iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 62321-4:2014/A1:2017

(Amendment)

Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS

Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS

Verfahren zur Bestimmung von bestimmten Substanzen in Produkten der Elektrotechnik - Teil 4: Quecksilber in Polymeren, Metallen und Elektronik mit CV-AAS, CV-AFS, ICP-OES und ICP-MS

Détermination de certaines substances dans les produits électrotechniques - Partie 4: Mercure dans les polymères, métaux et produits électroniques par CV-AAS, CV-AFS, ICP-OES et ICP-MS

Določevanje posameznih snovi v elektrotehničnih izdelkih - 4. del: Določevanje živega srebra v polimerih, kovinah in elektroniki s CV-AAS, CV-AFS, ICP-OES in ICP-MS - Dopolnilo A1

General Information

Status
Published
Publication Date
16-Nov-2017
Withdrawal Date
16-Aug-2020
ICS
13.020 - Environmental protection
43.040.10 - Electrical and electronic equipment
Technical Committee
CLC/TC 111X - Environment
Drafting Committee
IEC/TC 111 - Environmental standardization for electrical and electronic products and systems
Current Stage
6060 - Document made available - Publishing
Start Date
17-Nov-2017
Completion Date
17-Nov-2017
Directive
2011/65/EU - DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
Ref Project
SIST EN 62321-4:2014/A1:2018 - Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS

Relations

Amends
EN 62321-4:2014 - Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS
Effective Date
08-Mar-2016

Buy Standard

EN 62321-4:2014/A1:2018EN 62321-4:2014/A1:2018
PreviousNext
Amendment
EN 62321-4:2014/A1:2018
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62321-4:2014/A1:2018
01-januar-2018
'RORþHYDQMHSRVDPH]QLKVQRYLYHOHNWURWHKQLþQLKL]GHONLKGHO'RORþHYDQMH
åLYHJDVUHEUDYSROLPHULKNRYLQDKLQHOHNWURQLNLV&9$$6&9$)6,&32(6LQ
,&306'RSROQLOR$
Determination of certain substances in electrotechnical products - Part 4: Mercury in
polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS
Verfahren zur Bestimmung von bestimmten Substanzen in Produkten der Elektrotechnik
- Teil 4: Quecksilber in Polymeren, Metallen und Elektronik mit CV-AAS, CV-AFS, ICP-
OES und ICP-MS
Détermination de certaines substances dans les produits électrotechniques - Partie 4:
Mercure dans les polymères, métaux et produits électroniques par CV-AAS, CV-AFS,
ICP-OES et ICP-MS
Ta slovenski standard je istoveten z: EN 62321-4:2014/A1:2017
ICS:
29.020 Elektrotehnika na splošno Electrical engineering in
general
31.020 Elektronske komponente na Electronic components in
splošno general
SIST EN 62321-4:2014/A1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62321-4:2014/A1:2018

---------------------- Page: 2 ----------------------

SIST EN 62321-4:2014/A1:2018


EUROPEAN STANDARD EN 62321-4:2014/A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2017
ICS 13.020; 43.040.10

English Version
Determination of certain substances in electrotechnical products
- Part 4: Mercury in polymers, metals and electronics
by CV-AAS, CV-AFS, ICP-OES and ICP-MS
(IEC 62321-4:2013/A1:2017)
Détermination de certaines substances dans les produits Verfahren zur Bestimmung von bestimmten Substanzen in
électrotechniques - Partie 4: Mercure dans les polymères, Produkten der Elektrotechnik - Teil 4: Quecksilber in
métaux et produits électroniques par CV-AAS, CV-AFS, Polymeren, Metallen und Elektronik mit CV-AAS, CV-AFS,
ICP-OES et ICP-MS ICP-OES und ICP-MS
(IEC 62321-4:2013/A1:2017) (IEC 62321-4:2013/A1:2017)
This amendment A1 modifies the European Standard EN 62321-4:2014; it was approved by CENELEC on 2017-08-17. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62321-4:2014/A1:2017 E

---------------------- Page: 3 ----------------------

SIST EN 62321-4:2014/A1:2018
EN 62321-4:2014/A1:2017
European foreword
The text of document 111/414/CDV, future IEC 62321-4:2013/A1, prepared by IEC/TC 111
"Environmental standardization for electrical and electronic products and systems" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 62321-4:2014/A1:2017.

