IEC 60255-23:1994
(Main)Electrical relays - Part 23: Contact performance
Electrical relays - Part 23: Contact performance
Is applicable to contact assemblies of relays within the scope of the IEC and covers basic considerations which are, in general, common to all types of relays covered by IEC 60255. Replaces and cancels IEC 60255-0-20.
Relais électriques - Partie 23: Caractéristiques fonctionnelles des contacts
Est applicable aux ensembles de contacts de relais entrant dans le domaine de la CEI et couvre les prescriptions fondamentales généralement communes à tous les types de relais faisant l'objet de la CEI 60255. Remplace et annule la CEI 60255-0-20.
Electrical relays - Part 23: Contact performance
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electrical relays - Part 23: Contact performanceRelais électriques - Partie 23: Caractéristiques fonctionnelles des contactsElectrical relays - Part 23: Contact performance29.120.70RelejiRelaysICS:Ta slovenski standard je istoveten z:IEC 60255-23 Ed. 1.0SIST IEC 60255-23:1995en01-avgust-1995SIST IEC 60255-23:1995SLOVENSKI
STANDARD
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
SIST IEC 60255-23:1995
...
This May Also Interest You
IEC 61812-1:2023 is available as IEC 61812-1:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61812-1:2023 applies to time relays and coupling relays for industrial applications (for example control, automation, signal and industrial equipment) and for automatic electrical controls for use in, on, or in association with equipment for residential and similar use.
The term “relay” as used in this document comprises all types of time relays and coupling relays, other than measuring relays. This document defines type test and routine test to confirm the service condition. Subclause 3.2 provides definitions for different types of time relays in use in the IEC 61812 series. IEC 61812-1:2023 cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) update of references;
b) addition of requirements for risk assessment;
c) addition of requirements for routine test;
d) renumbering of clauses to bring them into a more logical order;
e) clarification of the requirement for shock;
f) addition of cybersecurity requirements for industrial automation and control systems;
g) addition of environmentally conscious design requirement;
h) addition of common data dictionary reference;
i) addition of terms and definitions of relay types;
j) addition of coupling relays in title;
k) addition of coupling relays in scope.
- Standard133 pagesEnglish and French languagesale 15% off
IEC 62246-4:2023 gives additional requirements for the evaluation of functional characteristics on reed switching components operated by magnetic actuator and gives guidance for their implementation in selected applications.
This document specifies test and measurement procedures for the application of reed switch (contact) based magnetic sensors.
In case the application of a reed contact magnetic sensor determines additional requirements exceeding those specified in this document, the sensor is evaluated with this application in accordance with the relevant IEC or ISO standard(s) (e.g. IEC 62061 or ISO 13849 series, IEC 60335-1 and relevant parts of the IEC 60335-2 series, IEC 60730-1, IEC 61373, ISO 16750-3).
This document does not apply to:
– sensing or monitoring of the position of elements of interlocking devices for movable guards (see ISO 14119);
– sensing or monitoring of the position of elements of pressure sensitive protective equipment (PSPE, see ISO 13856 series);
– electrical equipment for measurement, control, and laboratory use (see IEC 61010-1);
– aircraft – proximity switches (see ISO 6859-1).
Information contained in this document is relevant to the application of a magnetic sensor on new installations as well as modifications to existing installations.
- Standard138 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish languagesale 15% off
IEC 62314:2022 applies to particular all-or-nothing electrical relays denominated solid-state relays intended for performing electrical operations by single step function changes to the state of electric circuits between the OFF-state and the ON-state and vice versa.
This document deals with solid-state relays which are intended for incorporation in other products or equipment. As such, solid-state relays are considered to be components and this document defines the basic safety-related and functional requirements for solid-state relays as stand-alone components.
Such solid-state relays are incorporated in products or equipment which themselves comply with the relevant product and/or application standard(s) to meet their intended application.
Solid state relay as apparatus:
Where the solid-state relay is specified as apparatus with a function to the end-user, requirements on EMC are given in this document.
Solid state relay as component:
There are no EMC requirements for solid-state relays intended for incorporation into the equipment by the equipment manufacturer, because the performance strongly depends on the application into the equipment.
The object of this document is to state:
– the characteristics of solid-state relays
– the requirements which apply to solid-state relays with reference to
a) electrical safety;
b) their operation and behaviour;
c) their dielectric properties;
d) EMC;
– the tests verifying that the requirements have been met, and the test methods to be adopted;
– the information to be given with the solid-state relay or in the product documentation.
