IEC 60317-36:1992

Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer

This standard applies to microwave measuring apparatus and microwave measuring techniques.

Spécifications pour types particuliers de fils de bobinage - Partie 36: Fil de section circulaire en cuivre émaillé avec polyesterimide brasable, classe 180, avec une couche adhérente

S'applique aux appareils de mesure en micro-ondes et aux techniques de mesure en micro-ondes.

Terminologija za mikrovalovne naprave

General Information

• Status: Published
• Publication Date: 14-Jul-1992
• ICS: 01.040.29 - Electrical engineering (Vocabularies)
• ICS: 29.060.10 - Wires
• Technical Committee: TC 55 - Winding wires
• Drafting Committee: WG 1 - TC 55/WG 1
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 14-Oct-2013
• Ref Project: SIST IEC 60615:1995 - Terminology for microwave apparatus

Relations

• Amended By: IEC 60317-36:1992/AMD1:1997 - Amendment 1 - Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer
• Effective Date: 05-Sep-2023
• Revised: IEC 60317-36:2013 - Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer
• Effective Date: 05-Sep-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST IEC 60615:1995
01-avgust-1995
Terminologija za mikrovalovne naprave
Terminology for microwave apparatus
Terminologie pour appareils à micro-ondes
Ta slovenski standard je istoveten z: IEC 60615
ICS:
01.040.29 Elektrotehnika (Slovarji) Electrical engineering
(Vocabularies)
29.020 Elektrotehnika na splošno Electrical engineering in
general
SIST IEC 60615:1995 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST IEC 60615:1995

---------------------- Page: 2 ----------------------

SIST IEC 60615:1995
CEI
NORME
IEC
INTERNATIONALE
615
INTERNATIONAL
Première édition
STAN DARD
First edition
1978-01
pour appareils à micro-ondes
Terminologie
Terminology for microwave apparatus
© CEI 1978 Droits de reproduction réservés — Copyright - all rights reserved
No part of this publication may be reproduced or utilized
Aucune partie de cette publication ne peut être reproduite ni
in any form or by any means, electronic or mechanical,
utilisée sous quelque forme que ce soit et par aucun procédé,
including photocopying and microfilm, without permission
électronique ou mécanique, y compris la photocopie et les
in writing from the publisher
microfilms, sans l'accord écrit de l'éditeur.
Suisse
Bureau central de la Commission Electrotechnique Internationale 3, rue de Varembé Genève
CODE PRIX
Commission Electrotechnique Internationale
S
PRICE CODE
International Electrotechnical Commission
IEC
Me»tayHapojuae aleKTpOTeXHH4eCHaR HOMHCCHA
Pour prix, voir catalogue en vigueur
• •
For price, see current catalogue

---------------------- Page: 3 ----------------------

SIST IEC 60615:1995
— 3 —
CONTENTS
Page
FOREWORD 5
PREFACE 5
Clause

7
1. General

7
2. General terms

13
3. Frequency

15
4. Immittance

31
5.
Noise figure

33
6. Power, attenuation and gain

41
7. Signals

---------------------- Page: 4 ----------------------

SIST IEC 60615:1995
5
INTERNATIONAL ELECTROTECHNICAL COMMISSION
TERMINOLOGY FOR MICROWAVE APPARATUS
FOREWORD
1) The formal decisions or agreements of the I E C on technical matters, prepared by Technical Committees on which all the
National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
They have the form of recommendations for international use and they are accepted by the National Committees in that
2)
sense.
In order to promote international unification, the IEC expresses the wish that all National Committees should adopt the
3)
text of the 1 E C recommendation for their national rules in so far as national conditions will permit. Any divergence
between the IEC recommendation and the corresponding national rules should, as far as possible, be clearly indicated in
the latter.
PREFACE
This standard has been prepared by IEC Technical Committee No. 66, Electronic Measuring
Equipment.
A first draft was discussed at the meeting held in Baden-Baden in 1972. The draft, Document
66(Central Office)20, was submitted to the National Committees for approval under the Six
Months' Rule in September 1975.
The following countries voted explicitly in favour of publication:
Netherlands
Australia
Poland
Belgium
Denmark Spain
Finland Sweden
Turkey
France
Union of Soviet
Germany
Socialist Republics
Hungary
United Kingdom
Italy
Japan United States of America
This standard complements the definitions appearing in Chapter 62 of the International
Electrotechnical Vocabulary: Waveguides, published in 1961. This chapter, incidentally, is under
revision at the time of publication of the present standard.

---------------------- Page: 5 ----------------------

SIST IEC 60615:1995
7 —
TERMINOLOGY FOR MICROWAVE APPARATUS
1. General
1.1 Scope
This standard applies to microwave measuring apparatus and microwave measuring
techniques.
Note. —
The term microwaves is used to signify radio waves in the frequency range from about 1 GHz upwards.
(The low-frequency boundary of the microwave range is usually considered to be where lower-frequency
techniques and lumped circuit elements cannot generally be used efficiently. It is then necessary to apply
distributed line techniques and transmission line theory.)
1.2
Object
To establish the essential definitions related to microwave measuring techniques and
apparatus.
2. General terms
2.1 Anechoic chamber
A space bounded by absorbing wall coating, such that the walls can be considered as being
non-reflective for electromagnetic waves in a stated frequency range.
2.2 Cavity resonator
A space bounded by conductive coating to obtain resonance of a specific mode at a stated
frequency.
2.2.1
Echo box
A tunable cavity resonator used for the purpose of supplying a signal at a particular
frequency to adjust a radar receiver. This signal is available during the "ringing" time of the
resonator, after the tr
...