Radio-frequency connectors - Part 50: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 4,11 mm with quick lock system - Characteristic impedance 50 Ohm (type QMA)

IEC 61169-50:2014, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type QMA R.F. coaxial connectors with quick lock. The connectors are normally used with 50 Ohms corrugated cable and flexible cables for middle power applications in an operating range up to 6 GHz. It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications relative to type QMA connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirements.

Hochfrequenz-Steckverbinder - Teil 50: Rahmenspezifikation für koaxiale HF Steckverbinder mit 4,11 mm Innendurchmesser des Außenleiters und Schnellverriegelung - Wellenwiderstand 50 Ohm (Typ QMA)

Connecteurs pour fréquences radioélectriques - Partie 50: Spécification intermédiaire relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur des conducteurs extérieurs de 4,11 mm à système de verrouillage rapide - Impédance caractéristique 50 Ohm (type QMA)

L'IEC 61169-50:2014, qui est une spécification intermédiaire (SI), fournit des informations et des règles en vue de l'établissement de spécifications particulières (SP) relatives aux connecteurs coaxiaux pour fréquences radioélectriques de type QMA à verrouillage rapide. Les connecteurs sont normalement utilisés avec des câbles 50 Ohms annelés et des câbles souples pour des applications de moyenne puissance au sein d'une plage de fonctionnement inférieure ou égale à 6 GHz. Elle décrit les dimensions d'interface pour des connecteurs d'usage général, ainsi que des informations concernant les calibres et les essais obligatoires choisis dans l'IEC 61169-1, applicables à toutes les spécifications particulières ayant trait aux connecteurs de type QMA. La présente spécification indique les caractéristiques de performance recommandées à prendre en compte pour la rédaction d'une spécification particulière et elle couvre tous les programmes d'essais et les exigences de contrôle.

Radiofrekvenčni konektorji - 50. del: Področne specifikacije za visokofrekvenčne koaksialne konektorje z notranjim premerom zunanjih vodnikov 4,11 mm in zaklepnim sistemom - Karakteristična impedanca 50 Ohm (tip QMA) (IEC 61169-50:2014)

Ta del standarda IEC 61169, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij (DS) za radiofrekvenčne koaksialne konektorje vrste QMA z zaklepanjem. Konektorji se običajno uporabljajo s 50-ohmskim valovitim kablom in prožnimi kabli za srednjemočnostne uporabe v območju delovanja do 6 GHz. Opisuje dimenzije vmesnika za konektorje za splošni namen z informacijami o merjenju in obvezne preskuse, izbrane iz standarda IEC 61169-1, ki se uporabljajo za vse podrobne specifikacije v zvezi s konektorji tipa QMA.
Ta specifikacija določa priporočene lastnosti, ki jih je treba upoštevati pri sestavljanju podrobnih specifikacij, ter zajema vse urnike preskusov in zahteve za pregled.
OPOMBA: Izvirne mere so podane v metričnih merah. Vse nedimenzionirane slikovne konfiguracije so podane samo v referenčne namene.

General Information

Status
Published
Publication Date
12-Mar-2015
Current Stage
6060 - Document made available
Due Date
13-Mar-2015
Completion Date
13-Mar-2015

Buy Standard

Standard
EN 61169-50:2015
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 61169-50:2015
01-oktober-2015
5DGLRIUHNYHQþQLNRQHNWRUMLGHO3RGURþQHVSHFLILNDFLMH]DYLVRNRIUHNYHQþQH
NRDNVLDOQHNRQHNWRUMH]QRWUDQMLPSUHPHURP]XQDQMLKYRGQLNRYPPLQ
]DNOHSQLPVLVWHPRP.DUDNWHULVWLþQDLPSHGDQFD2KP WLS40$  ,(&


Radio-frequency connectors - Part 50: Sectional specifications RF coaxial connectors

with inner diameter of outer conductors 4.11 mm with quick lock system - Characteristics

impedance 50 Ohm (type QMA) (IEC 61169-50:2014)
Hochfrequenz-Steckverbinder - Teil 50: Rahmenspezifikation für koaxiale HF
Steckverbinder mit 4,11 mm Innendurchmesser des Außenleiters und
Schnellverriegelung - Wellenwiderstand 50 Ohm (Typ QMA) (IEC 61169-50:2014)

Connecteurs pour fréquences radioélectriques - Partie 50: Spécification intermédiaire

relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre

intérieur des conducteurs extérieurs de 4,11 mm à système de verrouillage rapide -

