iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC TS 62876-3-1:2022

(Main)

Nanomanufacturing - Reliability assessment - Part 3-1: Graphene-based material - Stability: Temperature and humidity test

Nanomanufacturing - Reliability assessment - Part 3-1: Graphene-based material - Stability: Temperature and humidity test

IEC TS 62876-3-1:2022(E) establishes a standardized method to determine the
• stability
of films of graphene-based material by a
• temperature and humidity test.
It establishes a general methodology for reliability stress screening (RSS) to qualify the use of graphene-based material in its subsequent product value stage. The intention is to prepare test samples undergoing the same or similar failure mechanisms as the graphene-based material in the final product.

General Information

Status
Published
Publication Date
17-Feb-2022
ICS
07.120 - Nanotechnologies
Technical Committee
TC 113 - Nanotechnology for electrotechnical products and systems
Drafting Committee
PT 62876-3-1 - TC 113/PT 62876-3-1
Current Stage
PPUB - Publication issued
Start Date
24-Mar-2022
Completion Date
18-Feb-2022
Ref Project

Buy Standard

IEC TS 62876-3-1:2022 - Nanomanufacturing - Reliability assessment - Part 3-1: Graphene-based material - Stability: Temperature and humidity testIEC TS 62876-3-1:2022 - Nanomanufacturing - Reliability assessment - Part 3-1: Graphene-based material - Stability: Temperature and humidity test
PreviousNext
Technical specification
IEC TS 62876-3-1:2022 - Nanomanufacturing - Reliability assessment - Part 3-1: Graphene-based material - Stability: Temperature and humidity test
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC TS 62876-3-1
®

Edition 1.0 2022-02
TECHNICAL
SPECIFICATION

colour
inside


Nanomanufacturing – Reliability assessment –
Part 3-1: Graphene-based material – Stability: Temperature and humidity test
IEC TS 62876-3-1:2022-02(en)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2022 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.


IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.

Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.

---------------------- Page: 2 ----------------------
IEC TS 62876-3-1

®


Edition 1.0 2022-02




TECHNICAL



SPECIFICATION








colour

inside










Nanomanufacturing – Reliability assessment –

Part 3-1: Graphene-based material – Stability: Temperature and humidity test


























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 07.120 ISBN 978-2-8322-1082-8




  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 3 ----------------------
– 2 – IEC TS 62876-3-1:2022 © IEC 2022
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
3.1 General terms . 7
3.2 Terms regarding reliability. 7
4 General . 9
4.1 Sample under test . 9
4.2 Sample description . 10
5 Reliability stress screening . 10
5.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC TS 62607-7-2:2023(Main)
Nanomanufacturing - Key control characteristics - Part 7-2: Nano-enabled photovoltaics - Device evaluation method for indoor light

IEC TS 62607-7-2:2023 specifies the efficiency testing of photovoltaic cells (excluding multi-junction cells) under indoor light. Although it is primarily intended for nano-enabled photovoltaic cells (organic thin-film, dye-sensitized solar cells (DSC), and Perovskite solar cells), it can also be applied to other types of photovoltaic cells, such as Si, CIGS, GaAs cells, and so on.

  • Technical specification
    48 pages
    English language
    sale 15% off
IEC
ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary

ISO 80004-1:2023 This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off
IEC
IEC TS 62565-5-1:2023(Main)
Nanomanufacturing - Product specifications - Part 5-1: Nanoporous activated carbon - Blank detail specification: Electrochemical capacitors

IEC TS 62565-5-1:2023, which is a Technical Specification, establishes a blank detail specification (BDS) for nanoporous activated carbon used for electrochemical capacitors.
Numeric values for the key control characteristics are left blank as they will be specified between customer and supplier in the detail specification (DS). In the DS key control characteristics can be added or removed if agreed between customer and supplier.

  • Technical specification
    37 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-7:2023(Main)
Nanomanufacturing - Key control characteristics - Part 6-7: Graphene - Sheet resistance: van der Pauw method

IEC TS 62607-6-7:2023 establishes a method to determine the key control characteristics sheet resistance RS [measured in ohm per square (Ω/sq)], by the van der Pauw method, vdP.
The sheet resistance RS is derived by measurements of four-terminal electrical resistance performed on four electrical contacts placed on the boundary of the planar sample and calculated with a mathematical expression involving the two resistance measurements.
The measurement range for RS of the graphene samples with the method described in this document goes from 10−2 Ω/sq to 104 Ω/sq.
The method is applicable for CVD graphene provided it is transferred to quartz substrates or other insulating materials (quartz, SiO2 on Si), as well as graphene grown from silicon carbide.
The method is complementary to the in-line four-point-probe method (4PP, IEC 62607-6-8) for what concerns the measurement of the sheet resistance and can be applied when it is possible to reliably place contacts on the sample boundary, avoiding the sample being scratched by the 4PP.
The outcome of the van der Pauw method is independent of the contact position provided the sample is uniform, which is typically not true for graphene at this stage. This document considers the case of samples with non-strictly uniform conductivity distribution and suggests a way to consider the sample inhomogeneity as a component of the uncertainty on RS.

