Part 2: Relevant specifications for ordinary rectangular waveguides
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST HD 123.2 S1:2002
prva izdaja
STANDARD
september 2002
Hollow metallic waveguides - Part 2: Relevant specifications for ordinary rectangular
waveguides
ICS 33.120.10 Referenčna številka
SIST HD 123.2 S1:2002(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
NORME CEI
INTERNATIONALE IEC
60153-2
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
1974-01
Guides d'ondes métalliques creux
Deuxième partie:
Spécifications particulières pour les guides
d'ondes rectangulaires normaux
Hollow metallic waveguides
Part 2:
Relevant specifications for ordinary rectangular
waveguides
© IEC 1974 Droits de reproduction réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
L
PRICE CODE
International Electrotechnical Commission
IEC
MemuyHaponHas+ 3neMTpoTexHH4ecnaa HoMHCCHa
Pour prix, voir catalogue en vigueur
• • For price, see current catalogue
---------------------- Page: 2 ----------------------
— 3 —
CONTENTS
Page
FOREWORD 5
PREFACE 5
Clause
General 9
1.
1.1 Standardized types 9
9
1.2 Type designation
9
1.3 Frequency range
Mechanical requirements 9
2.
2.1 Dimensions 11
17
2.2 Other mechanical requirements
Electrical tests 19
3.
19
3.1 Attenuation
19
4. Additional tests
19
4.1 Gas tightness
21
TABLE I (in mm)
(in inches) 22
TABLE I
---------------------- Page: 3 ----------------------
— 5 —
INTERNATIONAL ELECTROTECHNICAL COMMISSION
HOLLOW METALLIC WAVEGUIDES
Relevant specifications for ordinary rectangular waveguides
Part 2 :
FOREWORD
1) The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the
an international con-
National Committees having a special interest therein are represented, express, as nearly as possible,
sensus of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in that
sense.
3) In order to promote international unification, the IEC expresses the wish that all National Committees should adopt the
text of the I EC recommendation for their national rules in so far as national conditions will permit. Any divergence
between the I EC recommendations and the corresponding national rules should, as far as possible, be clearly indicated
in the latter.
an indication of approval and has no responsibility when
4) The IEC has not laid down any procedure concerning marking as
an item of equipment is declared to comply with one of its recommendations.
PREFACE
This publication was prepared by Sub-Committee 46B, Waveguides and their Accessories, of Technical
Committee No. 46, Cables, Wires and Waveguides for Telecommunication Equipment.
It contains Part 2: Relevant Specifications for Ordinary Rectangular Waveguides, of the complete IEC
an d
recommendation for hollow metallic waveguides, it is intended to be used in conjunction with Part 1 :
General Requirements and Measuring Methods, which is issued as I EC Publication 153-1.
Detail specifications for other types of waveguides are issued in companion publications.
The amendments and supplements contained in this second edition of Publication 153-2 have been approved
in several Six Months' Rule documents.
The amendments to Table I were discussed at meetings held in Baden-Baden in June 1965 and in The Hague
in November 1970. The resulting drafts were submitted to the National Committees for approval under the
Six Months' Rule as follows :
document 46B(Central Office)26, circulated in February 1966
document 46B(Central Office)50, circulated in May 1971.
---------------------- Page: 4 ----------------------
The following countries voted explicitly in favour of publication :
Document Document
46B(Central Office)50
46B(Central Office)26
Belgium
Australia
Czechoslovakia
Belgium
Denmark
Czechoslovakia
France
Denmark
Germany
Finland
Iran
France
Israel
Germany
Italy
Israel
Japan
Italy
Netherlands
Japan
Poland
Netherlands
Portugal
Norway
Sweden
Poland
Switzerland Spain
Turkey
Sweden
United Kingdom
Switzerland
United States of America
Turkey
United States of America
The United Kingdom cast a negative vote on document 46B(Central Office)26.
and were deemed necessary
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.