Impédance caractéristique 50 Ohm (type QMA) (IEC 61169-50:2014)
Ta slovenski standard je istoveten z: EN 61169-50:2015
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
SIST EN 61169-50:2015 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 61169-50:2015
---------------------- Page: 2 ----------------------
SIST EN 61169-50:2015
EUROPEAN STANDARD EN 61169-50
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 33.120.30
English Version
Radio-frequency connectors - Part 50: Sectional specification for
RF coaxial connectors with inner diameter of outer conductors
4,11 mm with quick lock system - Characteristic impedance
50 Ohm (type QMA)
(IEC 61169-50:2014)

Connecteurs pour fréquences radioélectriques - Partie 50: Hochfrequenz-Steckverbinder - Teil 50:

Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF Steckverbinder mit

coaxiaux pour fréquences radioélectriques avec diamètre 4,11 mm Innendurchmesser des Außenleiters und

intérieur des conducteurs extérieurs de 4,11 mm à système Schnellverriegelung - Wellenwiderstand 50 Ohm (Typ QMA)

de verrouillage rapide - Impédance caractéristique 50 Ohm (IEC 61169-50:2014)
(type QMA)
(IEC 61169-50:2014)

This European Standard was approved by CENELEC on 2014-11-27. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 61169-50:2015 E
---------------------- Page: 3 ----------------------
SIST EN 61169-50:2015
EN 61169-50:2015 - 2 -
Foreword

The text of document 46F/264/CDV, future edition 1 of IEC 61169-50, prepared by SC 46F "R.F. and

microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, R.F. connectors, R.F. and

microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote

and approved by CENELEC as EN 61169-50:2015.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2015-09-13
national level by publication of an identical national
standard or by endorsement
(dow) 2017-11-27
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such

patent rights.
Endorsement notice

The text of the International Standard IEC 61169-50:2014 was approved by CENELEC as a European

Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 61169-50:2015
- 3 - EN 61169-50:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),

the relevant EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is

available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio-frequency connectors - EN 61169-1 2013
Part 1: Generic specification - General
requirements and measuring methods
IEC 62037 series Passive RF and microwave devices, EN 62037 series
intermodulation level measurement
---------------------- Page: 5 ----------------------
SIST EN 61169-50:2015
---------------------- Page: 6 ----------------------
SIST EN 61169-50:2015
IEC 61169-50
Edition 1.0 2014-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio-frequency connectors –

Part 50: Sectional specification for RF coaxial connectors with inner diameter of

outer conductors 4,11 mm with quick lock system – Characteristic impedance
50 Ω (type QMA)
Connecteurs pour fréquences radioélectriques –
Partie 50: Spécification intermédiaire relative aux connecteurs coaxiaux pour
fréquences radioélectriques avec diamètre intérieur des conducteurs
extérieurs de 4,11 mm à système de verrouillage rapide – Impédance
caractéristique 50 Ω (type QMA)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX S
ICS 33.120.30 ISBN 978-2-8322-1901-0

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61169-50:2015
– 2 – IEC 61169-50:2014 © IEC 2014
CONTENTS

FOREWORD ........................................................................................................................... 3

INTRODUCTION ..................................................................................................................... 5

1 Scope .............................................................................................................................. 6

2 Normative references ...................................................................................................... 6

3 Mating face and gauge information .................................................................................. 7

3.1 Dimensions – General connectors ........................................................................... 7

3.1.1 Connector with socket-centre contact .............................................................. 7

3.1.2 Connector with pin-centre contact .................................................................... 9

3.2 Gauges for general purpose connectors ................................................................ 10

3.2.1 Gauge pins for socket-centre contact ............................................................. 10

3.2.2 Test procedure .............................................................................................. 11

4 Quality assessment procedures ..................................................................................... 11

4.1 General ................................................................................................................. 11

4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) .......................... 11

4.3 Test schedule and inspection requirements........................................................... 13

4.3.1 Acceptance tests ........................................................................................... 13

4.4 Procedures for the quality conformance ................................................................ 14

4.4.1 Quality conformance inspection ..................................................................... 14

4.4.2 Qualification approval and its maintenance .................................................... 15

5 Instructions for preparation of detail specifications ........................................................ 15

5.1 General ................................................................................................................. 15

5.2 Identification of the component ............................................................................. 15

5.3 Performance ......................................................................................................... 15

5.4 Marking, ordering information and related matters ................................................ 15

5.5 Selection of tests, test conditions and severities ................................................... 16

5.6 Blank detail specification pro-forma for type QMA connector ................................. 16

6 Marking ......................................................................................................................... 21

6.1 Marking of component ........................................................................................... 21

6.2 Marking and contents of package .......................................................................... 21

Figure 1 – Connector with socket centre contact (for dimensions, see Table 1) ....................... 7

Figure 2 – Female centre contact (for dimensions, see Table 1) ............................................. 7