  • Technical specification
    27 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-8:2023(Main)
Nanomanufacturing - Key control characteristics - Part 6-8: Graphene - Sheet resistance: In-line four-point probe

IEC TS 62607-6-8:2023 establishes a method to determine the key control characteristic sheet resistance RS [measured in ohm per square (Ω/sq)], by the in-line four-point probe method, 4PP.
The sheet resistance RS is derived by measurements of four-terminal electrical resistance performed on four electrodes placed on the surface of the planar sample.
The measurement range for RS of the graphene samples with the method described in this document goes from 10−2 Ω/sq to 104 Ω/sq.
The method is applicable for CVD graphene provided it is transferred to quartz substrates or other insulating materials (quartz, SiO2 on Si, as well as graphene grown from silicon carbide.
The method is complementary to the van der Pauw method (IEC 62607-6-7) for what concerns the measurement of the sheet resistance and can be useful when it is not possible to reliably place contacts on the sample boundary.

  • Technical specification
    22 pages
    English language
    sale 15% off
IEC
IEC TS 62565-1:2023(Main)
Nanomanufacturing - Product specifications - Part 1: Basic concepts

IEC TS 62565-1:2023 which is a Technical Specification, defines the system of blank detail specifications for nanomaterials and nano-assemblies as well as final nano-enabled products addressed in the nanomanufacturing value chain.
It defines the concepts of blank detail specification (BDS), detail specification (DS) and key control characteristic (KCC). Furthermore, it provides guidelines how to develop and use product specifications, particularly the IEC 62565 series, in the field of nanotechnology.
This document also provides guidelines regarding the certification and reliability aspects for products specified by a DS and associated KCCs.
NOTE 1 The IEC 62565 series uses an open generic structure that can be flexibly adapted to technical developments. The double indexing of the individual parts allows grouping into technology areas without restriction due to an overly strict hierarchical structure.
NOTE 2 Key elements of the IEC 62565 series are a consensus-based set of key control characteristics (KCCs) with clear definitions and standardized measurement procedures to measure them.

  • Technical specification
    29 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-17:2023(Main)
Nanomanufacturing - Key control characteristics - Part 6-17: Graphene-based material - Order parameter: X-ray diffraction and transmission electron microscopy

IEC TS 62607-6-17:2023 establishes a standardized method to determine the key control characteristic order parameter for graphene-based material and layered carbon material by X-ray diffraction (XRD) and transmission electron microscopy.
The order parameter is analysed from two perspectives: z-axis and x-y-axis. In the z-axis the order parameter is derived from the full width at half maximum (FWHM) of peak (002) in the XRD spectrum. In the x-y-axis, it is derived from the FWHM of peak (100) corresponding to diffraction patterns obtained by SAED (selected area electron diffraction) technique, which is routinely performed on most transmission electron microscopes in the world.
The method is applicable for graphene-based material and layered carbon material including graphite, expanded graphite, amorphous carbon, vitreous carbon or glassy carbon, the structures of which are clarified by other characterization techniques.
The method is applicable for differentiating few-layer graphene or reduced graphene oxide from layered carbon material.
Typical application area is quality control in manufacturing to ensure batch-to-batch reproducibility.
NOTE Graphene oxide, one type of graphene-based material, is not within the scope of this document.

  • Technical specification
    24 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-2:2023(Main)
Nanomanufacturing - Key control characteristics - Part 6-2: Graphene - Number of layers: atomic force microscopy, optical transmission, Raman spectroscopy

IEC TS 62607-6-2:2023 establishes a standardized method to determine the key control characteristic
- number of layers
for graphene flakes by a combination of
- atomic force microscopy,
- optical transmission, and
- Raman spectroscopy

  • Technical specification
    24 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-18:2022(Main)
Nanomanufacturing - Key control characteristics - Part 6-18: Graphene-based material - Functional groups: TGA-FTIR

IEC TS 62607-6-18:2022(E) establishes a standardized method to determine the chemical key control characteristic
functional groups  for functionalized graphene-based material and graphene oxide by
thermogravimetry analysis (TGA) coupled with Fourier transform infrared spectroscopy (FTIR), referred to as TGA-FTIR.  The content of functional groups is derived by changes in mass of the sample as a function of temperature using TGA. Materials evolved during these mass changes are then analysed using coupled FTIR to identify functional groups.
The functional groups determined according to this document will be listed as a key control characteristic in the blank detail specification for graphene IEC 62565-3-1 for graphene powder.
The method is applicable for functionalized graphene powder and graphene oxide that can be pyrolysed and gasified with elevated temperature during TGA.
Typical application areas are quality control for graphene manufacturers, and product selection for downstream users.

  • Technical specification
    19 pages
    English language
    sale 15% off
IEC
IEC TS 62607-6-5:2022(Main)
Nanomanufacturing - Key control characteristics - Part 6-5: Graphene-based materials - Contact and sheet resistance: transmission line measurement

IEC TS 62607-6-5:2022(E) establishes a standardized method to determine the key control characteristics
contact resistance, and
sheet resistance  for graphene-based materials and other two-dimensional materials by a
transmission line measurement.  The method uses test structures applied to the 2D material by photolithographic methods consisting of several metal electrodes with increasing spacing between the electrodes. By a measurement of the voltage drop between different pairs of electrodes, sheet resistance and contact resistance can be calculated.
The method can be applied to any other two-dimensional materials which are subject to electrical metal contact on top of the materials.
The method provides accurate and reproducible results, if the electrical contact formed between the two-dimensional material and the metal electrodes provides ohmic contact property.

  • Technical specification
    23 pages
    English language
    sale 15% off