The following dates are fixed:
(dop) 2018-05-17
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-08-17
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62321-4:2013/A1:2017 was approved by CENELEC as a
European Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 62321-4:2014/A1:2018



IEC 62321-4

®


Edition 1.0 2017-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




A MENDMENT 1

AM ENDEMEN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62321-2:2021(Main)
Determination of certain substances in electrotechnical products - Part 2: Disassembly, disjointment and mechanical sample preparation
SIST EN IEC 62321-2:2022

This part of IEC 62321 provides strategies of sampling along with the mechanical preparation of samples from electrotechnical products. These samples can be used for analytical testing to determine the levels of certain substances as described in the test methods in other parts of the IEC 62321 series. Restrictions for substances will vary between geographic regions and can be updated on a regular basis. This document describes a generic process for obtaining and preparing samples prior to the determination of any substance of concern. This document does not provide: - full guidance on each and every product that could be classified as electrotechnical product. Since there is a huge variety of electrotechnical parts, with various structures and compositions, along with the continuous innovations in the industry, it is unrealistic to attempt to provide procedures for the disjointment of every type of part; - guidance regarding other routes to gather additional information on certain substances in a product, although the information collected has relevance to the sampling strategies in this document; - safe disassembly and mechanical disjointment instructions related to electrotechnical products (e.g. mercury-containing switches) and the recycling industry (e.g. how to handle CRTs or the safe removal of batteries). See IEC 62554 [1] 1 for the disjointment and mechanical sample preparation of mercury-containing fluorescent lamps; - sampling procedures for packaging and packaging materials; - analytical procedures to measure the levels of certain substances. This is covered by other standards (e.g. other parts of the IEC 62321 series), which are referred to as "test standards" in this document; - guidelines for assessment of compliance. This document has the status of a horizontal standard in accordance with IEC Guide 108 [2].

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-7-1:2015(Main)
Determination of certain substances in electrotechnical products - Part 7-1: Hexavalent chromium - Presence of hexavalent chromium (Cr(VI)) in colorless and colored corrosion-protected coatings on metals by the colorimetric method
SIST EN 62321-7-1:2016

IEC 62321-7-1:2015 describes a boiling water extraction procedure intended to provide a qualitative determination of the presence of hexavalent chromium (Cr(VI)) in colourless and coloured corrosion-protection coatings on metallic samples. In this procedure, when Cr(VI) in a sample is detected below the 0,10 g/cm2 LOQ (limit of quantification), the sample is considered to be negative for Cr(VI). Since Cr(VI) may not be uniformly distributed in the coating even within the same sample batch, a "grey zone" between 0,10 g/cm2 and 0,13 g/cm2 has been established as "inconclusive" to reduce inconsistent results due to unavoidable coating variations. In this case, additional testing may be necessary to confirm the presence of Cr(VI). When Cr(VI) is detected above 0,13 g/cm2, the sample is considered to be positive for the presence of Cr(VI) in the coating layer.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-6:2015(Main)
Determination of certain substances in electrotechnical products - Part 6: Polybrominated biphenyls and polybrominated diphenyl ethers in polymers by gas chromatography-mass spectrometry (GC-MS)
SIST EN 62321-6:2015

IEC 62321-6:2015 specifies one normative and two informative techniques for the determination of polybrominated biphenyls (PBB) and diphenyl ethers (PBDE) in polymers of electrotechnical products. The test methods are: - The gas chromatography-mass spectrometry (GC-MS); - The ion attachment mass spectrometry (IAMS) technique and - The high-pressure liquid chromatography technique. This first edition of IEC 62321-6 is a partial replacement of IEC 62321:2008, forming a structural revision and generally replacing Annex A.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-4:2014(Main)
Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS
SIST EN 62321-4:2014

IEC 62321-4:2013 describes the use of four test methods for mercury in polymers, metals and electronics, namely CV-AAS (cold vapour atomic absorption spectrometry), CV-AFS (cold vapour atomic fluorescence spectrometry) ICP-OES (inductively coupled plasma optical emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry) as well as several procedures for preparing the sample solution from which the most appropriate method of analysis can be selected by experts.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-2:2014(Main)
Determination of certain substances in electrotechnical products - Part 2: Disassembly, disjointment and mechanical sample preparation
SIST EN 62321-2:2014