Figure 3 – Connector with pin centre contact (for dimensions, see Table 2) ............................ 9

Figure 4 – Details of pin centre contact (for dimensions, see Table 2) ..................................... 9

Figure 5 – Gauge pin for socket-centre contact (for dimensions, see Table 3) ....................... 10

Table 1 – Dimensions of connector with socket centre contact ................................................ 8

Table 2 – Dimensions of connector with pin-centre contact ................................................... 10

Table 3 – Gauge dimensions for socket centre contact ......................................................... 11

Table 4 – Rating and characteristics ..................................................................................... 11

Table 5 – Acceptance tests ................................................................................................... 13

Table 6 – Periodic tests ........................................................................................................ 14

---------------------- Page: 8 ----------------------
SIST EN 61169-50:2015
IEC 61169-50:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 50: Sectional specification for RF coaxial connectors with inner
diameter of outer conductors 4,11 mm with quick lock system –
Characteristic impedance 50 Ω (type QMA)
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

International Standard IEC 61169-50 has been prepared by subcommittee 46F: R.F. and

microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,

R.F. connectors, R.F. and microwave passive components and accessories.
The text of this standard is based on the following documents:
CDV Report on voting
46F/264/CDV 46F/285/RVC

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,

can be found on the IEC website.
---------------------- Page: 9 ----------------------
SIST EN 61169-50:2015
– 4 – IEC 61169-50:2014 © IEC 2014

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates

that it contains colours which are considered to be useful for the correct

understanding of its contents. Users should therefore print this document using a

colour printer.
---------------------- Page: 10 ----------------------
SIST EN 61169-50:2015
IEC 61169-50:2014 © IEC 2014 – 5 –
INTRODUCTION

The International Electrotechnical Commission (IEC) draws attention to the fact that it is

claimed that compliance with this document may involve the use of a patent concerning the

design of the connector given in 3.1.

IEC takes no position concerning the evidence, validity and scope of this patent right.

The holder of this patent right has assured the IEC that he/she is willing to negotiate licence

under reasonable and non-discriminatory terms and conditions with applicants throughout the

world. In this respect, the statement of the holders of this patent right is registered with IEC.

More detailed information may be obtained from:
HUBER+SUHNER AG
Mr. Germann Reto, RF Division
Reto.germann@hubersuhner.com
Phone:+41 71 353 4653
Degersheimerstrasse 14, CH-9100 Herisau, Switzerland
Radiall SA
Mr. Pierre Bigot, RFI Division
Pierre.bigot@radiall.com
Phone:+33 47 650 0057
Z.I Centr’alp – 642 rue Emile Romanet, B.P. 35 – F-38341 Voreppe Cedex, France

Attention is drawn to the possibility that some of elements of this document may be the

subject of patent rights other than those identified above .IEC shall not be held responsible for

identifying any or all such patent rights.

ISO (www.iso.org/patents) and IEC (http://patents.IEC.ch) maintain on-line data bases of

patents relevant to their standards. Users are encouraged to consult the data bases for the

most up to date information concerning patents.
---------------------- Page: 11 ----------------------
SIST EN 61169-50:2015
– 6 – IEC 61169-50:2014 © IEC 2014
RADIO-FREQUENCY CONNECTORS –
Part 50: Sectional specification for RF coaxial connectors with inner
diameter of outer conductors 4,11 mm with quick lock system –
Characteristic impedance 50 Ω (type QMA)
1 Scope

This part of IEC 61169, which is a sectional specification (SS), provides information and rules

for the preparation of detail specifications (DS) for type QMA R.F. coaxial connectors with

quick lock.

The connectors are normally used with 50 Ω corrugated cable and flexible cables for middle

power applications in an operating range up to 6 GHz.

It describes the interface dimensions for general purpose connectors with gauging information

and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications

relative to type QMA connectors.

This specification indicates the recommended performance characteristics to be considered

when writing a DS and covers all tests schedules and inspection requirements.
NOTE Metric dimension are original dimensions.
All un-dimensioned pictorial configurations are for reference purpose only.
2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and

are indispensable for its application. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any
amendments) applies.

IEC 61169-1:2013, Radio-frequency connectors – Part 1: Generic specification – General

requirements and measuring methods

IEC 62037 (all parts), Passive RF and microwave devices, intermodulation level measurement

---------------------- Page: 12 ----------------------
SIST EN 61169-50:2015
IEC 61169-50:2014 © IEC 2014 – 7 –
3 Mating face and gauge information
3.1 Dimensions – General connectors
3.1.1 Connector with socket-centre contact
IEC
Figure 1 – Connector with socket-centre contact (for dimensions, see Table 1)
IEC
Figure 2 – Female centre contact (for dimensions, see Table 1)
-------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.