iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60384-14:2013

(Main)

Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains

Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains

IEC 60384-14:2013 applies to capacitors and resistor-capacitor combinations which will be connected to an a.c. mains or other supply with nominal voltage not exceeding 1 000 V a.c. (r.m.s.) or 1 000 V d.c. and with a nominal frequency not exceeding 100 Hz. This fourth edition cancels and replaces the third edition published in 2005. It constitutes a technical revision. All changes that have been agreed upon can be categorized as minor revisions.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 14: Rahmenspezifikation - Festkondensatoren zur Unterdrückung elektromagnetischer Störungen, geeignet für Netzbetrieb

Condensateurs fixes utilisés dans les équipements électroniques - Partie 14: Spécification intermédiaire - Condensateurs fixes d'antiparasitage et raccordement à l'alimentation

La CEI 60384-14:2013 s'applique aux condensateurs et aux combinaisons condensateur/résistance qui sont connectés à un réseau d'alimentation en courant alternatif ou à une autre alimentation dont la tension nominale ne dépasse pas 1 000 V c.a. (efficace) ou 1 000 V c.c. et dont la fréquence nominale ne dépasse pas 100 Hz. Cette quatrième édition annule et remplace la troisième édition publiée en 2005 dont elle constitue une révision technique. Toutes les modifications acceptées peuvent être classées comme des révisions mineures.

Fiksni kondenzatorji za uporabo v elektronskih napravah - 14. del: Področna specifikacija - Fiksni kondenzatorji za dušenje elektromagnetnega motenja in za povezovanje z omrežnim napajanjem (IEC 60384-14:2013)

Ta del standarda IEC 60384 velja za kondenzatorje in kombinacije uporov/kondenzatorjev, ki se priključijo v izmenično napajalno omrežje ali drug vir napajanja z nazivno sistemsko napetostjo do 1000 V izmenične napetosti (efektivne izmenične napetosti) ali do 1000 V enosmerne napetosti in z nazivno frekvenco do 100 Hz.

General Information

Status
Published
Publication Date
29-Aug-2013
Withdrawal Date
09-Jul-2016
ICS
31.060.10 - Fixed capacitors
Technical Committee
CLC/TC 40XA - CLC/TC 40XA
Drafting Committee
IEC/TC 40 - IEC_TC_40
Current Stage
6060 - Document made available - Publishing
Start Date
30-Aug-2013
Completion Date
30-Aug-2013
Ref Project
SIST EN 60384-14:2014 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains

Relations

Replaces
EN 60384-14:2005 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
Effective Date
29-Jan-2023
Replaced By
EN IEC 60384-14:2023 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
Effective Date
26-Jan-2023
Amended By
EN 60384-14:2013/A1:2016 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
Effective Date
26-Jan-2023
Corrected By
EN 60384-14:2013/AC:2016-04 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
Effective Date
26-Jan-2023

Buy Standard

EN 60384-14:2014EN 60384-14:2014
PreviousNext
Standard
EN 60384-14:2014
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60384-14:2014
01-maj-2014
)LNVQLNRQGHQ]DWRUML]DXSRUDERYHOHNWURQVNLKQDSUDYDKGHO3RGURþQD
VSHFLILNDFLMD)LNVQLNRQGHQ]DWRUML]DGXãHQMHHOHNWURPDJQHWQHJDPRWHQMDLQ]D
SRYH]RYDQMH]RPUHåQLPQDSDMDQMHP ,(&
Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed
capacitors for electromagnetic interference suppression and connection to the supply
mains
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 14:
Rahmenspezifikation - Festkondensatoren zur Unterdrückung elektromagnetischer
Störungen, geeignet für Netzbetrieb
Condensateurs fixes utilisés dans les équipements électroniques - Partie 14:
Spécification intermédiaire - Condensateurs fixes d'antiparasitage et raccordement à
l'alimentation
Ta slovenski standard je istoveten z: EN 60384-14:2013
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN 60384-14:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60384-14:2014

---------------------- Page: 2 ----------------------

SIST EN 60384-14:2014

EUROPEAN STANDARD
EN 60384-14

NORME EUROPÉENNE
August 2013
EUROPÄISCHE NORM

ICS 31.060.10 Supersedes EN 60384-14:2005


English version


Fixed capacitors for use in electronic equipment -
Part 14: Sectional specification -
Fixed capacitors for electromagnetic interference suppression and
connection to the supply mains
(IEC 60384-14:2013)


Condensateurs fixes utilisés dans les Festkondensatoren zur Verwendung in
équipements électroniques - Geräten der Elektronik -
Partie 14: Spécification intermédiaire - Teil 14: Rahmenspezifikation -
Condensateurs fixes d'antiparasitage et Festkondensatoren zur Unterdrückung
raccordement à l'alimentation elektromagnetischer Störungen, geeignet
(CEI 60384-14:2013) für Netzbetrieb
(IEC 60384-14:2013)




