Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock

IEC 60068-2-27:2008 provides a standard procedure for determining the ability of a specimen to withstand specified severities of non-repetitive or repetitive shocks. The purpose of this test is to reveal mechanical weakness and/or degradation in specified performances, or accumulated damage or degradation caused by shocks. In conjunction with the relevant specification, this may be used in some cases to determine the structural integrity of specimens or as a means of quality control. This test is primarily intended for unpackaged specimens and for items in their transport case when the latter may be considered to be part of the specimen. If an item is to be tested unpackaged, it is referred to as a test specimen. However, if the item is packaged, then the item itself is referred to as a product and the item and its packaging together are referred to as a test specimen. When used in conjunction with IEC 60068-2-47, this standard may be used for testing packaged products. This possibility was included in the 2005 version of IEC 60068-2-47 for the first time. This standard is written in terms of prescribed pulse shapes. Guidance for the selection and application of these pulses is given in Annex A and the characteristics of the different pulse shapes are discussed in Annex B. Wherever possible, the test severity and the shape of the shock pulse applied to the specimen should be such as to reproduce the effects of the actual transport or operational environment to which the specimen will be subjected, or to satisfy the design requirements if the object of the test is to assess structural integrity (see Clauses A.2 and A.4). For the purposes of this test, the specimen is always mounted to the fixture or the table of the shock testing machine during testing. The major changes with regard to the previous edition concern:
- the merging of IEC 60068-2-29 into this edition of IEC 60068-2-27; Part 2-29 will be withdrawn as soon as this edition is published;
- the introduction of soft packaged specimens as defined in the IEC ad hoc working group document agreed in Stockholm:2000.

Essais d'environnement - Partie 2: Essais - Essai Ea et guide: Chocs

IEC 60068-2-27:2008 fournit un mode opératoire normalisé pour déterminer l'aptitude d'un spécimen à supporter des chocs répétitifs ou non répétitifs de sévérités spécifiées. Le but de cet essai est de mettre en évidence une défaillance mécanique et/ou une dégradation des performances spécifiées, ou les dommages ou dégradations cumulés dus aux chocs. Il peut aussi être utilisé dans certains cas, conjointement à la spécification particulière, pour déterminer la robustesse de structure des spécimens ou comme essai d'assurance de la qualité. Cet essai est en premier lieu destiné aux spécimens non emballés et aux éléments placés dans leur coffret de transport lorsque ce dernier peut être considéré comme faisant partie du spécimen. Si un élément est à soumettre aux essais en étant non emballé, il est désigné comme un spécimen d'essai. Cependant, si l'élément est emballé, alors il est lui-même désigné comme produit et l'élément et son emballage sont désignés comme spécimen d'essai. Lorsque cette norme est utilisée conjointement avec la CEI 60068-2-47, elle peut être utilisée pour l'essai des produits emballés. Cette possibilité a été incluse dans la version de 2005 pour la première fois. La rédaction de cette norme s'appuie sur des formes d'impulsions prescrites. Un guide pour la sélection et l'application de ces impulsions est donné à l'Annexe A et les caractéristiques des différentes formes d'impulsion sont exposées à l'Annexe B. Chaque fois que possible, il convient que la sévérité d'essai et la forme de l'impulsion de choc appliquée au spécimen soient telles qu'elles reproduisent les effets du transport ou des conditions d'environnement réels auxquels le spécimen sera soumis ou qu'elles correspondent aux exigences de la conception si l'objet de l'essai est d'estimer la robustesse de structure (voir Articles A.2 et A.4). Pour les besoins de cet essai, le spécimen est toujours monté sur le bâti de fixation ou sur la table de la machine d'essai au choc pendant l'épreuve. Les modifications principales par rapport à l'édition précédente sont les suivantes:
- la fusion de la CEI 60068-2-29 dans la présente édition de la CEI 60068-2-27; la Partie 2-29 sera supprimée dès que cette édition sera publiée;
- l'introduction de spécimens dans emballages mous comme définis dans le document du groupe de travail ad hoc de la CEI conclu à Stockholm en 2000.

General Information

Status
Published
Publication Date
26-Feb-2008
Current Stage
PPUB - Publication issued
Start Date
15-Mar-2008
Completion Date
27-Feb-2008
Ref Project

Buy Standard

Standard
IEC 60068-2-27:2008 - Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
English and French language
75 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 60068-2-27
Edition 4.0 2008-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BASIC SAFETY PUBLICATION
PUBLICATION FONDAMENTALE DE SÉCURITÉ
Environmental testing –
Part 2-27: Tests – Test Ea and guidance: Shock

Essais d'environnement –
Partie 2-27: Essais – Essai Ea et guide: Chocs

IEC 60068-2-27:2008

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2008 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00

---------------------- Page: 2 ----------------------
IEC 60068-2-27
Edition 4.0 2008-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BASIC SAFETY PUBLICATION
PUB
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.