Solid-state switching devices with monolithic structures fall within the scope of IEC sub-committee 47E and are not covered in this document.
Semiconductor controllers and contactors fall within the scope of the IEC 60947 series of standards – low-voltage switchgear and controlgear – developed by IEC subcommittee 121A and are not covered in this document.
IEC 62314:2022 cancels and replaces the first edition published in 2006. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) addition of load categories for DC load;
b) addition of load category for self-ballasted lamp load;
c) addition of "sockets" terminal;
d) update of references;
e) introduction of the requirement of EMC;
f) restructuring of the whole document.
- Standard110 pagesEnglish and French languagesale 15% off
IEC 61810-4:2020 applies to electromechanical elementary relays with reed switches (reed contacts) incorporated into general control circuits. It defines the basic functional and safety requirements in all areas of electrical engineering or electronics in accordance with the parts of IEC 61810 series and IEC 62246 series.
IEC 61810-4:2020 defines technical deviations/additions to IEC 61810-1. It specifies type tests, routine tests, special tests and environmental tests to confirm the service conditions for applications.
- Standard56 pagesEnglish and French languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
IEC 61810-10:2019, with functional and safety aspects, applies to electromechanical elementary relays (non-specified time all-or-nothing relays) with high capability requirements like breaking or short circuit capabilities and similar for incorporation into low-voltage equipment. These relays may have a specific design to extinguish the electric arc between contacts (e.g. by magnetic blow-out), or use an insulation coordination not covered by IEC 61810-1 (e.g. by gas filled contact chambers), or require safety assessments not covered by IEC 61810-1 (e.g. for higher loads).
It defines additional requirements for high-capacity relays with generic performance intended for use in applications in smart grids, electric vehicles and other applications where, for example, battery charge/discharge switching is used, such as:
• electrical energy storage (EES) systems,
• solar photovoltaic energy systems,
• electric road vehicles (EV) and electric industrial trucks,
• power electronic systems and equipment,
• secondary cells and batteries,
• road vehicles.
Compliance with the requirements of this standard is verified by the type tests indicated.
- Standard128 pagesEnglish and French languagesale 15% off
IEC 62246-1-1:2018 is a blank detail specification which defines requirements and tests for reed switches for use in general and industrial applications.
This document is intended to be used in conjunction with IEC 62246-1:2015 and specific products standards applying as switching elements.
This document selects from IEC 62246-1:2015 and from other sources the appropriate test procedures to be used in detail specifications derived from this specification.
Reed switch types are specified depending on characteristic values including functional ratings for safety and tests.
This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous editions:
a) update of the scope, references and terms and definitions;
b) inclusion of guidelines for the preparation of blank detail and detail specifications;
c) update of characteristics values including functional ratings for safety;
d) update of the quality conformance inspection procedures;
e) update of typical applications.
- Standard124 pagesEnglish and French languagesale 15% off
IEC 61810-2-1:2017 specifies reliability test procedures for electromechanical elementary relays when enhanced requirements for the verification of reliability apply.
Particular provisions are given for relays incorporated in safety-related control systems of machinery in accordance with IEC 62061 and ISO 13849-1. For such relays, B10 values for dangerous failures (B10D values) are derived from the tests specified in this document.
This edition includes the following significant technical changes with respect to the previous edition:
- limitation of tests to 10 M cycles in Clause 5;
- reduction of required number of test samples to 5 in specified cases;
- introduction of WeiBayes analysis for routine test under Clause 4.
- Standard33 pagesEnglish and French languagesale 15% off
IEC 61810-2:2017 covers test conditions and provisions for the evaluation of endurance tests using appropriate statistical methods to obtain reliability characteristics for relays.
This document applies to electromechanical elementary relays considered as non-repaired items (i.e. items which are not repaired after failure).
This document does not cover procedures for electromechanical elementary relays where enhanced requirements for the verification of reliability apply.
This edition includes the following significant technical changes with respect to the previous edition:
- not only graphical but also numerical methods are added;
- reduction of number of samples in specified cases;
- new subclauses of confidence intervals are added;
- the WeiBayes approach is added to facilitate compliance tests (routine test) with lower effort;
- annexes have been restructured into an Annex A for data analysis (normative) and Annex B (informative) where various examples of the data analysis are given;
- the former Annex C has been incorporated into the modified Annex B;
- a new Annex C replaces the old Annex D.
- Standard86 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.