This European Standard was approved by CENELEC on 2013-07-10. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-14:2013 E

---------------------- Page: 3 ----------------------

SIST EN 60384-14:2014
EN 60384-14:2013 - 2 -

Foreword
The text of document 40/2199/FDIS, future edition 4 of IEC 60384-14, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60384-14:2013.
The following dates are fixed:
(dop) 2014-04-10
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-07-10
• latest date by which the national

standards conflicting with the
document have to be withdrawn

This document supersedes EN 60384-14:2005.

EN 60384-14:2013 includes the following significant technical changes with respect to
EN 60384-14:2005:
All changes that have been agreed upon can be categorized as minor revisions.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 60384-14:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:

IEC 60335-1 NOTE Harmon
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60384-23:2023(Main)
Fixed capacitors for use in electronic equipment - Part 23: Sectional specification - Fixed metallized polyethylene naphthalate film dielectric surface mount DC capacitors
SIST EN IEC 60384-23:2023

IEC 60384-23:2023 is available as IEC 60384-23:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60384-23:2023 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyethylene naphthalate dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. This part of IEC 60384 specifies preferred ratings and characteristics, selects from IEC 60384‑1:2021 the appropriate quality assessment procedures, tests and measuring methods and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384‑14. This edition includes the following significant technical changes with respect to the previous edition: - this edition includes the following significant technical changes with respect to the previous edition: revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents; - the document structure has been organized to follow new sectional specification structure decided in TC 40; - revised tables and Clause 5 so as to prevent duplications and contradictions; - in Subclause 5.2 (Mounting), the Subclauses 5.2.1, 5.2.2 and 5.2.3 have been added; - in Subclause 5.5 (Shear test), the Subclauses 5.5.1 and 5.5.2 have been added; - in Subclause 5.14 (Component solvent resistance), the Subclauses 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 (Final inspections and requirements) in Group 1A and in Subgroup C1; - in Subclause 5.15 (Solvent resistance of marking), the Subclauses 5.15.1 and 5.15.2 have been added; - tangent of loss angle measurement has been added to the resistance to soldering heat test; - lot-by-lot and periodical inspection tables including requirements have been moved to Annex A; - revised Inspection Level (IL) of A1 subgroup.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-20:2023(Main)
Fixed capacitors for use in electronic equipment - Part 20: Sectional specification - Fixed metallized polyphenylene sulfide film dielectric surface mount DC capacitors
SIST EN IEC 60384-20:2023

IEC 60384-20:2023 is available as IEC 60384-20:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60384-20:2023 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyphenylene sulfide dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. This part of IEC 60384 specifies preferred ratings and characteristics and selects from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level; lower performance levels are not permitted. Capacitors for electromagnetic interference suppression are not included but are covered by IEC 60384‑14. This edition includes the following significant technical changes with respect to the previous edition: - revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents; - the document structure has been organized to follow new sectional specification structure decided in TC 40; - revised tables and Clause 5 so as to prevent duplications and contradictions; - in Clause 5.2 (Mounting), the Subclauses 5.2.1, 5.2.2 and 5.2.3 have been added; - in Subclause 5.5 (Shear test), the Subclauses 5.5.1 and 5.5.2 have been added; - in Subclause 5.14 (Component solvent resistance), the Subclauses 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 (Final inspections and requirements) in Group 1A and in Subgroup C1; - in Subclause 5.15 (Solvent resistance of marking), the Subclauses 5.15.1 and 5.15.2 have been added; - tangent of loss angle measurement has been added to resistance to soldering heat test; - lot-by-lot and periodical inspection tables, including requirements, have been moved to Annex A; - revised Inspection Level (IL) of A1 subgroup.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-14:2023(Main)
Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
SIST EN IEC 60384-14:2023

IEC 60384-14:2023 applies to capacitors and resistor-capacitor combinations intended to be connected to AC mains or other supply with a nominal voltage not exceeding 1 000 V AC (RMS), and with a nominal frequency not exceeding 100 Hz. This document includes also additional specific conditions and requirements for the connection to DC supplies with a rated voltage not exceeding 1 500 V DC. The principal object of this part of IEC 60384 is to prescribe preferred ratings and characteristics and to select, from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance level; lower performance levels are not permitted. This document also provides a schedule of safety tests to be used by national testing stations in countries where approval by such stations is required. The overvoltage categories in combination with the AC mains voltages for the capacitors classified in this document are to be taken from IEC 60664-1. This edition includes the following significant technical changes with respect to the previous edition:
in damp heat steady state test, all capacitor types are tested both with and without rated voltage; the number of test pieces has been increased;
tangent of loss angle is added In Group 0 tests, in safety tests only;
qualification approval based on safety and performance tests has been removed from the main text to a normative annex;
the range of rated voltages is given instead of exact rated voltage values;
normative annex for description of capacitor styles and of creepage/clearance distance measurement has been added;
the importance of mechanical failures (cracks) in component encapsulation as a safety feature is highlighted in handling instructions and requirements after all relevant tests.

