EN 60286-3:2013
(Main)Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
IEC 60286-3:2013 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This standard also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips). This fifth edition cancels and replaces the fourth edition, published in 2007, as well as IEC 60286-3-1, published in 2009 and IEC 60286-3-2, published in 2009. It constitutes a full layout revision. In addition, this edition includes the following significant technical changes with respect to the previous edition: a) integration of IEC 60286-3-1:2009 as type 1b (Packaging of surface mount components on continuous pressed carrier tapes); b) integration of IEC 60286-3-2:2009 as type 2b (Packaging of surface mount components on blister carrier tapes 4 mm in width).
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung - Teil 3: Gurtung von oberflächenmontierbaren Bauelementen auf Endlosgurten
Emballage de composants pour opérations automatisées - Partie 3: Emballage des composants pour montage en surface en bandes continues
La CEI 60286-3:2013 est applicable à la mise en bande des composants électroniques sans fils de sortie ou avec tronçons de sortie destinés à être connectés à des circuits électroniques. Elle fournit uniquement les dimensions essentielles pour la mise sur bande de composants destinés aux opérations mentionnées ci-dessus. La présente norme inclut également des exigences relatives à l'emballage de produits à puce isolée incluant puces nues et puces à contact (puces retournées). Cette cinquième édition annule et remplace la quatrième édition parue en 2007, la CEI 60286 3-1, parue en 2009 et la CEI 60286 3-2, parue en 2009. Elle constitue une révision complète de la topologie. En outre, cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) intégration de la CEI 60286-3-1:2009 comme type 1b (Emballage de composants pour montage en surface sur des bandes d'entraînement continues formées à la presse; b) intégration de la CEI 60286-3-2:2009 comme type 2b (Emballage de composants pour montage en surface sur des bandes d'entraînement gaufrées de 4 mm de large).
Pakiranje komponent za avtomatsko ravnanje - 3. del: Pakiranje komponent za površinsko montažo na neprekinjenih trakovih
Ta del standarda IEC 60286 se uporablja za tračno pakiranje elektronskih komponent brez vodov ali ostankov vodov, namenjenih za povezavo z elektronskimi vezji. Vključuje samo dimenzije, bistvene za tračno pakiranje komponent, ki so namenjene za zgoraj navedene namene. Ta standard vključuje tudi zahteve glede pakiranja proizvodov s singularnimi polprevodniškimi integriranimi vezji, vključno s tistimi brez ohišja in tistimi z izboklinami (»flip chip«).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60286-3:2013
01-oktober-2013
Pakiranje komponent za avtomatsko ravnanje - 3. del: Pakiranje komponent za
površinsko montažo na neprekinjenih trakovih
Packaging of components for automatic handling - Part 3: Packaging of surface mount
components on continuous tapes
Gurtung und Magazinierung von Bauelementen für die automatische Verarbeitung - Teil
3: Gurtung von oberflächenmontierbaren Bauelementen auf Endlosgurten
Emballage de composants pour opérations automatisées - Partie 3: Emballage des
composants pour montage en surface en bandes continues
Ta slovenski standard je istoveten z: EN 60286-3:2013
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.060 Tulci. Vretena Spools. Bobbins
SIST EN 60286-3:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60286-3:2013
---------------------- Page: 2 ----------------------
SIST EN 60286-3:2013
EUROPEAN STANDARD
EN 60286-3
NORME EUROPÉENNE
August 2013
EUROPÄISCHE NORM
ICS 31.020; 31.240 Supersedes EN 60286-3:2007
English version
Packaging of components for automatic handling -
Part 3: Packaging of surface mount components on continuous tapes
(IEC 60286-3:2013)
Emballage de composants pour Gurtung und Magazinierung von
opérations automatisées - Bauelementen für die automatische
Partie 3: Emballage des composants pour Verarbeitung -
montage en surface en bandes continues Teil 3: Gurtung von
(CEI 60286-3:2013) oberflächenmontierbaren Bauelementen
auf Endlosgurten
(IEC 60286-3:2013)
This European Standard was approved by CENELEC on 2013-06-21. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60286-3:2013 E
---------------------- Page: 3 ----------------------
SIST EN 60286-3:2013
EN 60286-3:2013 - 2 -
Foreword
The text of document 40/2200/FDIS, future edition 5 of IEC 60286-3, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60286-3:2013.
The following dates are fixed:
(dop) 2014-03-21
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2016-06-21
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60286-3:2007.
EN 60286-3:2013 includes the following significant technical changes with respect to
EN 60286-3:2007:
a) integration of EN 60286-3-1:2009 as type 1b (Packaging of surface mount components on
continuous pressed carrier tapes);
b) integration of EN 60286-3-2:2009 as type 2b (Packaging of surface mount components on blister
carrier tapes 4 mm in width).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60286-3:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60286-3-1:2009 NOTE Harmonised as EN 60286-3-1:2009 (not modified).
IEC 60286-3-2:2009 NOTE Harmonised as EN 60286-3-2:2009 (not modified).
IEC/TR 62258-3 NOTE Harmonised as CLC/TR 6
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.