IEC 62321-2:2013 provides strategies of sampling along with the mechanical preparation of samples from electrotechnical products, electronic assemblies and electronic components. These samples can be used for analytical testing to determine the levels of certain substances as described in the test methods in other parts of IEC 62321. Restrictions for substances will vary between geographic regions and from time to time. This Standard describes a generic process for obtaining and preparing samples prior to the determination of any substance which are under concern.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-5:2014(Main)
Determination of certain substances in electrotechnical products - Part 5: Cadmium, lead and chromium in polymers and electronics and cadmium and lead in metals by AAS, AFS, ICP-OES and ICP-MS
SIST EN 62321-5:2014

IEC 62321-5:2013 describes the four test methods for lead, cadmium and chromium in polymers, metals and electronics, namely AAS (atomic absorption spectrometry), AFS (atomic fluorescence spectrometry), ICP-OES (inductively coupled plasma optical emission spectrometry), and ICP-MS (inductively coupled plasma mass spectrometry) as well as several procedures for preparing the sample solution from which the most appropriate method of analysis can be selected by experts.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-3-1:2014(Main)
Determination of certain substances in electrotechnical products - Part 3-1: Screening - Lead, mercury, cadmium, total chromium and total bromine by X-ray fluorescence spectrometry
SIST EN 62321-3-1:2014

IEC 62321-3-1:2013 describes the screening analysis of five substances, specifically lead (Pb), mercury (Hg), cadmium (Cd), total chromium (Cr) and total bromine (Br) in uniform materials found in electrotechnical products, using the analytical technique of X-ray fluorescence (XRF) spectrometry.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-3-2:2014(Main)
Determination of certain substances in electrotechnical products - Part 3-2: Screening - Total bromine in polymers and electronics by Combustion - Ion Chromatography
SIST EN 62321-3-2:2014

IEC 62321-3-2:2013 specifies the screening analysis of the total bromine (Br) in homogeneous materials found in polymers and electronics by using the analytical technique of combustion ion chromatography (C-IC).

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62321-1:2013(Main)
Determination of certain substances in electrotechnical products - Part 1: Introduction and overview
SIST EN 62321-1:2014

IEC 62321-1:2013 refers to the sample as the object to be processed and measured. The nature of the sample and the manner in which it is acquired is defined by the entity carrying out the tests and not by this standard. It provides guidance on the disassembly procedure employed for obtaining a sample. This first edition of IEC 62321-1 is a partial replacement of IEC 62321, forming a structural revision and replacing Clauses 1 to 4.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62321-2:2021(Main)
Determination of certain substances in electrotechnical products - Part 2: Disassembly, disjointment and mechanical sample preparation
SIST EN IEC 62321-2:2022

This part of IEC 62321 provides strategies of sampling along with the mechanical preparation of samples from electrotechnical products. These samples can be used for analytical testing to determine the levels of certain substances as described in the test methods in other parts of the IEC 62321 series. Restrictions for substances will vary between geographic regions and can be updated on a regular basis. This document describes a generic process for obtaining and preparing samples prior to the determination of any substance of concern. This document does not provide: - full guidance on each and every product that could be classified as electrotechnical product. Since there is a huge variety of electrotechnical parts, with various structures and compositions, along with the continuous innovations in the industry, it is unrealistic to attempt to provide procedures for the disjointment of every type of part; - guidance regarding other routes to gather additional information on certain substances in a product, although the information collected has relevance to the sampling strategies in this document; - safe disassembly and mechanical disjointment instructions related to electrotechnical products (e.g. mercury-containing switches) and the recycling industry (e.g. how to handle CRTs or the safe removal of batteries). See IEC 62554 [1] 1 for the disjointment and mechanical sample preparation of mercury-containing fluorescent lamps; - sampling procedures for packaging and packaging materials; - analytical procedures to measure the levels of certain substances. This is covered by other standards (e.g. other parts of the IEC 62321 series), which are referred to as "test standards" in this document; - guidelines for assessment of compliance. This document has the status of a horizontal standard in accordance with IEC Guide 108 [2].

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day