EN IEC 61188-6-4:2019

Printed boards and printed board assemblies - Design and use - Part 6-4: Land pattern design - Generic requirements for dimensional drawings of surface mounted components (SMD) from the viewpoint of land pattern design

IEC 61188-6-4:2019 specifies generic requirements for dimensional drawings of SMD from the viewpoint of land pattern design. The purpose of this document is to prevent land pattern design issues caused by lack of information and/or misuse of the information from SMD outline drawing as well as to improve the utilization of IEC 61188 series. This document is applicable to the SMD of semiconductor devices and electrical components.

Leiterplatten und Flachbaugruppen - Konstruktion und Anwendung - Teil 6-4: Konstruktion des Anschlussflächenbilds - Allgemeine Anforderungen an SMD-Maßzeichnungen hinsichtlich der Konstruktion des Anschlussflächenbilds

Cartes imprimées et cartes imprimées équipées - Conception et utilisation - Partie 6-4: Conception de la zone de report - Exigences génériques pour les dessins dimensionnels de composants montés en surface (CMS) du point de vue de la conception de la zone de report

L'IEC 61188-6-4:2019 spécifie les exigences génériques pour les dessins dimensionnels de CMS du point de vue de la conception de la zone de report. Le présent document a pour objet d'éviter les problèmes de conception de la zone de report causés par un manque d'informations et/ou une mauvaise utilisation des informations provenant des dessins d'encombrement de CMS, ainsi que d'améliorer l'utilisation de la série IEC 61188. Le présent document est applicable au CMS de dispositifs à semiconducteurs et de composants électriques.

Plošče tiskanih vezij in sestavi plošč tiskanih vezij - Zasnova in uporaba - 6-4. del: Razmestitev priključkov - Splošne zahteve za merske risbe elementov za površinsko montažo (SMD) glede na razmestitev njihovih priključkov

Ta standard določa splošne zahteve za merske risbe elementov za površinsko montažo (SMD) glede na razmestitev njihovih priključkov. Namen tega dokumenta je preprečevanje težav pri razmestitvi priključkov zaradi pomanjkanja informacij in/ali zlorabe informacij iz opisa risbe elementov za površinsko montažo ter izboljšana uporaba skupine standardov IEC 61188. Ta dokument se uporablja za elemente za površinsko montažo polprevodniških elementov in električnih komponent.

General Information

• Status: Published
• Publication Date: 04-Jul-2019
• Withdrawal Date: 05-Jun-2022
• ICS: 31.180 - Printed circuits and boards
• Technical Committee: CLC/SR 91 - Electronics assembly technology
• Drafting Committee: IEC/TC 91 - IEC_TC_91
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 05-Jul-2019
• Completion Date: 05-Jul-2019
• Ref Project: SIST EN IEC 61188-6-4:2019 - Printed boards and printed board assemblies - Design and use - Part 6-4: Land pattern design - Generic requirements for dimensional drawings of surface mounted components (SMD) from the viewpoint of land pattern design

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61188-6-4:2019
01-november-2019
Plošče tiskanih vezij in sestavi plošč tiskanih vezij - Zasnova in uporaba - 6-4. del:
Razmestitev priključkov - Splošne zahteve za merske risbe elementov za
površinsko montažo (SMD) glede na razmestitev njihovih priključkov
Printed boards and printed board assemblies - Design and use - Part 6-4: Land pattern
design - Generic requirements for dimensional drawings of surface mounted components
(SMD) from the viewpoint of land pattern design
Ta slovenski standard je istoveten z: EN IEC 61188-6-4:2019
ICS:
01.100.25 Risbe s področja Electrical and electronics
elektrotehnike in elektronike engineering drawings
31.180 Tiskana vezja (TIV) in tiskane Printed circuits and boards
plošče
SIST EN IEC 61188-6-4:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61188-6-4:2019

---------------------- Page: 2 ----------------------
SIST EN IEC 61188-6-4:2019


EUROPEAN STANDARD EN 61188-6-4

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2019
ICS 31.180

English Version
Printed boards and printed board assemblies - Design and use -
Part 6-4: Land pattern design - Generic requirements for
dimensional drawings of surface mounted components (SMD)
from the viewpoint of land pattern design
(IEC 61188-6-4:2019)
Cartes imprimées et cartes imprimées équipées - Leiterplatten und Flachbaugruppen - Konstruktion und
Conception et utilisation - Partie 6-4: Conception de la zone Anwendung - Teil 6-4: Allgemeine Anforderungen an SMD-
de report - Exigences génériques pour les dessins Maßzeichnungen hinsichtlich der Konstruktion des
dimensionnels de composants montés en surface (CMS) du Anschlussflächenbilds
point de vue de la conception de la zone de report (IEC 61188-6-4:2019)
(IEC 61188-6-4:2019)
This European Standard was approved by CENELEC on 2019-06-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of Nort Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61188-6-4:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61188-6-4:2019


EN 61188-6-4:2019 (E)

European foreword
The text of document 91/1561/FDIS, future edition 1 of IEC 61188-6-4, prepared by IEC/TC 91 "Electronics
assembly technology" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 61188-6-4:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national level by (dop) 2020-03-06
publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-06-06
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61188-6-4:2019 was approved by CENELEC as a European
Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60191-1 NOTE Harmonized as EN IEC 60191-1
IEC 60191-6 NOTE Harmonized as EN 60191-6
IEC 60191-6-1 NOTE Harmonized as EN 60191-6-1
IEC 61188-5-1 NOTE Harmonized as EN 61188-5-1
IEC 61188-5-2 NOTE Harmonized as EN 61188-5-2
IEC 61188-5-3 NOTE Harmonized as EN 61188-5-3
IEC 61188-5-4 NOTE Harmonized as EN 61188-5-4
IEC 61188-5-5 NOTE Harmonized as EN 61188-5-5
IEC 6118
...