  • Standard
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62391-1:2022(Main)
Fixed electric double-layer capacitors for use in electric and electronic equipment - Part 1: Generic specification
SIST EN IEC 62391-1:2023

IEC 62391-1:2022 applies to fixed electric double-layer capacitors (hereafter referred to as capacitors) mainly used in DC circuits of electric and electronic equipment. This part of IEC 62391 establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. This edition includes the following significant technical changes with respect to the previous edition:
The document has been completely restructured to comply with the ISO/IEC Directives, Part 2; a new technical categorization of test methods has been introduced and the test methods have been reorganized according to these new categories; tables, figures and references have been revised accordingly.
Calculation formula of charging/discharging efficiency in Annex D were divided into two cases: "Calculation assuming full charge and discharge" and "Calculation assuming incomplete charging and discharging due to internal resistance".

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-1-1:2022(Main)
Fixed capacitors for use in electronic equipment - Part 1-1: Generic blank detail specification
SIST EN IEC 60384-1-1:2022

IEC 60384-1-1:2022 establishes a generic template and specifies requirements to the content of detail specifications for capacitors within the IEC 60384-X series. This part of IEC 60384-1 is applicable to the drafting of detail specifications for fixed capacitors for use in electronic equipment.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-1:2021(Main)
Fixed capacitors for use in electronic equipment - Part 1: Generic specification
SIST EN IEC 60384-1:2021

This part of IEC 60384 is a generic specification and is applicable to fixed capacitors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62391-1:2016/AC:2019-08(Corrigendum)
Fixed electric double-layer capacitors for use in electric and electronic equipment - Part 1: Generic specification
SIST EN 62391-1:2016/AC:2019

IEC 62391-1:2015(E) is available as IEC 62391-1:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 62391-1:2015(E) applies to fixed electric double-layer capacitors (hereafter referred to as capacitor(s)) mainly used in d.c. circuits of electric and electronic equipment. This part of IEC 62391 establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. This edition includes the following significant technical changes with respect to the previous edition: a) enhancement of the scope to include electric (high power) application; b) implementation of Annex Q, replacing Clause 3 in the first edition; c) in addition, minor revisions related to tables, figures and references.

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-22:2019(Main)
Fixed capacitors for use in electronic equipment - Part 22: Sectional specification - Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2
SIST EN IEC 60384-22:2019

IEC 60384-22:2019 is available as IEC 60384-22:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60384-22:2019 is applicable to fixed unencapsulated surface mount multilayer capacitors of ceramic dielectric, Class 2, for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted on printed boards, or directly onto substrates for hybrid circuits. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance levels, lower performance levels are not permitted. This edition includes the following significant technical changes with respect to the previous edition: - revision of the structure in accordance with ISO/IEC Directives, Part 2:2016 (seventh edition) to the extent practicable, and for harmonizing with IEC 60384-21; - deletion of the description on the permissible reactive power in 6.2.2 because it is not appropriate for the purposes of this document; - the dimensions of 0201M in Annex A have been added.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60384-21:2019(Main)
Fixed capacitors for use in electronic equipment - Part 21: Sectional specification - Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1
SIST EN IEC 60384-21:2019

IEC 60384-21:2019 is available as IEC 60384-21:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60384-21:2019 is applicable to fixed unencapsulated surface mount multilayer capacitors of ceramic dielectric, Class 1, for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted on printed boards, or directly onto substrates for hybrid circuits. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. The object of this document is to prescribe preferred ratings and characteristics and to select from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance levels; lower performance levels are not permitted. This edition includes the following significant technical changes with respect to the previous edition: - revision of the structure in accordance with ISO/IEC Directives, Part 2:2016 to the extent practicable, and for harmonizing with IEC 60384-22; - deletion of the description on the permissible reactive power in 6.2.2 because it is not appropriate for the purposes of this document; - the dimensions of 0201M in Annex A have been added.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62391-1:2016/AC:2016-12(Corrigendum)
Fixed electric double-layer capacitors for use in electric and electronic equipment - Part 1: Generic specification
SIST EN 62391-1:2016/AC:2017

IEC corrigendum

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day