Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 4-1: Particular requirements for chain saws

IEC 62841-4-1:2017 applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. This standard does not apply to chain saws for tree service as defined in ISO 11681-2; or pole-mounted pruners. Pole-mounted pruners will be covered by a future part of IEC 62841. The chain saws covered by this standard are designed only to be operated with the right hand on the rear handle and the left hand on the front handle. This Part 4-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen – Sicherheit - Teil 4-1: Besondere Anforderungen für Kettensägen

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 4-1: Exigences particulières pour les scies à chaîne

IEC 62841-4-1:2017 s'applique aux scies à chaîne pour la découpe du bois et conçues pour être utilisées par une personne. La présente Norme ne couvre pas les scies à chaîne conçues pour être utilisées conjointement avec un guide-chaîne et une fendeuse, ni de toute autre manière (avec un support ou en tant que machine fixe ou portable, par exemple). La présente Norme ne s'applique pas aux scies à chaîne pour l'élagage telles que définies dans l'ISO 11681-2; ou aux élagueurs sur perche. Les élagueurs sur perche sont couverts par une partie ultérieure de l'IEC 62841. Les scies à chaîne couvertes par la présente Norme sont conçues uniquement pour être utilisées main droite sur la poignée arrière et main gauche sur la poignée avant. La présente Partie 4-1 doit être utilisée conjointement avec la première édition de l'IEC 62841-1 (2014). L’attention des Comités Nationaux est attirée sur le fait que les fabricants d’appareils et les organismes d’essai peuvent avoir besoin d’une période transitoire après la publication d’une nouvelle publication IEC, ou d’une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication. Mots clés: scies à chaîne, Outils électroportatifs, Sécurité

Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-1. del: Posebne zahteve za verižne žage (IEC 62841-4-1:2017)

General Information

Status
Published
Publication Date
12-Mar-2020
Current Stage
6060 - Document made available - Publishing
Start Date
13-Mar-2020
Completion Date
13-Mar-2020

Relations

Buy Standard

Standard
EN 62841-4-1:2020 - BARVE
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62841-4-1:2020
01-junij-2020
Nadomešča:
SIST EN 60745-2-13:2009
SIST EN 60745-2-13:2009/A1:2011
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-
1. del: Posebne zahteve za verižne žage (IEC 62841-4-1:2017)
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 4-1: Particular requirements for chain saws (IEC 62841-4-
1:2017)
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit - Teil 4-1: Besondere Anforderungen für
Kettensägen (IEC 62841-4-1:2017)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 4-1: Exigences particulières pour les scies à chaîne (IEC 62841-4-
1:2017)
Ta slovenski standard je istoveten z: EN 62841-4-1:2020
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
65.060.80 Gozdarska oprema Forestry equipment
SIST EN 62841-4-1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 62841-4-1:2020

---------------------- Page: 2 ----------------------
SIST EN 62841-4-1:2020

EUROPEAN STANDARD EN 62841-4-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2020
ICS 25.140.20 Supersedes EN 60745-2-13:2009 and all of its
amendments and corrigenda (if any)
English Version
Electric Motor-Operated Hand-Held Tools, Transportable Tools
and Lawn and Garden Machinery - Safety - Part 4-1: Particular
requirements for chain saws
(IEC 62841-4-1:2017 , modified)
Outils électroportatifs à moteur, outils portables et machines
Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 4-1: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à chaîne Gartenmaschinen - Sicherheit - Teil 4-1: Besondere
(IEC 62841-4-1:2017 , modifiée) Anforderungen für Kettensägen
(IEC 62841-4-1:2017 , modifiziert)
This European Standard was approved by CENELEC on 2017-11-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62841-4-1:2020 E

---------------------- Page: 3 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

European foreword
The text of document 116/339/FDIS, future edition 1 of IEC 62841-4-1, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-4-1:2020.
A draft amendment, which covers common modifications to IEC 62841-4-1 (116/339/FDIS), was prepared
by CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
• latest date by which this document has (dop) 2020-09-13
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2024-03-13
standards conflicting with this document
have to be withdrawn
EN 62841-4-1:2020 supersedes EN 60745-2-13:2009 + A1:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.